View Full Version : Fuel Car Runs Like Crap...
81dmc
11-09-2016, 10:14 PM
Well, I finally got around to starting my car for the first time in 4 months, and of course there are issues with k-jet...
First of all, when initially started, the engine stutters and shakes badly, and if I try to give throttle, it just dies. However, if I slightly push the mixture plate down, the car runs beautifully.
So, I hooked up my dwell meter:
1. When running hot, the engine gives a dwell reading of 55-65 degrees.
2. When I push the plate down very slightly, the engine gives an in-spec reading of 35-45 degrees.
Does this point to a mixture issue? If so, do I just use a 3mm allen and make very small (<1/6 turn) increments? Also, it seems the frequency valve is always buzzing, which I'm assuming is normal.
Thanks
David T
11-09-2016, 10:27 PM
How old is the fuel? If it doesn't smell fresh dump it and get some fresh fuel into it. If it runs better when you push down on the air sensor plate it is probably running lean. Either your mixture is way off, you have air leaks, or bad/dirty injectors. Messing with the mixture screw is the LAST thing you do. If the car ran well before (and no one touched the screw) you should NOT try to "fix" it by adjusting the mixture screw.
81dmc
11-09-2016, 10:42 PM
How old is the fuel? If it doesn't smell fresh dump it and get some fresh fuel into it. If it runs better when you push down on the air sensor plate it is probably running lean. Either your mixture is way off, you have air leaks, or bad/dirty injectors. Messing with the mixture screw is the LAST thing you do. If the car ran well before (and no one touched the screw) you should NOT try to "fix" it by adjusting the mixture screw.
The fuel is fairly new and smells fine.
I replaced all my injectors 2 years ago, and they still looked great when I pulled them to change the seals.
Also, I doubt they are dirty since I haven't opened the fuel lines in over a year.
However, In the last few months, I only replaced my 35 year old injector seals and upgraded my frequency valve lines.
opethmike
11-10-2016, 12:31 AM
Put a fuel pressure gauge on there; you are shooting in the dark without that information. I would start with checking for proper operation of the warm up regulator.
sdg3205
11-10-2016, 02:04 AM
Well, I finally got around to starting my car for the first time in 4 months, and of course there are issues with k-jet...
First of all, when initially started, the engine stutters and shakes badly, and if I try to give throttle, it just dies. However, if I slightly push the mixture plate down, the car runs beautifully.
So, I hooked up my dwell meter:
1. When running hot, the engine gives a dwell reading of 55-65 degrees.
2. When I push the plate down very slightly, the engine gives an in-spec reading of 35-45 degrees.
Does this point to a mixture issue? If so, do I just use a 3mm allen and make very small (<1/6 turn) increments? Also, it seems the frequency valve is always buzzing, which I'm assuming is normal.
Thanks
Wait, was it running just fine 4 months ago, and NOW runs like crap? As in, nothing has changed but the passage of time?
81dmc
11-10-2016, 10:16 AM
Wait, was it running just fine 4 months ago, and NOW runs like crap? As in, nothing has changed but the passage of time?
Now it hesitates, misfires, and stalls. However, 4 months ago, I only had an issue where the engine would stall after a sudden acceleration.
EDIT: I just bought a CIS pressure test kit on Amazon. The CPR is one of the only components that I have not either cleaned or replaced.
mluder
11-10-2016, 05:25 PM
I assume you checked obvious stuff like spark leads properly seated and especially injectors... I had a backfire once blow an injector out of its seat and the engine ran like crap for obvious reasons until the fuel smell tipped me off.
Steve
81dmc
11-10-2016, 05:52 PM
I assume you checked obvious stuff like spark leads properly seated and especially injectors... I had a backfire once blow an injector out of its seat and the engine ran like crap for obvious reasons until the fuel smell tipped me off.
Steve
Yep, checked all the obvious things.
This is the pressure tester I bought. I will receive it tomorrow.
https://www.amazon.com/gp/aw/d/B008FJXA3M/ref=ya_aw_od_pi?ie=UTF8&psc=1
81dmc
11-10-2016, 07:51 PM
Today I ran the engine trying to figure out my issue, and I believe my CPR is the culprit.
When the engine was cold, any movement of the throttle would bog the engine down until a stall. By time the engine was warm however, It mostly ran fine but with a dwell of 55-65 and a loudly clicking vacuum solenoid.
With that said, what is the best way to go about cleaning the CPR?
bytes311
11-10-2016, 08:21 PM
My car exhibits similar characteristics when cold. The heating element inside the warm-up regulator toasted, so I just let my car warm up a bit (5 min or so) before I drive it. Does your frequency valve buzz?
81dmc
11-10-2016, 09:15 PM
My car exhibits similar characteristics when cold. The heating element inside the warm-up regulator toasted, so I just let my car warm up a bit (5 min or so) before I drive it. Does your frequency valve buzz?
It buzzes constantly. I also checked the resistance of the heater, and it is fine.
But I'm impatient, so I decided to take out the CPR.47257
bytes311
11-10-2016, 09:34 PM
I think the only part that you can clean yourself is the inlet screen, ie blow it through with compressed air. A vendor may be able to rebuild or re-calibrate them.
81dmc
11-10-2016, 09:38 PM
I guess I'll put it back together cleaned, and if problems persist, I'll bring it to DMCH for an exchange.
81dmc
11-10-2016, 10:22 PM
Update: The car is running a hell of a lot better now, with only only a slight sputter on acceleration. The dwell also fluctuates correctly now. When I get my pressure gauge, I will correct the main pressure.
Thanks for all the advice, especially to The Guru. I would have been screwing with mixture, when it was actually a dirty CPR/WUR screen.:8ball:
Here's what the 14mm banjo bolt looked like.47258
opethmike
11-10-2016, 11:52 PM
I'd consider replacing that; looks like bits of metal are flaking off.
81dmc
11-11-2016, 12:01 AM
I'd consider replacing that; looks like bits of metal are flaking off.
It's a new stainless banjo from DPI, so I don't think it's bad. The particles actually looked like some random dirt that got lodged in the distributer over year ago. I guess after a long sit, it finally accumulated at the CPR inlet.
David T
11-11-2016, 12:10 AM
Update: The car is running a hell of a lot better now, with only only a slight sputter on acceleration. The dwell also fluctuates correctly now. When I get my pressure gauge, I will correct the main pressure.
Thanks for all the advice, especially to The Guru. I would have been screwing with mixture, when it was actually a dirty CPR/WUR screen.:8ball:
Here's what the 14mm banjo bolt looked like.47258
If you mentioned from the beginning that it runs like crap when cold but OK once it warmed up I would have told you to check the CPR right away. As for "correcting" the main (primary) pressure, if it is running OK now, why would you touch that? Hook up the pressure gauge and monitor the control pressure as the motor warms up. Refer to D:02:01 #2 fig 17 for the control pressure/temperature chart. Sometimes you can make it work by cleaning that screen and you can fix the burnt up wires inside. If that doesn't make it work right the best thing to do is exchange it for a rebuilt unit. Make sure the vent hose is on as per ST-18-10/81 and all of the vacuum lines are not cracked, split, leaking, or disconnected. Other things to check are ST-32-12/81 and verify the delay valve is correctly oriented. The CPR must be firmly attached to correctly sense engine temperature.
81dmc
11-11-2016, 12:20 AM
If you mentioned from the beginning that it runs like crap when cold but OK once it warmed up I would have told you to check the CPR right away. As for "correcting" the main (primary) pressure, if it is running OK now, why would you touch that? Hook up the pressure gauge and monitor the control pressure as the motor warms up. Refer to D:02:01 #2 fig 17 for the control pressure/temperature chart. Sometimes you can make it work by cleaning that screen and you can fix the burnt up wires inside. If that doesn't make it work right the best thing to do is exchange it for a rebuilt unit. Make sure the vent hose is on as per ST-18-10/81 and all of the vacuum lines are not cracked, split, leaking, or disconnected. Other things to check are ST-32-12/81 and verify the delay valve is correctly oriented. The CPR must be firmly attached to correctly sense engine temperature.
It was not running optimally both when cold AND when hot...
Also, as I was further testing it, some sputter was still present, but it is has definitely improved since my first post. In all, I will just check everything once I get my pressure tester. If the pressure does not fall within specs, I will exchange the CPR at DMCH on Monday.
David T
11-11-2016, 11:24 AM
If it still doesn't run well when hot after replacing the CPR you have other problems like bad injectors, vacuum leaks, etc. That would mean it wasn't running all that well BEFORE the CPR went bad.
81dmc
11-13-2016, 08:33 PM
The problem is now fixed.
All three plugs on the passenger side were fouled, so I cleaned them with carb cleaner. Also, I replaced the ignition ECU with a gm 4 pin module since I run no ballast with my 0012 Bosch blue coil. The car then ran great... for about 10 minutes. After that mark, idle jumped to 2000rpm, and after various tests with some wiring and vacuum hoses, I think I have traced it down to Dave M's Idle ECU. I have already PMed him and am waiting on a reply.
Edit: I will be sending it to Dave for testing.
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.