PDA

View Full Version : Electrical Driver's Door Issues



SShaw
10-02-2016, 09:14 PM
I'm having some issues with my driver's side door. When it's open the door ajar light doesn't come on, the buzzer doesn't sound (with the key in) and the dome light doesn't come on when it's in the auto position. The door lights work just fine. Both plungers are good, I swapped the wires for the door lights between plungers and they still work. Everything functions as normal on the passenger's side, door lights, door ajar and dome light. Any thoughts?

purple/blue and black are controlling the door lights
purple/blue and purple/white don't seem to be doing anything

Thanks for the help.

David T
10-02-2016, 10:31 PM
I'm having some issues with my driver's side door. When it's open the door ajar light doesn't come on, the buzzer doesn't sound (with the key in) and the dome light doesn't come on when it's in the auto position. The door lights work just fine. Both plungers are good, I swapped the wires for the door lights between plungers and they still work. Everything functions as normal on the passenger's side, door lights, door ajar and dome light. Any thoughts?

purple/blue and black are controlling the door lights
purple/blue and purple/white don't seem to be doing anything

Thanks for the help.

There are 2 pairs of wires grouped into each pair with some tape. The 2 purple/blue wires are NOT the same wire and cannot be confused. Check to make sure you use the correct P/U (purple/Blue) wire with the black wire. Those 2 control the door lights and the door ajar light. The other 2 wires, the P/U and the P/W (purple white) are for the logic buzzer. Once you have verified you have not mixed up the P/U wires and that doesn't fix things, there are some diodes that may have failed. The dome light may have dirty contacts, check out both lights, there is one over the parcel shelf too. There is also a relay to delay the lights. For troubleshooting purposes, just remove it till you get everything working. There is a simplified wiring schematic in your Workshop Manual at M:18:12

SShaw
10-02-2016, 11:14 PM
There are 2 pairs of wires grouped into each pair with some tape. The 2 purple/blue wires are NOT the same wire and cannot be confused. Check to make sure you use the correct P/U (purple/Blue) wire with the black wire. Those 2 control the door lights and the door ajar light. The other 2 wires, the P/U and the P/W (purple white) are for the logic buzzer. Once you have verified you have not mixed up the P/U wires and that doesn't fix things, there are some diodes that may have failed. The dome light may have dirty contacts, check out both lights, there is one over the parcel shelf too. There is also a relay to delay the lights. For troubleshooting purposes, just remove it till you get everything working. There is a simplified wiring schematic in your Workshop Manual at M:18:12

I just double checked the wiring and everything seems to be in order. I also confirmed that both dome lights work as expected in the auto position with the passenger side door. It's weird that the door ajar light works on the passenger's side but not on the driver's side since the driver's side door lights work.

SShaw
10-03-2016, 01:20 AM
I swapped diodes around and that seems to be the problem. I got the driver's side functioning properly and now the passenger's side doesn't. The only thing I didn't get to work is the buzzer, but I think I'm ok with that :).

spikeygg
10-03-2016, 04:33 PM
I swapped diodes around and that seems to be the problem. I got the driver's side functioning properly and now the passenger's side doesn't. The only thing I didn't get to work is the buzzer, but I think I'm ok with that :).

Could you please take a picture of the diodes? I'm wondering what they look like.

Also, are the dome lights supposed to light up when the doors are ajar? I ask because mine don't do this... The lights appear to have three positions: tilted forward, flat, and tilted backwards. Only one position turns the lights on in my car.

Thanks,
-Greg

David T
10-03-2016, 06:00 PM
Proper operation of the interior lights is:
flat is off
tilted one way the light is always on
tilted the other way the light is on only when either or both doors are open
Each light operates independently of the other meaning you can set one to never light (flat) and the other can light when the doors are open.

SShaw
10-03-2016, 08:03 PM
And here are the diodes. Located to the right of the diver's right leg. One of mine is bad causing the dome lights and ajar light to not function for one of the doors. I've ordered a replacement.

46463

spikeygg
10-03-2016, 08:37 PM
Proper operation of the interior lights is:
flat is off
tilted one way the light is always on
tilted the other way the light is on only when either or both doors are open
Each light operates independently of the other meaning you can set one to never light (flat) and the other can light when the doors are open.

Thanks David, mine don't work with the door ajar. Do the dome lights rely on the same button/switch that triggers the door lights?


And here are the diodes. Located to the right of the diver's right leg. One of mine is bad causing the dome lights and ajar light to not function for one of the doors. I've ordered a replacement.

46463

Perfect, thanks for the photo. So I just went out and measured all three of my diodes and they appear to be working (only allowing current in one direction) but there is a large resistance when they are forward biased (~600Ω). Is this acceptable/expected?

46464 46465 46466

Thanks,
-Greg

Bitsyncmaster
10-03-2016, 08:42 PM
Perfect, thanks for the photo. So I just went out and measured all three of my diodes and they appear to be working (only allowing current in one direction) but there is a large resistance when they are forward biased (~600Ω). Is this acceptable/expected?

46464 46465 46466

Thanks,
-Greg

With your meter set to the "diode" range. That reading is the voltage drop over the diode. So your dropping 0.6 volts forward biased which is good.

I'm surprised your Fluke meter shows the ohms sign and does not read .600 like my Fluke meter does.

spikeygg
10-03-2016, 08:55 PM
With your meter set to the "diode" range. That reading is the voltage drop over the diode. So your dropping 0.6 volts forward biased which is good.

I'm surprised your Fluke meter shows the ohms sign and does not read .600 like my Fluke meter does.

Thanks Dave, any ideas what's next to check if my dome light doesn't lite up when I open the doors? I know my door switches work cause the door lights go off and on but the dome stays off in two orientations...

Bitsyncmaster
10-03-2016, 09:07 PM
Thanks Dave, any ideas what's next to check if my dome light doesn't lite up when I open the doors? I know my door switches work cause the door lights go off and on but the dome stays off in two orientations...

I have had a few customers find the wiring on the dome lights was not connected correctly. The purple wire has to connect to the "common" "on the lamp" terminal. You have to check both dome lights for that wiring.

spikeygg
10-03-2016, 09:22 PM
I have had a few customers find the wiring on the dome lights was not connected correctly. The purple wire has to connect to the "common" "on the lamp" terminal. You have to check both dome lights for that wiring.

I'm not sure what "common" is but it looks like one of mine might be hooked up backwards if "common" means middle... Can you share a picture of the correct configuration if this is incorrect?

46467 46468

Thanks,
-Greg

BABIS
10-04-2016, 05:56 AM
I'm not sure what "common" is but it looks like one of mine might be hooked up backwards if "common" means middle... Can you share a picture of the correct configuration if this is incorrect?

46467 46468

Thanks,
-Greg

I am pretty sure that the lamp on the second pic should have the purple wire in the middle. I'd replace the front lamp housing since it looks quite damaged..

Bitsyncmaster
10-04-2016, 06:24 AM
By common I mean that wire is connected to the terminal that is always connected to on end of the lamp. The other two wires are switched to connecting the other end of the lamp.

So you need to look closely at the fixture to follow the connections. There are a few different replacement fixtures finding there way into our cars so hard to determine by photo where the connections are. A few fixtures also have a diode in them that may need to be bypassed.

spikeygg
10-04-2016, 09:51 AM
By common I mean that wire is connected to the terminal that is always connected to on end of the lamp. The other two wires are switched to connecting the other end of the lamp.

So you need to look closely at the fixture to follow the connections. There are a few different replacement fixtures finding there way into our cars so hard to determine by photo where the connections are. A few fixtures also have a diode in them that may need to be bypassed.

Oh, gotcha! I'll probe it out and determine which one is the "common" pin. Thanks Dave!

spikeygg
10-05-2016, 12:07 AM
So I determined that both of my dome lights were wired incorrectly. I fixed the wiring and now they light up if I tilt them backward or forward. When I tilt them forward they seem extra bright and are not affected at all when I toggle the door switches. When I tilt them backward, I tried hitting both door switches at the same time and the light doesn't go out but it does dim a little when toggle one of the door switches and hold the other in. That makes me think it's trying to work but not quite pulling it off. The switches do turn off the door lights when they are depressed.

What can I check/do if I have this condition?

Thanks,
-Greg

SShaw
10-05-2016, 12:39 AM
So I determined that both of my dome lights were wired incorrectly. I fixed the wiring and now they light up if I tilt them backward or forward. When I tilt them forward they seem extra bright and are not affected at all when I toggle the door switches. When I tilt them backward, I tried hitting both door switches at the same time and the light doesn't go out but it does dim a little when toggle one of the door switches and hold the other in. That makes me think it's trying to work but not quite pulling it off. The switches do turn off the door lights when they are depressed.

What can I check/do if I have this condition?

Thanks,
-Greg

A relay in the fuse compartment keeps the lights on for about 10 seconds once the door is closed. While testing, be sure to keep the plungers pressed for at least that long. Beyond that, I'm not much help.

Bitsyncmaster
10-05-2016, 06:33 AM
A relay in the fuse compartment keeps the lights on for about 10 seconds once the door is closed. While testing, be sure to keep the plungers pressed for at least that long. Beyond that, I'm not much help.

The OEM door light delay unit only seems to work with the incandescent bulbs and not LED bulbs.

You get two diode drops in the dome light voltage when in auto position. With a working dome light delay that voltage drop is bypassed.

spikeygg
10-05-2016, 03:00 PM
The OEM door light delay unit only seems to work with the incandescent bulbs and not LED bulbs.

You get two diode drops in the dome light voltage when in auto position. With a working dome light delay that voltage drop is bypassed.

Ha, I wondered if this was going to be an issue. I have the LEDs in both my dome lights. I'm guessing if I get your dome light dimmer relay, all will work as designed with these LEDs? :)

Bitsyncmaster
10-05-2016, 04:31 PM
Ha, I wondered if this was going to be an issue. I have the LEDs in both my dome lights. I'm guessing if I get your dome light dimmer relay, all will work as designed with these LEDs? :)

As long as your LEDs don't have switching regulators, my unit will work. Most people just pull out the OEM dome unit with LEDs but then you don't get any delayed or dimming off funtion.

spikeygg
10-06-2016, 05:08 PM
As long as your LEDs don't have switching regulators, my unit will work. Most people just pull out the OEM dome unit with LEDs but then you don't get any delayed or dimming off funtion.

Thanks Dave, I just tried removing the relay and it works like a charm. How do I know if there are switching regulators in the LEDs? I ordered mine from DMC, they look like this one (http://store.delorean.com/p-6940-led-engine-cmptoem-dome-lightlic-plt-light.aspx).

Bitsyncmaster
10-06-2016, 08:50 PM
Thanks Dave, I just tried removing the relay and it works like a charm. How do I know if there are switching regulators in the LEDs? I ordered mine from DMC, they look like this one (http://store.delorean.com/p-6940-led-engine-cmptoem-dome-lightlic-plt-light.aspx).

Look at the back side of the LED. The switching regulators have large caps and inductors (large cylinders). As far as I know, only Super Bright sell some LEDs with the switching regulators. None of the LEDs door, dome, trunk, engine bay and glove box can be switching regulator type.