View Full Version : General Dash Removal..
Lwanmtr
11-05-2016, 06:12 PM
Ok I looked around and couldnt find a writeup on this (aside from binnacle removal)...
Is there a good step by step on removing the whole dash? I figured while my interior is gutted, I might as well pull that to see if I can make it not look so bad and see if I need new speakers (hooray to the genius that didnt make those more accesible).
Thanks
Rich_NYS
11-05-2016, 06:52 PM
Kings1527 has a good write-up here: http://delorean6575revisited.blogspot.com/2013/04/stripping-interior-and-removing-dash.html?view=sidebar but his pics are no longer available on the site. Might be worth a shot to PM him & ask if he has the accompanying pics available.
I recall when I took mine out it, a flex-head 10mm wrench was very useful (advice from Alex as well.)
I'll look to see if I have any pics...
Lwanmtr
11-05-2016, 11:35 PM
Thanks, I'll look at that
Henrik
11-08-2016, 02:32 PM
Ok I looked around and couldnt find a writeup on this (aside from binnacle removal)...
Is there a good step by step on removing the whole dash? I figured while my interior is gutted, I might as well pull that to see if I can make it not look so bad and see if I need new speakers (hooray to the genius that didnt make those more accesible).
Thanks
Rob - you don't need to pull the dash to get to the front speakers. Yes, they're a pain to access but it is possible with extensions. I do recommend that you remove the seats though (hopefully you have not re-installed them yet since you installed the sound insulation) because you will need the space to lay on your back.
dn010
11-08-2016, 02:57 PM
Ok I looked around and couldnt find a writeup on this (aside from binnacle removal)...
Is there a good step by step on removing the whole dash? I figured while my interior is gutted, I might as well pull that to see if I can make it not look so bad and see if I need new speakers (hooray to the genius that didnt make those more accesible).
Thanks
If your dash is looking rough, it is possible to cover it with upholstery and reinstall it, as I did. However, If you've never done upholstery before, this is very difficult - getting the ripples out and seams flat is tough, then once you have it complete the challenge is installing it without tearing it up from the A post trim. I still haven't done anything with my speaker holes yet, maybe next month...
http://dmctalk.org/attachment.php?attachmentid=42039&d=1463597815
Lwanmtr
11-08-2016, 04:45 PM
Yeah, I know you can get the speakers out without pulling the dash...but my dash is really badly baked, so I figured a good idea to get it out while the car is still empty (havent put my seats or carpet back in yet).
Not sure which route I'll go on recovering or replacing it.
David T
11-08-2016, 05:34 PM
Yeah, I know you can get the speakers out without pulling the dash...but my dash is really badly baked, so I figured a good idea to get it out while the car is still empty (havent put my seats or carpet back in yet).
Not sure which route I'll go on recovering or replacing it.
You might also consider repairing it and painting it. Recovering is not easy since it fits tightly into other pieces. Fortunately DMCH does sell a remaned part but there have been some have complaints about fit.
Lwanmtr
11-08-2016, 07:38 PM
Here's a pic of the dash, the dash pad isnt quite as bad as I remembered (have had one of those covers on it to hide it..hehe), but it is all dark n icky..of course the binnacle is knackered..and my a-pillars are warped n icky..hehe.
47236
I could prolly deal with the one crack in the dash, if someone has a good way to clean up all the age n stuff off it.
Oh..and in case youre wondering, the green tape on the steering wheel is there to tell me about where center is..I dont have a wheel puller to get it off and fix it, and put the new indicator assembly on.
john 05141
11-09-2016, 08:28 AM
I resprayed my dashboard while installed, but that is not an issue here.
Removing the dashboard is not easy. The middle bolts are very hard to reach, that is why I decided to paint in the car
Mask everything, take a deep breath and.....
Jan
dn010
11-09-2016, 10:26 AM
I tried the paint route, it lasted for many years before it pealed off and looked bad again. Not only that, the filled and repaired cracks were still pretty obvious under the paint. After getting a lot of mixed reviews of the new dashboards DMCH sells, I decided recovering it was my best option and it was already out due to an evaporator replacement (again). This project cost me about $50 in upholstery compared to $300.
If you don't want to deal with removal then spraying the dash in place like already stated is probably your best bet. You'll risk damaging the dash further trying to remove it if you don't know what you're doing - you can also damage the A post trim if you don't know what you're doing. Either way - once you're done repairing it, it makes a world of difference!
Drive Stainless
11-09-2016, 12:13 PM
I had a DMCH dashboard and it really wasn't terrible.
In my experience, and I have an earlier car, the fitment is comparable with the OEM dashboard except in the glovebox area. To get the glovebox lid to sit flush, I had to make a bracket to mount the hinges lower. The other thing is that it has been shown to break down if the car is stored outdoors. I had mine installed for 6 years, stored in a garage when not in use, and it held up just fine.
DaraSue
11-09-2016, 04:10 PM
I used this guide to remove the binnacle just now: http://www.dmcnews.com/Techsection/dashboard.html
It has a section after that about taking the dash apart. I didn't do that part but the binnacle section was helpful so the dash section looks like it would work, too.
Dennis added in my other thread that you can pull the speedo cable by pressing on the tab where it plugs into the back of the cluster. When I was doing mine I found that I couldn't pull the binnacle very far out without disconnecting the cable first so if it's hard to reach behind the binnacle then maybe you want to do like the guide says and disconnect it at the other end.
Lwanmtr
11-09-2016, 04:52 PM
Im not too worried about damaging the A-pillars...they're warped n nasty too. Not sure if you can see the far one in the pic..but they're both the same and will need to be replaced.
Its too bad about DMCH's replacement...Heard more negatives than positives about them. Be nice if someone produced a good quality replacement.
Christian Dietrich
11-10-2016, 08:28 AM
http://uploads.tapatalk-cdn.com/20161110/1457933ff579d4bb5a8b41556a24af5b.jpghttp://uploads.tapatalk-cdn.com/20161110/bc9dce3c33932532275c60db321d816b.jpghttp://uploads.tapatalk-cdn.com/20161110/85a5996d08ec20320e84a3dd4cfa7196.jpghttp://uploads.tapatalk-cdn.com/20161110/e54f1b4dead5e0610f459a5bfb936f39.jpghttp://uploads.tapatalk-cdn.com/20161110/27726c4901ae8fb09bbcb2891c1b7e68.jpghttp://uploads.tapatalk-cdn.com/20161110/c27ec24633c4ed073d2d8b95270bf353.jpghttp://uploads.tapatalk-cdn.com/20161110/099fdff28799352ee4618db186bbb9aa.jpg
Here is my before and after. When i found mine in 2004, it had sat abandoned since the early 1990's. Inside was baked bad. So i gutted it and redid it with a slight update. I like the DMCH dash but i would add insulation or dynomat under to keep it from rubbing the fiberglass chassis and squeeking. Other than that the fit and finish i found to be pretty good. Only the carpet is original. Everything was completely redone. The interior is not really difficult to do. Alot of 10mm in the dash.
Sent from my SM-N920P using Tapatalk
Christian Dietrich
11-10-2016, 08:34 AM
Btw, when i had it out i redid alot of tge wiring, radio update with sub and ran wires for heated seats and custom led and Electroluminescence lighting.
Sent from my SM-N920P using Tapatalk
Lwanmtr
04-28-2017, 09:45 PM
Does anyone have a chart showing the locations of all the nuts holding the dash pad on?
DMC5180
04-29-2017, 09:00 PM
Does anyone have a chart showing the locations of all the nuts holding the dash pad on?
LH
https://uploads.tapatalk-cdn.com/20170429/65076fbf9a22ce898c6ab6173aef12f0.jpg
Center
https://uploads.tapatalk-cdn.com/20170429/20bba38262fa7aad9239690d096c944f.jpg
RH
https://uploads.tapatalk-cdn.com/20170429/7973c1f3d0fd61e368c2c889d42d35cb.jpg
Tips
To get at the center location, remove glove box insert and RH kneepad. A ratcheting box end wrench is handy to have for these two.
Remove Center console to avoid damaging it when lifting the dash out.
You may need to remove the defroster grills Too.
The 2 corners are fairly easy to access, just stick your hand up under those areas and you will be able to feel the nuts on the underside of those circled locations.
Sent from my iPhone using Tapatalk
Lwanmtr
04-30-2017, 03:56 AM
Here's a simple image showing the locations in case other folks need to know where they are....
51216
They're pretty easy to get to except the 2 in the center..kinda gotta get up over the vents.
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.