PDA

View Full Version : Frame & Body Washer Fluid Hose



spikeygg
10-07-2016, 11:02 PM
While I was fixing my luggage compartment light, I pulled my washer tank out and found that the hose was in very poor shape. It had been kinked in several places and it's 30+ years old so it isn't elastic anymore but very hard. I found three couplers inline before it enters the passenger compartment and I've replaced all those with one. I have consulted a friend who has removed the dash and he told me that I could remove the glove box and reach (by hand) the other end of the hose where it meets the windshield wipers. I just pulled the glove box out and I can actually reach the wiper washer connection but since the hose is so hard I can't slide it off the barbed fitting.

Here is the comparison of the old and new hose:
46536

Here is a bad picture of the connection I'm trying to separate (sorry my phone barely fit through the opening):
46533

Here is the connection on the outside:
46534

Here is my ghetto windshield washer, apparently whoever worked on this last didn't have the correct fix so they just did this:
46535

My first question is:
Does anyone have suggestions of ways to make it easier to pull the old hose off the barb? I tried heating up the easy end (in the first picture) with a heat gun and trying to slide it off but it still wouldn't let go. I'm not sure what is the most effective way to disconnect it without breaking the plastic barb. The other couplers I removed by slicing the hose along the length of the barbed fitting carefully in a few places so it would widen and let go but I don't think I can even fit a blade into this hole under the dash much less be able to see what I'm doing... Might be the only way tho. :(

My second question is:
How can I properly fix the sprayer so it doesn't look like a "farmer fix"? I'm not sure what it should look like, if someone could shoot a picture of their windshield washer sprayer it would be helpful. Should it be attached to the blade (as it seems to be now) or the wiper arm? Wiper arm makes more sense to me but my wiper arm doesn't appear to have any spot for it to mount. If it's the blade, do we need to use DMC blades with the washer mount?

Thanks,
-Greg
P.S. I find it very interesting that the washer fluid hose comes into the cabin only to go back out to the windshield wipers. This car keeps making me go "WTF?"

spikeygg
10-08-2016, 12:40 AM
Okay, I was able to run the new hose all the way but I went about it a different way than I was planning:
46539

I tried to pull the pull the screen cowl piece just under the windshield but it's wedged between a bracket beneath the windshield and the hood bump-stop. Is there an easy way to remove the bump-stop?
46538

I tried to twist it but it just spins, the hardware at the bottom of it just seems to spin up and down the threaded stud...

David T
10-08-2016, 11:18 AM
Okay, I was able to run the new hose all the way but I went about it a different way than I was planning:
46539

I tried to pull the pull the screen cowl piece just under the windshield but it's wedged between a bracket beneath the windshield and the hood bump-stop. Is there an easy way to remove the bump-stop?
46538

I tried to twist it but it just spins, the hardware at the bottom of it just seems to spin up and down the threaded stud...

The riv-nut is spinning, the bumper stop should just unscrew out. Careful with the sprayer on the wiper arm, they are NLA.

spikeygg
10-08-2016, 11:45 AM
The riv-nut is spinning, the bumper stop should just unscrew out.

Is the riv-nut supposed to be attached to the underside of the fender? I'm not sure what a riv-nut is. If it is supposed to attach to the underside of the fender, if I unscrew the bump-stop will it fall off inside? :(


Careful with the sprayer on the wiper arm, they are NLA.
What do you mean about the sprayer? Does NLA mean No Longer Available? How is the sprayer supposed to attach?

David T
10-08-2016, 06:38 PM
A riv-nut is like a big pop rivet that is threaded internally. It is locked into place in a hole in the fiberglass and is not supposed to spin. NLA does mean No Longer Available. The spray nozzle is supposed to snap on over the arm of the wiper blade with some tabs that are broken off on yours which is why yours is held on with some wire. That's OK, just don't break the nipple off where the hose attaches or you won't be able to use it at all. If necessary use a heat gun to soften the hose so it will slip on. Leave enough slack so the wiper arm can move without stretching the hose.

mluder
10-08-2016, 11:05 PM
Is the riv-nut supposed to be attached to the underside of the fender? I'm not sure what a riv-nut is. If it is supposed to attach to the underside of the fender, if I unscrew the bump-stop will it fall off inside? :(


What do you mean about the sprayer? Does NLA mean No Longer Available? How is the sprayer supposed to attach?

The sprayer is currently available at DMC Houston or your most local affiliate... $23 - http://store.delorean.com/p-6977-wiper-arm-jet.aspx

Cheers
Steve