View Full Version : Electrical Craig radio internal spring lost and needs helping finding its home
Jonathan
10-17-2016, 09:43 AM
Paging Dave Graham...
Or anyone that might know... :)
I replaced my stereo a few years ago. Did the deck, bracket, speakers and wiring. It was probably just the speakers that really needed attention, but I didn't know that until getting into it. My Craig stereo worked fine, radio was ok and the tape deck worked, but it wouldn't do some of the "auto reverse" functions.
I was going through some parts boxes figuring out what I might sell or get rid of and got looking at the Craig again. When tipping it up or down, I could hear something sliding around a little inside it. I opened it up and found a spring not connected to anything. I figured this could be my auto-reverse problem.
Anyone know what this little guy is supposed to connect to?
It was lying pretty much in that gap where you can see it with the screw driver pointing to one end.
467394673746738
Elvis
10-17-2016, 12:27 PM
it's almost at home on the second picture. white plastic piece - a little piece of the plastic broke off.
With a vice it can be repaired in a minute.
Jonathan
10-17-2016, 02:40 PM
it's almost at home on the second picture. white plastic piece - a little piece of the plastic broke off.
With a vice it can be repaired in a minute.
Thanks for pointing that out, Elvis.
I looked closer where you said and can see the spot where that small piece of plastic broke away. I assume the other end of that spring would have secured to the post straight up from that plastic portion?
If you were to fix this, how would you do it? I mean, what would you do with that broken plastic piece to give me something to secure the spring to?
DMC-81
10-17-2016, 07:55 PM
Hi Jonathan,
I repaired the same thing as part of my Craig radio refurb. Here is a thread with pictures of my adventure...
http://dmctalk.org/showthread.php?13755-Craig-W460-repair-help
There's more details and experimentation on page 5 of my Interior Restoration album.
Jonathan
10-18-2016, 11:55 AM
Wow, good thread. Looks like that plastic clip breaking off is common. And not too terribly hard to correct. Hope I don't have to get into the flex-cable repairs you did later on in that write-up!
I'll get at it and see how it goes. Thanks for the help.
DMC-81
10-18-2016, 09:34 PM
You're welcome.
As for the flex cable, I would suggest trying not to take the black plastic front cover off. When I did, the door extended flat (as it's on a spring), and I think that's what finished off the break in the cable. Maybe it would have broken soon anyway in that area.
Good luck with the repair.
David T
10-18-2016, 11:23 PM
You're welcome.
As for the flex cable, I would suggest trying not to take the black plastic front cover off. When I did, the door extended flat (as it's on a spring), and I think that's what finished off the break in the cable. Maybe it would have broken soon anyway in that area.
Good luck with the repair.
Doesn't matter if you take the cover apart or not. If you open the cover (bend the flex cable) enough it will break. You might just as well do the repair now as long as you have the radio out and apart.
DMC-81
10-19-2016, 09:50 PM
Doesn't matter if you take the cover apart or not. If you open the cover (bend the flex cable) enough it will break. You might just as well do the repair now as long as you have the radio out and apart.
Although,in my case, it did matter. My display worked perfectly before I took the radio apart. When I took the front cover off (with the unit upside down), the door bent at an angle that was outside its installed range of motion. Hence the connection on the cable immediately broke. Like I said in the thread, I was glad that it broke while it was out of the car so I could have it repaired.
I agree, if you are wanting to do a full radio refurb, you should inspect the cable and repair it if it shows cracking "while you're in there", but I think that depends on what the goals of the OP are for this radio.
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.