PDA

View Full Version : Fuel Dowty Seals for K-Jet?



81dmc
10-31-2016, 05:17 PM
Can oil-rated dowty washers be used in place of the factory copper washers? Can they withhold the pressure?

DMCVegas
10-31-2016, 05:50 PM
I would not think that they would be an appropriate substitute, no.

Pressure wouldn't be my concern here. They might be fine for something such as water, some gases, & various oils, but they seem to have warnings that they're only safe for "low octane fuels" with no indicator of what that specific octane range is. There is also no mention of distillates or alcohols which is a concern since ethanol can tear up rubber not meant for it in a heartbeat.

The malleability of the metal would be the other large concern. Standard Crush Washers are intended to form a precise, tight seal that will not fail unless the mating surfaces are broken. But Dowty seals may be too hard to properly let the Banjo Fittings sink in, and may even damage them. They may also have a finite lifespan thanks to their rubber components. They are great for supply lines that have a wide fluctuation of line pressures (and more benign contents), but that's not something to really be concerned about with K-Jetronic.

I'd just stick with stock pieces here.

81dmc
11-02-2016, 10:14 AM
Well, it seems they are made with nitrile (Buna-N). I would think that would be fine. Also, the washers are aluminum, which tends to crush better than our original copper washers. However, this would mean replacement would be necessary every time the mixture unit is removed.

David T
11-02-2016, 11:14 AM
The joints were designed to use the copper seals. I see no advantage to using anything else. You are literally "Playing with Fire" here so be careful with your choices.

Dangermouse
11-02-2016, 12:34 PM
Also, the washers are aluminum, which tends to crush better than our original copper washers.

I always thought that copper crushed better. Aren't copper washer designed for such an application hollow to allow for better crushibility? If that's a word.

David T
11-02-2016, 01:00 PM
I always thought that copper crushed better. Aren't copper washer designed for such an application hollow to allow for better crushibility? If that's a word.

The copper seals are not affected by Ethanol. The copper crushes just enough. The torque is a very critical amount. Not enough and you don't get the proper crush and seal, too much and you break the hollow bolt. Copper is soft but it work-hardens easily. That means once you use a copper seal it gets hard. If you try to reuse it you must tighten it a LOT more to get it to crush. If you do try to over-tighten the hollow bolt to reuse it you break them. Bottom line is never reuse a copper seal. If you must reuse one they can be annealed by heating them up and cooling slowly. Not worth the trouble.

DMCVegas
11-02-2016, 02:00 PM
Here is the link to the chart I was referencing:

http://www.potterassoc.com/pdf/bonded_seal_information_and_sizing_chart.pdf

I'm a bit concerned there with the temperature thresholds too. Again though is the concern of ethanol, even when used against nitrile rubber. Which according to this chart right here, is something you should be wary about:

http://mykin.com/rubber-chemical-resistance-chart-3

The thing here is that you don't really pull banjo fittings in an automotive application apart all that much. On a properly functioning vehicle that is used regularly (don't think solely of a DeLorean, think of all the Volvos, Renaults, and motorcycles the world over that use these fittings), you don't exactly rebuilt the fuel and hydraulic braking systems on a regular basis. For the most part, they pretty much take care of themselves. So there isn't a concern about worn areas. By contrast take an oil change for example. That is something you WILL do on a regular basis, so the use of a dowty seal on the drain plug would absolutely benefit it that.

Aluminum vs. copper? I've purchased crush washers directly from a BOSCH supplier in the past that were aluminum, and they worked just fine. But they were however intended to work as K-Jetronic seals, so their alloy content may have been adjusted accordingly to properly function with the purpose they were intended for.

The big question though is one of what exactly do you hope to gain from using these dowty washers over traditional BOSCH crush washers? Centering washers has never been a problem when you use the appropriate ones. And if you're looking for something that might be reusable, a dowty washer isn't going to provide that either since the function of the seal is based upon crushing the washers and sinking the lips of the fittings into the washer.

And if you're trying to use a dowty washer because it saves money... Please don't. There are lots of ways to save money, but this is not where you want to try and do that.

Bitsyncmaster
10-15-2025, 02:36 PM
I tried these Dowty washers on a few of my 8 mm banjo bolts.

https://www.ebay.com/itm/352477754837?mkevt=1&mkpid=0&emsid=e11996.m144671.l197929&mkcid=7&ch=osgood&euid=e93bbf2155da46dca7b046baca9a1e7c&bu=43153455412&exe=0&ext=0&osub=-1%7E1&crd=20251014065337&segname=11996

I torqued them to 108 inch/lbs which is the max recommended by our service manual. One broke, the rest all tore up the rubber seal. The problem is our banjo bolts have the sealing surface diameter almost smaller then where the metal on the washers is. I would have no problem using these on a normal sized bolt. Not good for our banjo bolts.