View Full Version : Electrical Bosch Starter Wire connections and heat shield plate
1batt4u
10-27-2016, 11:51 PM
Question on the starter wires and how to position them with headers on. I have a Bosch starter, Josh's s/s exhaust kit, and Hervey's heat shield for starter.
1. Red battery wire, red jump start post wire and brown alternator wire go on top as I have them. Other wire which is white or beige with red stripe connects to the right of it? How about the wire with Green and yellow stripe where does that go? I have seen other pictures of starters and connects right under the beige red wire, but no where to connect on this starter. Anyone have good pictures to post??
2. Is the starter heat shield in the correct place or do I have to move it back a little and move studs one space over?
3. Brown with yellow stripe wire, where does that go?
http://i67.tinypic.com/1zgarzd.jpg
http://i65.tinypic.com/t8mcsl.jpg
http://i67.tinypic.com/ri9bex.jpg
81dmc
10-28-2016, 12:40 AM
Question on the starter wires and how to position them with headers on. I have a Bosch starter, Josh's s/s exhaust kit, and Hervey's heat shield for starter.
1. Red battery wire, red jump start post wire and brown alternator wire go on top as I have them. Other wire which is white or beige with red stripe connects to the right of it? How about the wire with Green and yellow stripe where does that go? I have seen other pictures of starters and connects right under the beige red wire, but no where to connect on this starter. Anyone have good pictures to post??
2. Is the starter heat shield in the correct place or do I have to move it back a little and move studs one space over?
3. Brown with yellow stripe wire, where does that go?
1. The large, white, red stripe wire is for solenoid activation and connects to the small lug.
The bundled two blue, yellow stripe wires connect to the large lower lug. To install those, buy a 14 awg wire and crimp a ring terminal on one side and a male bullet on the other.
2. I don't know. I don't run one with Josh's Spec I.
3. The brown, yellow stripe wire connects to the alternator. It is for the battery light on the dash.
1batt4u
10-28-2016, 01:11 PM
I figured the brown with yellow stripe wire goes to alternator, I just wanted to be sure.
So the blue yellow stripe wires connect to the lower lug where the wire connects straight to starter? I just want to be sure, don't want to end up damaging or burning something.
Thank you!
DMC5180
10-28-2016, 05:50 PM
I figured the brown with yellow stripe wire goes to alternator, I just wanted to be sure.
So the blue yellow stripe wires connect to the lower lug where the wire connects straight to starter? I just want to be sure, don't want to end up damaging or burning something.
Thank you!
The original Rhone starter had an extra pigtail wire coming from the Solenoid cap. This wire would get energized when the Solenoid was engaged and spun the starter motor. The common thing to do with the smaller starter is to just add a small ring terminal and attach it with the WHITE/RED wire. The doubled Blue/Yellow does to things one wire is the Ignition By-pass relay energize feed, the other is the power feed through the Relay to the Resistor. My guess is the reason the power was sourced the MOTOR SIDE of the solenoid was to minimize the potential voltage drop by using the power of the larger cables versus the starter engagement circuit. Use of either wire placement method is functionally the same.
1batt4u
10-28-2016, 09:13 PM
The original Rhone starter had an extra pigtail wire coming from the Solenoid cap. This wire would get energized when the Solenoid was engaged and spun the starter motor. The common thing to do with the smaller starter is to just add a small ring terminal and attach it with the WHITE/RED wire. The doubled Blue/Yellow does to things one wire is the Ignition By-pass relay energize feed, the other is the power feed through the Relay to the Resistor. My guess is the reason the power was sourced the MOTOR SIDE of the solenoid was to minimize the potential voltage drop by using the power of the larger cables versus the starter engagement circuit. Use of either wire placement method is functionally the same.
So I will attach the Blue/yellow wires with the white/red wire. I was doing some research and read someone else who did that.
Thank you!
DMC5180
10-28-2016, 09:18 PM
That is what DMCMW does. I did it with mine. No issues.
Its your choice. Either method works.
Sent from my iPhone using Tapatalk
1batt4u
10-28-2016, 09:21 PM
That is what DMCMW does. I did it with mine. No issues.
Its your choice. Either method works.
Sent from my iPhone using Tapatalk
Cool! Thank you again!!
DMC5180
10-28-2016, 09:29 PM
Cool! Thank you again!!
On my car, I did not want too remove the bullet connector socket from the harness. I just made a 5 inch connector wire with the ring terminal on one end and female bullet connector on the other.
Your original connector is gone but you could still something similar if wanted.
Sent from my iPhone using Tapatalk
1batt4u
10-29-2016, 05:14 PM
On my car, I did not want too remove the bullet connector socket from the harness. I just made a 5 inch connector wire with the ring terminal on one end and female bullet connector on the other.
Your original connector is gone but you could still something similar if wanted.
Sent from my iPhone using Tapatalk
Ok cool, I will do the same.
Thank you again!
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.