View Full Version : Engine Exhaust Studs
spikeygg
10-29-2016, 01:09 PM
Hi guys, I have found that I'm missing more than half of the exhaust studs on my engine. I guess the guys that built it decided that they didn't need four studs/nuts per exhaust port and just put two on each one. Anyway, I wanted to put them back but obviously I don't have the hardware. So I ordered a few from DeLorean.com but when I compare the studs that are in my engine with the ones that I got from DeLorean.com, they look completely different.
Comparison between two studs:
46923
They are both M7x1.0 and 1.75" long double ended.
My engine stud:
46925
Has symmetric threading on just over 0.5" of each end
DeLorean.com stud:
46924
Has 0.25" threading on the short end and 1" of threading on the long end
I am worried about the number of threads on the short end of the DeLorean.com stud.
Which end goes into the head, short or long? Seems to me that the short end would not be enough threading to really dig in... but I don't know.
P.S. The picture shown on their website is a third variety of stud (http://store.delorean.com/p-6212-stud-m7.aspx) which bothers me because they clearly state: "We like ours best because they are the correct length!" The one in their picture has 0.5" of threading on the short end and 0.75" of threading on the long end. Too bad they didn't send me this one, I wouldn't have this question...
46926
David T
10-29-2016, 01:46 PM
You do not need to put a stud in every hole. This engine was used in many different models and makes of cars so they did that for intercompatablity. The short end always goes into the head. If you are replacing the studs the best ones are PJ Grady's S/S ones but a set is expensive. Best to heat them up before trying to remove them (if you are removing them). Use Never Seize on all exhaust hardware when reassembling.
DMCMW Dave
10-29-2016, 04:59 PM
Factory manifolds only have 2 studs per hole, there is no metal on the cast manifolds to use the other two holes. The "short" end of the stud goes into the head, and those have more threads than the head does. They should not necessarily be pulled tight in the head, just fully engaged. Tightening the nuts on installation will make everything tight enough.
Most aftermarket headers have all 4 holes in the flanges but common practice is to only use two of them, sometimes opposite the original two positinos to avoid having to remove broken studs. Use all four if you want (and can), it's certainly better.
If you were to put the "long" end into the head, it's possible that the nut will tighten down where the threads stop and force the stud out the back of the pocket in the head (leads to oil or coolant leaks!).
1batt4u
10-29-2016, 05:24 PM
So the short ends go in the engine and the long sides stick out to install exhaust headers on them? I bought Rob's s/s studs with copper nuts. I installed the studs with long side in engine.
David T
10-29-2016, 06:02 PM
So the short ends go in the engine and the long sides stick out to install exhaust headers on them? I bought Rob's s/s studs with copper nuts. I installed the studs with long side in engine.
No good. As mentioned if you run out of thread when putting the nut on you will not be clamping the manifold tightly against the head. The gasket will blow out and you will have exhaust leaks. If you try to tighten the nut you will drive the stud into the head causing damage. Take it all apart and insert the shorter threaded end into the head. On most other motors the head is usually tapped course thread and the other end of the stud and the nuts are fine thread so you can't mix it up. Not that way on the PRV.
1batt4u
10-29-2016, 10:55 PM
No good. As mentioned if you run out of thread when putting the nut on you will not be clamping the manifold tightly against the head. The gasket will blow out and you will have exhaust leaks. If you try to tighten the nut you will drive the stud into the head causing damage. Take it all apart and insert the shorter threaded end into the head. On most other motors the head is usually tapped course thread and the other end of the stud and the nuts are fine thread so you can't mix it up. Not that way on the PRV.
Ok thank you!! :thumbup2: Will switch them around.
spikeygg
10-30-2016, 10:03 AM
Thanks guys, these posts were very helpful.
1batt4u
11-01-2016, 11:48 AM
What would be the torque on these nuts 12 ft lbs? What tightening order?
David T
11-01-2016, 01:14 PM
What would be the torque on these nuts 12 ft lbs? What tightening order?
Closer to 10 ft/lbs and that's if you can get a torque wrench on them. Good practice is to start in the middle and evenly work towards both ends.
DMC5180
11-01-2016, 09:52 PM
All M7 bolts/nuts are 11 Ft lb.
The only listing in the Shop manual given for M7. X 1.0 is timing cover bolts, 11 Ftlb., but it essentially applies to all the other M7 hardware used on the engine. ( rocker cover, intake bolts, W & Y - pipes, exhaust manifolds etc.
Sent from my iPhone using Tapatalk
David T
11-02-2016, 11:20 AM
Most torque measuring devices cannot measure ft/lbs accurately that low (10-12 ft/lbs). You will need to torque it to N/M or in/lbs. The problem is many of the fasteners are not reachable by the torque wrench so you must do them as accurately as you can by hand with a box wrench.
DMC5180
11-02-2016, 11:29 AM
Most torque measuring devices cannot measure ft/lbs accurately that low (10-12 ft/lbs). You will need to torque it to N/M or in/lbs. The problem is many of the fasteners are not reachable by the torque wrench so you must do them as accurately as you can by hand with a box wrench.
Agreed. Most every spec I use at work that is less than 17 ft lbs. is called out in Pound inches. Most all of our inch pound torque wrenches are 40-200 inch pound scale.
Sent from my iPhone using Tapatalk
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.