View Full Version : Transmission Auto Auto Trans Major Leak
DMC5738KC
11-07-2016, 03:18 PM
Looking for advice from the forum - my auto transmission, which had been working fine, except for a minor leaks here and there finally blew out a large quantity of fluid from the bell housing area. Not good. I have begun the process of pulling the engine and transmission to determine what the problem is - assuming it's a blown out seal on the input shaft, but I really don't know.
The car had sat for the last 20 years and I changed the fluid, filter, and shift computer before driving it for short distances over the last year. No burnt smelling oil and no slipping prior to this - just a small leak waiting to get bigger.
The engine has a fair amount of oil covering it too, so I want to clean it all up and replace whatever gaskets/seals at the same time.
The question is.....should the transmission get a full rebuild, or can I get away with the seals/gaskets that are needed?
Also, while I'm in there - other than the TABS, bushings, engine mounts, transmission mount, rear main seal, what should be done? Engine was running well and doesn't appear to need rebuilding, but while it's out.....
What vendors have the best parts for the obvious replacement parts?
Many Thanks,
Mike
Sent from my SM-G930T using Tapatalk
Jonathan
11-07-2016, 03:30 PM
The question is.....should the transmission get a full rebuild, or can I get away with the seals/gaskets that are needed?
I have no experience with that kind of failure, so I won't pretend to know what to suggest.
Also, while I'm in there - other than the TABS, bushings, engine mounts, transmission mount, rear main seal, what should be done? Engine was running well and doesn't appear to need rebuilding, but while it's out.....
Your other question though...
- fuel accumulator will be more accessible with the car up in the air and the drive train out of the way. It's not the same access hole, but if your accumulator is original still, replace it.
- put a new fuel filter in while you're at it.
- your exhaust is all going to come out to do the work you mentioned, so you could put in new exhaust manifold gaskets if you'd like.
- new O2 sensor as well.
- replace muffler brackets if any are missing or broken.
- fix any peeling epoxy on the frame in and around the engine cradle while things are apart.
- same too if the bottom edge of the rear fascia has any of those bolts rusted away and not holding the bumper to the edging strip behind the muffler.
- replace the heatshields if yours are beat up and if you can get replacements (the one for the catalytic converter is a little hard to come by).
DMC5738KC
11-07-2016, 03:40 PM
I have no experience with that kind of failure, so I won't pretend to know what to suggest.
Your other question though...
- fuel accumulator will be more accessible with the car up in the air and the drive train out of the way. It's not the same access hole, but if your accumulator is original still, replace it.
- put a new fuel filter in while you're at it.
- your exhaust is all going to come out to do the work you mentioned, so you could put in new exhaust manifold gaskets if you'd like.
- new O2 sensor as well.
- replace muffler brackets if any are missing or broken.
- fix any peeling epoxy on the frame in and around the engine cradle while things are apart.
- same too if the bottom edge of the rear fascia has any of those bolts rusted away and not holding the bumper to the edging strip behind the muffler.
- replace the heatshields if yours are beat up and if you can get replacements (the one for the catalytic converter is a little hard to come by).
Thanks for the input. I've done the accumulator, fuel filter, replaced the exhaust with stainless headers and mufflers, fairly new O2 sensor. I've already done a ton of work on this car over the last year, so this an unfortunate situation, but I'll definitely take the opportunity to clean up frame rust and whatever else is found. Thought I was getting close to being done....are you ever done with a DeLorean???
Sent from my SM-G930T using Tapatalk
David T
11-07-2016, 04:39 PM
Thanks for the input. I've done the accumulator, fuel filter, replaced the exhaust with stainless headers and mufflers, fairly new O2 sensor. I've already done a ton of work on this car over the last year, so this an unfortunate situation, but I'll definitely take the opportunity to clean up frame rust and whatever else is found. Thought I was getting close to being done....are you ever done with a DeLorean???
Sent from my SM-G930T using Tapatalk
You really don't need to remove the motor to get the transmission out. Sounds like the converter seal. The "while you are in there" stuff would be to pull the pan and clean or replace the filter, the pan gasket and the output seals. All of this stuff can be done without pulling the transmission. Also change the oil in the final drive and the transmission. When putting the transmission back check all of the external adjustments. The convertor seal doesn't fail that often so you must figure out why it failed. You may have to replace the convertor and the bushing.
DMC5738KC
11-07-2016, 04:52 PM
You really don't need to remove the motor to get the transmission out. Sounds like the converter seal. The "while you are in there" stuff would be to pull the pan and clean or replace the filter, the pan gasket and the output seals. All of this stuff can be done without pulling the transmission. Also change the oil in the final drive and the transmission. When putting the transmission back check all of the external adjustments. The convertor seal doesn't fail that often so you must figure out why it failed. You may have to replace the convertor and the bushing.
Thanks David - it's a situation where there has been a lot of leaking going on for some time from the engine (it's coated with grit and grime) and there is frame rust too on the upper part of the shock towers (whatever you call them), so it's there's really 3 reasons for pulling the engine and transmission at the same time. Considering how long it's been leaking from the bell housing area I'm expecting to see the input shaft pitted and a seal failure.....we shall see. Thanks for your advice! Definitely will clean everything up while I'm on there.
Sent from my SM-G930T using Tapatalk
David T
11-07-2016, 08:04 PM
Thanks David - it's a situation where there has been a lot of leaking going on for some time from the engine (it's coated with grit and grime) and there is frame rust too on the upper part of the shock towers (whatever you call them), so it's there's really 3 reasons for pulling the engine and transmission at the same time. Considering how long it's been leaking from the bell housing area I'm expecting to see the input shaft pitted and a seal failure.....we shall see. Thanks for your advice! Definitely will clean everything up while I'm on there.
Sent from my SM-G930T using Tapatalk
That area is known as the "engine cradle" and typically rusts around the bottom. Dirt and grease is easily pressure washed and most areas can be reached for repair without removing the motor unless it is really bad. If the rear is bad the front is usually even worse. Often it is so bad it becomes worth considering reframing the car. Leaking doesn't damage parts, it just makes a big mess. If the epoxy coating is intact the frame cleans up well. In fact, the leaked oil will actually keep things from rusting, preserving the frame.
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.