View Full Version : General DMC Dealership sign delivered today!
dmruschell
11-04-2016, 12:41 AM
I just purchased a DMC dealership sign today! I've been wanting one for a while and finally found one. Of course, there are a few things that need to be fixed and was wondering if anyone here has had any experience working on these signs. The plexiglass on the top needs to be replaced. I'd also like to replace the fluorescent light setup with LEDs. However, if anyone has successfully gotten the fluorescent light setup working, I'd be interested to see if I can get it working in the mean time. Thanks in advance for any guidance.
47120
dmruschell
11-04-2016, 01:10 AM
Have you considered growing a mustache and consulting the workshop manual?
Sometimes, when I shave, I leave just the mustache and see what it would look like. I immediately decide that it looks terrible and shave it off, too.
I didn't think that the Workshop Manual had any info on the sign, though I guess it would make sense if the Workshop Manual was meant to help dealerships work on the cars.
EDIT: You should update the cars in your signature. :)
louielouie2000
11-04-2016, 09:25 AM
Congrats on landing that dealership sign! I've been watching it on eBay and forcing myself not to buy it! I'm glad it went to someone in the community. Please keep us updated on its restoration.
Delorean Industries
11-04-2016, 09:55 AM
If you want to keep it original I have six or seven of these in storage. The ones we have in use have been converted over to LED's. I kept the stock components though.
Nicholas R
11-04-2016, 09:56 AM
However, if anyone has successfully gotten the fluorescent light setup working, I'd be interested to see if I can get it working in the mean time. Thanks in advance for any guidance.
47120
I helped Cliff Schmucker hang his and get his working. If I recall correctly, there are either 2 or 3 different lighting zones inside. I think the "DMC," "DeLorean," and "Motor Cars" are each their own zone. it was 2010 so I can't remember for sure about the exact zones.. Surprisingly, his lighting seemed to work pretty well. We did testing to make sure it worked, and it seemed as though everything was great. With the lighting working, we went ahead and hung the sign in his workshop. Unfortunately, when we were all finished, we turned it on, and only one zone lit up; the DMC. The "DeLorean Motor Cars" did not light up at all. We couldn't figure out why because when we tested it on the ground it worked great. The only thing we could think was that when we were testing it on the ground, the sign was upside down so we could get to the bottom access panel (see the picture below of Cliff and removing the panel). When we flipped it over, something must have happened and part of the sign stopped working.
Luckily Cliff was an electrical engineer so it didn't really phase him. The pain was just that now we had to work on the sign with it 25 feet in the air using a fork lift man-basket. We swapped out the 30 year old ballasts for the fluorescent lights, and sure enough, all zones lit up perfectly. Fluorescent technology has improved since the 80s. I think the ballasts we swapped in were about 1/4th the size of the ones we pulled out, so doing so is possible. The hardest part was accessing them. I think we had to get the end panels off in order to access them. Hope this helps!
4712147122
Dangermouse
11-04-2016, 11:15 AM
Luckily Cliff was an electrical engineer so it didn't really phase him.
:bigclap:
Nicholas R
11-04-2016, 11:21 AM
:bigclap:
Haha, to be clear, it did not "faze" or "phase" him, :wink:
dmruschell
11-04-2016, 12:15 PM
If you want to keep it original I have six or seven of these in storage. The ones we have in use have been converted over to LED's. I kept the stock components though.
If converting it to LEDs is not difficult, that's probably what I'd prefer to do. I'm still considering all of the options, though. I'd be interested to know how you do it, since I've seen your signs and they look great. Given your products and how well they're engineered, I'm also guessing you've figured out a few tricks along the way.
dmruschell
11-04-2016, 12:18 PM
I helped Cliff Schmucker hang his and get his working. If I recall correctly, there are either 2 or 3 different lighting zones inside. I think the "DMC," "DeLorean," and "Motor Cars" are each their own zone. it was 2010 so I can't remember for sure about the exact zones.. Surprisingly, his lighting seemed to work pretty well. We did testing to make sure it worked, and it seemed as though everything was great. With the lighting working, we went ahead and hung the sign in his workshop. Unfortunately, when we were all finished, we turned it on, and only one zone lit up; the DMC. The "DeLorean Motor Cars" did not light up at all. We couldn't figure out why because when we tested it on the ground it worked great. The only thing we could think was that when we were testing it on the ground, the sign was upside down so we could get to the bottom access panel (see the picture below of Cliff and removing the panel). When we flipped it over, something must have happened and part of the sign stopped working.
Luckily Cliff was an electrical engineer so it didn't really phase him. The pain was just that now we had to work on the sign with it 25 feet in the air using a fork lift man-basket. We swapped out the 30 year old ballasts for the fluorescent lights, and sure enough, all zones lit up perfectly. Fluorescent technology has improved since the 80s. I think the ballasts we swapped in were about 1/4th the size of the ones we pulled out, so doing so is possible. The hardest part was accessing them. I think we had to get the end panels off in order to access them. Hope this helps!
4712147122
That does help a bit, so I know what I'm looking for. I'm not an electrical engineer, but I did replace the ballasts in my garage and converted the lights to the newer style thinner bulbs. 7 fixtures, 2 ballasts each means that I can almost do that job with my eyes closed lol. So, replacing or updating the ballasts wouldn't be a huge job if that's the direction I end up going.
BLWNAWY
11-04-2016, 02:25 PM
I helped Cliff Schmucker hang his and get his working.
4712147122
Is that the one Cliff bought from me? That crate base sitting next to it looks very familiar. Great looking installation. For the record I had a commercial sign company go through that sign when I bought it (from Shreveport LA) in the late 80's, and had it lighted in my shop through 1998. When I moved to my current place I had it mounted on the wall, but no longer plugged in as power wasn't close by. Wish I still had it, but in its place is a 16' long shelf full of BLWNAWY parts......
Nicholas R
11-04-2016, 05:06 PM
Is that the one Cliff bought from me? That crate base sitting next to it looks very familiar. Great looking installation. For the record I had a commercial sign company go through that sign when I bought it (from Shreveport LA) in the late 80's, and had it lighted in my shop through 1998. When I moved to my current place I had it mounted on the wall, but no longer plugged in as power wasn't close by. Wish I still had it, but in its place is a 16' long shelf full of BLWNAWY parts......
Actually I think it is. If I recall correctly, he bought this sign from you along with a big lot of DeLorean parts right?
Here's how you'll know for sure, look at this picture. Cliff's sign still had one side that the original protective plastic had never been removed from. He said that wherever it was shown had one side against the wall so the plastic was never removed. Seems consistent with you having it mounted on the wall. When we were prepping the sign for hanging, we removed the plastic and put that side 'outward,' or at least the more viewed side. Did your sign still have the protective plastic on it?
47127
We spent a lot of time hand polishing that sign to get all of the stainless shining really nicely. He was very proud of it. I remember he asked me to do the trigonometry needed so that we could figure out exactly where to drill the holes in his roof support beams. I was pretty nervous drilling holes in his roof, hoping they'd line up correctly. Luckily everything went great (with the exception of having to replace the ballasts)!
That sign overlooked a lot of great tech days at Cliff's place
47128471294713047131
Bitsyncmaster
11-04-2016, 05:29 PM
I have been converting some of my florescent lights to standard bulb sockets so I can install LEDs into them. I do that with those strange type florescent bulbs. But my kitchen lights I was able to buy LED replacement bulbs that are almost plug and play (you remove the ballast transformer).
blueshark66
11-04-2016, 05:34 PM
I just purchased a DMC dealership sign today! I've been wanting one for a while and finally found one. Of course, there are a few things that need to be fixed and was wondering if anyone here has had any experience working on these signs. The plexiglass on the top needs to be replaced. I'd also like to replace the fluorescent light setup with LEDs. However, if anyone has successfully gotten the fluorescent light setup working, I'd be interested to see if I can get it working in the mean time. Thanks in advance for any guidance.
47120
Very cool! Congrats! My wife will not be happy you have planted this idea in my head...
BLWNAWY
11-04-2016, 07:48 PM
Actually I think it is. If I recall correctly, he bought this sign from you along with a big lot of DeLorean parts right?
Here's how you'll know for sure, look at this picture. Cliff's sign still had one side that the original protective plastic had never been removed from. He said that wherever it was shown had one side against the wall so the plastic was never removed. Seems consistent with you having it mounted on the wall. When we were prepping the sign for hanging, we removed the plastic and put that side 'outward,' or at least the more viewed side. Did your sign still have the protective plastic on it?
Yep that's it. The sign was brand new when I got it, still in the original box. Unfortunately in my last small shop it was subject to a lot of overspray etc. I think what Cliff got from me was a bunch of memorabilia. Toby Peterson got my parts, which led to the formation of DeLorean Parts Northwest and his DMCNW shop. Glad to see the sign getting the respect it deserved.
dmruschell
11-05-2016, 01:29 AM
I have been converting some of my florescent lights to standard bulb sockets so I can install LEDs into them. I do that with those strange type florescent bulbs. But my kitchen lights I was able to buy LED replacement bulbs that are almost plug and play (you remove the ballast transformer).
I was thinking thatit might be easier to just use the LED tube bulbs and remove the ballasts. I was debating doing that in my garage, but with 7 fixtures that use 4 bulbs each, it would have been a LOT more expensive. The difference in price of the bulbs really ads up when multiplied by 28, especially when the fluorescent were available in bulk and the LEDs weren't. 3 bulbs in a sign wouldn't be so bad. I can probably use the original bulb holders and just run new wires.
Bitsyncmaster
11-05-2016, 06:44 AM
I was thinking thatit might be easier to just use the LED tube bulbs and remove the ballasts. I was debating doing that in my garage, but with 7 fixtures that use 4 bulbs each, it would have been a LOT more expensive. The difference in price of the bulbs really ads up when multiplied by 28, especially when the fluorescent were available in bulk and the LEDs weren't. 3 bulbs in a sign wouldn't be so bad. I can probably use the original bulb holders and just run new wires.
I bought a six pack of these for $45 from this guy. But I did not see that offer anymore. I highly recommend these bulbs because the 6500 k light is very bright. Much brighter than the old 40 watt fluorescent bulbs.
https://www.amazon.com/gp/product/B012AHPAZ0/ref=od_aui_detailpages00?ie=UTF8&psc=1
I replaced my garage fluorescent with standard bulb sockets and use LED bulbs. You can also get bulb socket doublers if you want more light in that area. Then you use two LED bulbs in that socket.
Delorean3610
11-05-2016, 12:48 PM
My dad's former business sign was hung in 1978, for the 34 years that sign was hanging it never needed a bulb replaced.
On topic: there are fluorescent tube style LED bulbs now.
DMC-81
11-05-2016, 01:10 PM
On topic: there are fluorescent tube style LED bulbs now.
Cool! I didn't realize that. Do they require a ballast, etc and can you retrofit an existing fluorescent fixture? I'd be interested in converting in time...during the course of my restoration, I had to replace the 8 tubes 3 times, and the 4 ballasts once in my garage.
Delorean3610
11-05-2016, 02:22 PM
Cool! I didn't realize that. Do they require a ballast, etc and can you retrofit an existing fluorescent fixture? I'd be interested in converting in time...during the course of my restoration, I had to replace the 8 tubes 3 times, and the 4 ballasts once in my garage.
https://www.earthled.com/blogs/light-2-0-the-earthled-blog-led-lighting-news-tips-reviews/33135492-how-to-buy-t8-and-t12-led-fluorescent-replacement-tubes
Try this link.
dmruschell
11-05-2016, 03:38 PM
Cool! I didn't realize that. Do they require a ballast, etc and can you retrofit an existing fluorescent fixture? I'd be interested in converting in time...during the course of my restoration, I had to replace the 8 tubes 3 times, and the 4 ballasts once in my garage.
They do not require a ballast and you can reuse the fixture. You have to eliminate the ballast so that the bulbs themselves receive 120v.
dmruschell
11-05-2016, 03:43 PM
Update:
I removed the broken plexiglass and the piece that wasn't glued on well behind the DE. I was also able to get a good look at the fluorescent fixtures, ballast housing, and construction of the sign. My current plan is to get a friend help me lay the sign in its back and completely remove the front panel. That way, I can get easy access to the wiring and front panel. That should make refurbishing the front and wiring much, much easier. Many of the rivets holding the front panel on have already been drilled out and replaced with screws, so it should be relatively easy. I just don't want to turn it over by myself lol. I'll take many pictures once that's done so anyone following in my footsteps will have something to look at.
Bitsyncmaster
11-05-2016, 03:47 PM
They do not require a ballast and you can reuse the fixture. You have to eliminate the ballast so that the bulbs themselves receive 120v.
The ballast uses about 40 watts of power in a four foot four lamp fixture. So with the old 40 watt tubes you use 200 watts of power.
With my 22 watt LED tubes I now only use 88 watts.
Some of the LED tubes say you can leave the ballast installed and just plug and play. But how much power is wasted in the ballast running LEDs I don't know.
dmruschell
11-05-2016, 10:46 PM
I helped Cliff Schmucker hang his and get his working. If I recall correctly, there are either 2 or 3 different lighting zones inside. I think the "DMC," "DeLorean," and "Motor Cars" are each their own zone. it was 2010 so I can't remember for sure about the exact zones.. Surprisingly, his lighting seemed to work pretty well. We did testing to make sure it worked, and it seemed as though everything was great. With the lighting working, we went ahead and hung the sign in his workshop. Unfortunately, when we were all finished, we turned it on, and only one zone lit up; the DMC. The "DeLorean Motor Cars" did not light up at all. We couldn't figure out why because when we tested it on the ground it worked great. The only thing we could think was that when we were testing it on the ground, the sign was upside down so we could get to the bottom access panel (see the picture below of Cliff and removing the panel). When we flipped it over, something must have happened and part of the sign stopped working.
Luckily Cliff was an electrical engineer so it didn't really phase him. The pain was just that now we had to work on the sign with it 25 feet in the air using a fork lift man-basket. We swapped out the 30 year old ballasts for the fluorescent lights, and sure enough, all zones lit up perfectly. Fluorescent technology has improved since the 80s. I think the ballasts we swapped in were about 1/4th the size of the ones we pulled out, so doing so is possible. The hardest part was accessing them. I think we had to get the end panels off in order to access them. Hope this helps!
4712147122
Nicholas,
Do you remember how you attached the sign from above? I'm planning to mount the sign on the back wall of my garage and am debating different ways to do it. One way is to hang it form the ceiling. Most people use chains, but that also means I have to leave the top panel off or figure out a way around that. I could also leave the back panel off and use hooks or something else protruding from the wall.
The third way I'm considering is the simplest. I'd follow in Marc Levy's footsteps and not use the frame or lighting at all. The following pictures describe it more easily than I can with words.
http://www.deloreanmidatlantic.com/scrapbook/members/levy/P1010014a.jpg
http://www.deloreanmidatlantic.com/scrapbook/members/levy/P1010015a.jpg
I'd rather mount the whole sign, frame included to the wall, as I like the big, industrial look of the thick frame. But, how Marc hung his is quite simple, since there's a lot less weight to worry about supporting.
dmruschell
11-08-2016, 09:32 PM
Update: I removed the side and front panels and started investigating the wiring. It shouldn't be difficult to reword. I bought four 4 foot LED bulbs made to use a T8 ballast and a ballast. Of course, I didn't measure the bulb socket lengths and none are 4 feet long. Grr. Does anyone know what size bulbs go into the fixtures in the sign? I measured 3 at 56 inches long and one at 68 inches long. Neither seem to correlate to standard sizes.
I have replacement plexiglass/acrylic on the way and will start refurbishing the sign when that is alltogether.
I also found that my sign appears to originally be a bottom-mount sign. I'm going to try and figure something out other than hanging it from a chain so that I can keep the top cover on.
47239
acaciolo
11-09-2016, 12:16 AM
i was going to convert mine to leds, but i decided to keep it original with the unused fluorescents that came with it. The only thing i did was switch out the loud magnetic ballast to a new electronic one. Easy to do, no buzz, and works great.
tony c.
dmruschell
11-11-2016, 12:40 AM
Update: I figured out how I'm going to hang the sign. I drilled a hole in the outer L beam where the original mounts are/would be. On the underside, I placed another L beam for extra strength and drilled a matching hole. Through both holes will be a screw eye bolt with nuts and washers on each side. Those nuts and washers will also keep the extra L beam secured in place. The L beams should want to bend in opposite directions if they're at the limit of their capability, but this setup should be overkill for the loads involved. These pictures probably give a better idea of the setup than my explanation.
47259
47260
I also figured out my lighting setup thanks to a friend who found what T12 bulbs originally went in the signs. I'll post that info and what I'm doing when I'm at my computer.
dmruschell
11-11-2016, 01:52 AM
Update: The lights that came with the DMC light are T12 fluorescent bulbs with an R17d base. The R17d base makes them a bit difficult to find. 3 of them are 60 inches (5 feet) long and the 4th is 72 inches (5 feet) long. I was sent a link to the correct bulbs by a friend:
http://www.elightbulbs.com/Sylvania-25176-F72T12-CW-HO-Straight-T12-Fluorescent-Tube
http://www.elightbulbs.com/Sylvania-25126-F60T12-CW-HO-Straight-T12-Fluorescent-Tube
This allowed me to figure out what I want to do for my setup. I was able to find an adapter that allows use of a standard medium bi-pin G13 bulb with an R17d base. Here's the link to what I purchased:
https://www.prolighting.com/prolight-bi-pin-to-ho-end-cap-socket-adapter-g13-to-r17d.html
This opened up my options. There are LEDs available in the correct lengths that will fit with that adapter, but I couldn't find an LED that would still be compatible with using a ballast. I also couldn't find LEDs in the correct lengths that had one side hot and the other side neutral; they all had the different wires on one end. Not that that's a big deal, but with the color coding of the wires, it would be easier to keep track of what wire in the ballast compartment goes where if the hot and neutral were on opposite sides of the tube. So, I've decided to go with standard T8 bulbs. If they ever stop working, I can easily find replacement bulbs instead of having to make sure I get an LED that is wired the same way as the previous bulb. Standardized is good. T8 bulbs also don't flicker like T12 bulbs tend to. Some people don't notice, but it drives me nuts. No buzz is also a plus. These are the bulbs that I decided on:
https://www.lightbulbs.com/product/ge-40081
https://www.lightbulbs.com/product/ge-62573
I'll update once I get the bulbs and adapters and get everything installed.
The next step after lights is cosmetics. The acrylic panels should be arriving soon and I need to decide what black to use. I had read somewhere that they were painted a satin black, but it looks like flat black to me. I'm also debating if I'm going to try and fix the dents in the stainless or leave them.
dmruschell
11-15-2016, 11:57 PM
Update: The T8 lights I ordered were too long, even though they're listed as the same size as the ones my friend said worked. I'm going to order the T12s my friend said worked for him and see if they'll fit my sign.
I did make progress on the actual sign, though. All of the plexiglass has been replaced/repaired and cleaned. Next is paint.
47397
dmruschell
11-19-2016, 11:18 PM
Update: I have working lights!
After my previous update, I discovered that the DMC sign used High Output (HO) tubes. They have a different connector and are different lengths than standard tubes. So, just adapting the connector won't work; the tubes need to be designed for HO applications. T8HO tubes in the correct length exist, but I couldn't find them in stock or in packs fewer than 18. LED tubes for this application don't exist as far as I could tell. But, the T12HO tubes I posted previously were readily available.
I ordered the T12HO tubes and reinstalled the original ballast. The tubes arrived today and everything worked just as it should (including a humming ballast. I may replace it with electronic T12 ballasts in the future).
I've already started painting a few of the panels using Rustoleum matte black paint and they look great. Once I get those finished, reassembly and hanging are the last steps. 47427
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.