Log in

View Full Version : Electrical Strangeness with indicators...



Lwanmtr
11-03-2016, 08:15 PM
Ok, I got my new indicator switch from DMC and now I have turn signals...yaay....

But wait a minute.....

All four side markers are flashing too..

Anyone have an idea what could cause that, where to look?

Thanks

Jonathan
11-03-2016, 09:50 PM
Did your car get this mod that allows the side marker lights to flash with the turn signals? Normally they don't flash and only come on with the headlights. Maybe something screwy is going on with either the hazards switch, the headlight switch, your turn signal stalk, or some combination of those?

Lwanmtr
11-03-2016, 10:04 PM
Hehe...

Hazard switch is new, just got turn signal switch today, so its new...headlight switch works fine (mostly)...hehe.

As for a mod..i have no idea, anything is possible, given some of the things I seen that convinced me PO was on some rally good drugs..hehe.

Talked to Toby and he said it could be I put the wrong lights into the sockets..I guess the front and rear ambers are different in the LED's..so I'll prolly check that tomorrow..or a bit later if I get a moment.

Lwanmtr
11-03-2016, 10:42 PM
Well...dang...the lights are in the correct sockets...lol

Ron
11-04-2016, 02:41 PM
Remove the front marker bulbs only to see if the mod mentioned might be involved.
...wondering if the tail lights are acting like the marker lights, as they should be??

81dmc
11-04-2016, 04:23 PM
Have you upgraded to LEDs?

I once used LEDs from Autozone with the DeLorean and my pickup truck. Eventually, I noticed the LEDs caused both vehicles to flash all running lights when I hit the brakes or when the turn signals were activated.

I never figured out why it happened...

Lwanmtr
11-04-2016, 04:43 PM
Not sure what the mod is you talk about it...

In any case, all the indicator and marker lights are LED's..got them from DMC, so they're the right ones. Yeah, the tail lights are working as they should be too..hehe.

Im perplexed... :banghead:

Lwanmtr
11-06-2016, 07:03 PM
Im at a complete loss...checked bulbs, etc. I have the battery disconnected for the moment, until I make sure I plugged the new actuators in the right spot...but Im thinking of removing the flasher swtich to see if that makes a difference...thought its a new swtich, so I kinda doubt it.

Bitsyncmaster
11-06-2016, 07:27 PM
There was a wiring modification some people do to get the side markers to flash with the turn signal. But that only worked with incandescent bulbs.

You would need to see if you can restore the original wiring if that modification was done.

Lwanmtr
11-06-2016, 07:42 PM
I have no way of knowing if the modification was done.

DaraSue
11-07-2016, 10:18 AM
You checked all the fuses and relays too, right? I vaguely remember having a problem similar to what you're describing in my CRX (this was about 20 years ago) and the issue was a bad relay (the one that controlled the turn signals and hazard lights).

Bitsyncmaster
11-07-2016, 11:10 AM
I have no way of knowing if the modification was done.

You would need to follow the wires starting at the side light socket back. If you don't see any modification back to the main harness then you probably don't have the modification installed.

Jonathan
11-07-2016, 12:57 PM
I have no way of knowing if the modification was done.


You would need to follow the wires starting at the side light socket back. If you don't see any modification back to the main harness then you probably don't have the modification installed.

Look for something resembling this: http://www.dmcnews.com/Techsection/markerflash.html

DrJeff
11-07-2016, 02:49 PM
There was a wiring modification some people do to get the side markers to flash with the turn signal. But that only worked with incandescent bulbs.

You would need to see if you can restore the original wiring if that modification was done.

Dave, I'm assuming this is because of the D in LED, diode. The mod works because incandescent bulbs don't care about the direction of current flow. Is there some other way to wire this or select a different type of LED that could get around the problem?

Jeff

DMC5180
11-07-2016, 03:58 PM
In you first post, you say, all 4 side markers are flashing too. Please clarify All at once or independent L & R with turn signal? If with turn signal do the lights alternate the flash? Signal ON , marker OFF and Signal OFF, marker ON. Do the markers flash IF the Signal bulbs are removed? Your Looking for back feeding across the front Park/turn light sockets. The other question is, did it do this before you replaced the turn signal switch?


Sent from my iPhone using Tapatalk

Nate88
11-07-2016, 04:12 PM
I'm also interested in why this modification doesn't work with LED's? I have converted all of the exterior bulbs besides the headlights to LED's which would include the front turn signal lights and side marker lights. I also have the correct LED flasher module (I got the complete kit from DMCH). This is a mod I'm interested in (more on the front than rear) hoping it will help with visibility since a lot of newer cars have side turn signal lights on the mirrors or fenders.

Lwanmtr
11-07-2016, 04:29 PM
In you first post, you say, all 4 side markers are flashing too. Please clarify All at once or independent L & R with turn signal? If with turn signal do the lights alternate the flash? Signal ON , marker OFF and Signal OFF, marker ON. Do the markers flash IF the Signal bulbs are removed? Your Looking for back feeding across the front Park/turn light sockets. The other question is, did it do this before you replaced the turn signal switch?

All four flash, reguardless of left or right direction selected.
Havent tried with the bulbs removed...you're talking about the front indicators, yeah?
Before I replaced the turn signal switch, there was nothing...the switch was dead when I got the car.

Dara, All my fuses are good..though the fuse box could use a replacement..hehe.

I wouldnt mind if only the flash occured on the selected side.

I'll dig a little later today and check the front harness for possible shennanigans.

DMC5180
11-07-2016, 04:43 PM
Yes front indicator sockets.

What headlight switch do you have ? original or DMCH replacement. It seems like something is crossed up.

Check the connectors on the back of the headlight switch for correct position and orientation, I don't recall if they can be installed 180 out.

Sent from my iPhone using Tapatalk

Lwanmtr
11-07-2016, 04:54 PM
I'll assume original headlight switch

DMC5180
11-07-2016, 05:04 PM
This almost sounds like a connector is mis-pinned or perhaps incorrectly installed. Have you ever pulled the connector off the headlight switch?


Sent from my iPhone using Tapatalk

Lwanmtr
11-07-2016, 05:14 PM
Yeah, I've had the headlight switch out..all the connectors looked good and the switch had no heating evidence.

DMC5180
11-07-2016, 05:33 PM
I just checked an old headlight switch connector to see if it's possible to install in more than one way. It is Not. Do your headlights function properly?


Sent from my iPhone using Tapatalk

Lwanmtr
11-07-2016, 05:42 PM
Yep, all the lights work properly, so do hazards and turn indicators...just the markers being weird. One thing I note is that they arent getting full power, the markers are dim when they are flashing like that...but bright when turned on normally.

DMC5180
11-07-2016, 05:47 PM
Okay, that sounds like back feeding. Definitely try removing the front indicator bulbs.


Sent from my iPhone using Tapatalk

Bitsyncmaster
11-07-2016, 06:23 PM
Dave, I'm assuming this is because of the D in LED, diode. The mod works because incandescent bulbs don't care about the direction of current flow. Is there some other way to wire this or select a different type of LED that could get around the problem?

Jeff

Not sure if a bi-directional LED would work with that modification. It also depends on the low resistance of the light bulb when not powered (just lights on, no turn signal).

I installed a little circuit that drives each side marker using the lights and blinkers as signals to that circuit. All four of my side lights have that circuit since I have all LEDs. I think it was one IC to make two circuits work. It needed a constant power wire also.

http://dmctalk.org/showthread.php?2792-Headlight-ground-wires&highlight=side+blinker

Lwanmtr
11-07-2016, 09:05 PM
Ok....I removed the front indicator lights one at a time..and it seems theres something in the front harness going on cause with the bulbs out I get only the rear indicators flashing.

I'll try and dig into that tomorrow and see if its a fault with the harness or if that mod was done.

DMC5180
11-07-2016, 09:08 PM
Is there any corrosion present in the those front sockets?

Also try reinstalling the OEM 1157 bulbs. Make sure the nubs on the side of the bulbs are in the correct phase position too. They are not the same height on each side. Wait is it possible you installed the wrong type LED in the front sockets. If that were to happen and you used a 1156 style LED in the front Sockets, the center contact of the 1156 base could bridge the Double contacts in socket base. This would cross feed the Park/tail and side markers.

Sent from my iPhone using Tapatalk

Lwanmtr
11-07-2016, 09:41 PM
Sockets look ok. The correct LEDs are in the front (two contacts). The original bulbs were dead.

DMC5180
11-07-2016, 09:49 PM
Just to confirm, with the Front LEDs removed, all the remaining lights functioned normally?

When you get back to it, try reinstalling just one front LED at a time, perhaps you can isolate a side that's causing the issue. Those front sockets can cause weird things to happen.


Sent from my iPhone using Tapatalk

Lwanmtr
11-07-2016, 09:52 PM
yerp...lol

Lwanmtr
11-08-2016, 07:43 PM
Well, If I pull either indicator light and hit the turn signal for that side, the sides dont flash, so I'm sure its something there...if it was the fuses shorting, it would happen all the time, same with a short in the harness (I think).

I took a couple pics of the connectors for the fron indicators....do the wires look right?

4723747238

81dmc
11-08-2016, 07:52 PM
Well, If I pull either indicator light and hit the turn signal for that side, the sides dont flash, so I'm sure its something there...if it was the fuses shorting, it would happen all the time, same with a short in the harness (I think).

I took a couple pics of the connectors for the fron indicators....do the wires look right?

4723747238

Try using a regular bulb and see if that fixes it.

Lwanmtr
11-08-2016, 07:55 PM
I'll have to see if I have them...most of the lights were bad on the car when I got it.

DMC5180
11-08-2016, 07:56 PM
What is covering the right wire in the second photo? (white connector)

It wouldn't hurt to unplug each socket connector and reconnect. This may scratch through old tarnish on the terminals.


Sent from my iPhone using Tapatalk

DMC5180
11-08-2016, 07:59 PM
I'll have to see if I have them...most of the lights were bad on the car when I got it.

1157 bulbs are about $3 for a 2 pack most places. It won't break the bank for diagnostic purposes. [emoji6]


Sent from my iPhone using Tapatalk

DMC5180
11-08-2016, 08:10 PM
Also, with each socket assembly disconnected, do continuity checks of the terminals and socket contacts. Each terminal should only have one continuity contact in the socket.


Sent from my iPhone using Tapatalk

Lwanmtr
11-08-2016, 08:14 PM
Ok, found one of the originals that was good.

Putting it into the left (driver side) socket fixes the problem...even swapped the sockets themselves, and its on the left side.
Its not a short, Im sure...as that would make it do it even with a regular bulb....so lil more confused...unless its the wires on the connector are wrong.

I couldnt tell you for sure (since I didnt do it), but it looks like heatshrink stuff covering that wire, someone mighta repaired it.

DMC5180
11-08-2016, 08:20 PM
What happens if you put one LED in the RIGHT socket with the LH socket unplugged?


Sent from my iPhone using Tapatalk

Lwanmtr
11-08-2016, 08:34 PM
Ok...I stand corrected....had I put the regular bulb in the right side again and it started flashing the sides..so I jiggled it a little and the sides stopped...so it seems that I'll need to replace that socket. That socket was on the left, so when i swapped the sides, and it worked it led me to beleive the left side on the harness was bad...but seems I was just getting lucky with the old bulb, til this last time.

DMC5180
11-08-2016, 08:38 PM
It could be that the coil spring under the contact insulator is somehow bridging both wires. Replacing the socket(s) is the best way to go.

Glad you were able to work through it to a resolution.


Sent from my iPhone using Tapatalk

Lwanmtr
11-08-2016, 08:45 PM
Yeah I'm guessing the spring or something, cause it doesnt spring like the other socket does.

Im glad I got it narrowed down too...was getting really confusing...lol

Gotta get ahold of Toby and see if they sell that socket seperate...dmc parts store only shows the whole assembly with the lens n stuff

jerrysony
06-06-2020, 06:49 PM
Have you upgraded to LEDs?

I once used LEDs from Autozone with the DeLorean and my pickup truck. Eventually, I noticed the LEDs caused both vehicles to flash all running lights when I hit the brakes or when the turn signals were activated.

I never figured out why it happened...I just upgraded to leds, new flasher unit and having same issue. Rear Led turn/hazard bulb doesn't even lights. Before the upgrade, these incandescent bulbs already received very low power, even at night you could barely notice they were blinding. Any advice?

Enviado desde mi SM-G975F mediante Tapatalk

81dmc
06-06-2020, 07:04 PM
I just upgraded to leds, new flasher unit and having same issue. Rear Led turn/hazard bulb doesn't even lights. Before the upgrade, these incandescent bulbs already received very low power, even at night you could barely notice they were blinding. Any advice?

Enviado desde mi SM-G975F mediante Tapatalk

If you had the issue before with incandescents, check your tail light circuit board. You may need a newer updated one. Also check the tail light plug for corrosion, and check the black connector at the bulkhead in the engine compartment, you may have corrosion there as well.

Good luck

jerrysony
06-06-2020, 09:40 PM
Thanks 81dmc, I'll try that. I also observed that the seat belt warning light keeps blinking while in the road. (My car has no buzzer). Could a bad ground on that relay be the cause of low voltage on the rear marker lights and the blinking?

Enviado desde mi SM-G975F mediante Tapatalk