Log in

View Full Version : Frame & Body Broken Passenger Side Mirror



lazabby
11-11-2016, 07:35 PM
While pushing the car into the garage, the person steering got too close to the garage door jamb and broke the mirror even though it was folded in. Now, instead of swiveling it hangs loosely. Is it possible to fix it or do I have to buy a new mirror assembly? If it has to be replaced, are ther instructions posed on the web somewhere?

Lwanmtr
11-11-2016, 08:57 PM
Depends how bad the damage is...I'd think replace cause the one I had didnt look like it could be repaired.

Swapping them is pretty easy, though a lil fiddly..pretty much remove the upper door card, peel back the plastic thingy (if you have one) , then there are 3 nuts that hold it on...just have to make sure you dont drop them into the door when you take them off.

David T
11-11-2016, 09:22 PM
Take the old one off. You have to do that in any case. Take it apart and see if you can repair it. If you can't then order another one. If you don't mind getting a used one there are vendors that have them and they will be a little cheaper. Don't feel bad. I have heard of several stories of where the owner backed the car out of the garage to wash it and it would not start so they pushed it back in WITH THE DRIVER'S DOOR OPEN! Once that door gets tweaked by hitting the door jamb of the garage it is never the same and a whole lot more expensive to fix than a mirror.

DMCMW Dave
11-11-2016, 09:30 PM
While pushing the car into the garage, the person steering got too close to the garage door jamb and broke the mirror even though it was folded in. Now, instead of swiveling it hangs loosely. Is it possible to fix it or do I have to buy a new mirror assembly? If it has to be replaced, are ther instructions posed on the web somewhere?

You might be table to fix it. Underneath the pivot there is a small plastic cover that you can pry off. Then look at the retainer. If the clip simply popped off you can put it back together. If the clip snapped it gets a bit more complicated, but once you can see it you should understand what happened, and be able to post a photo if not.

Replacement is not too difficult, just remove the upper interior door panel, and the pillar trim that runs up the front of the door. Both are held on by fir tree clips. There are three screws that hold the mirror to the car. Simply unplug the wire and remove the mirror. You will need to do this anyway if you need to repair the retainer as the retainer that holds the pivot has the wiring going through the center of the clip.

The new mirror will come with the wiring attached but you will need to move the plastic connector shell from the old mirror to the new (that's how they are stocked).

lazabby
11-12-2016, 12:27 PM
You might be table to fix it. Underneath the pivot there is a small plastic cover that you can pry off. Then look at the retainer. If the clip simply popped off you can put it back together. If the clip snapped it gets a bit more complicated, but once you can see it you should understand what happened, and be able to post a photo if not.

Replacement is not too difficult, just remove the upper interior door panel, and the pillar trim that runs up the front of the door. Both are held on by fir tree clips. There are three screws that hold the mirror to the car. Simply unplug the wire and remove the mirror. You will need to do this anyway if you need to repair the retainer as the retainer that holds the pivot has the wiring going through the center of the clip.

The new mirror will come with the wiring attached but you will need to move the plastic connector shell from the old mirror to the new (that's how they are stocked).

It looks like I have a door panel removal in store for me either way. I'll take it off and go from there. Hopefully the clip simply fell off. Is the clip something that would have fallen inside the miiror or on the ground. I've never taken the mirror apart before.

mluder
11-12-2016, 04:39 PM
Don't feel bad. I have heard of several stories of where the owner backed the car out of the garage to wash it and it would not start so they pushed it back in WITH THE DRIVER'S DOOR OPEN! Once that door gets tweaked by hitting the door jamb of the garage it is never the same and a whole lot more expensive to fix than a mirror.

Ask me how I know about this... You must know my previous owner. LOL
That door is the bane of my existance.

Cheers
Steve

DMC5180
11-12-2016, 07:20 PM
It looks like I have a door panel removal in store for me either way. I'll take it off and go from there. Hopefully the clip simply fell off. Is the clip something that would have fallen inside the miiror or on the ground. I've never taken the mirror apart before.

For now, just pop the cover out. This is what it is supposed to look like.

http://uploads.tapatalk-cdn.com/20161112/7f605d47e06e8bb57e484053098b1e78.jpg

http://uploads.tapatalk-cdn.com/20161112/b72120947c8e73846cd24c80f58df2c6.jpg

http://uploads.tapatalk-cdn.com/20161112/8a92c235ab15aa370cbbbaf1e033e840.jpg

It's a push on one way retainer.


Sent from my iPhone using Tapatalk

lazabby
11-23-2016, 09:06 PM
I got the mirror off. Actually pretty easy. I popped off the bottom panel and see the retainer clip and three washers. I just need to re-assemble it loks like to me. Thanks for all the help.474794748047481

DMC5180
11-23-2016, 09:17 PM
Cool, that should be a Snap to fix!..........Ba-bump, tisch [emoji6]


Sent from my iPhone using Tapatalk

lazabby
11-23-2016, 10:06 PM
Well I started to push everything together and saw that the retainer ring/clip is broken. What's the next step? Where to find a new one and how do I get it on that cord? The only way I can see is to pull the wires out of the plug, pull the wire through to hole in the mirror body, replace the ring/clip and push the wires back through the mirror body hole and back into the plastic plug.

DMC5180
11-23-2016, 10:15 PM
Bummer. You have to de-pin the terminals from the connector housing. You might find a suitable size here:
http://www.clipsandfasteners.com/mobile/category.aspx?id=153&404;http://www.clipsandfasteners.com:80/Push_On_Retainers_s/153.htm=

What is the diameter of the OD of the tube/stem?

Sent from my iPhone using Tapatalk

BABIS
11-24-2016, 02:26 AM
I guess you can use a circlip

lazabby
11-26-2016, 11:23 AM
I'm not have luc kgetting a retainer nit/clip to fit. Ace Hardware has something very close. !/2" is too big and and the 7/16" might work but can't get it on. Besides, they are not exactly like the one in the car. I suspect these are metric. Anyone know what the exact side of these things are and where to find them? I don't see one on the link provided.

lazabby
11-26-2016, 11:25 AM
I guess you can use a circlip

I'm not sure a circlip could withstand the pressure when the mirror is rotated.

DMC5180
11-26-2016, 11:37 AM
I found the manufacturer over in the U.K. But it appears they only sell volume quantities and high minimum charge for US customers. You might see if you could get some engineering samples (free) or at minimal cost. Or see if they have a retail/wholesale seller in the US to get a small quantity.

https://www.springmasters.com/sp/starlock-push-on-fasteners-metric.html


Sent from my iPhone using Tapatalk

lazabby
11-26-2016, 04:19 PM
I found the manufacturer over in the U.K. But it appears they only sell volume quantities and high minimum charge for US customers. You might see if you could get some engineering samples (free) or at minimal cost. Or see if they have a retail/wholesale seller in the US to get a small quantity.

https://www.springmasters.com/sp/starlock-push-on-fasteners-metric.html

Thanks for finding that. I now know the technical name for them (starlock). I contacted the company. They're on Ebay too. I'm trying to see if there is local source in Houston.

DMC5180
11-26-2016, 06:28 PM
Looks like you can get a small quantity of any size, what ever it measures MM.
You select size and quantity.

https://www.ebay.com/itm/191781739493


Sent from my iPhone using Tapatalk

DMC5180
11-26-2016, 08:52 PM
I just tried to measure the Tube diameter imprecisely. It looks like 11 MM but then there is the smaller diameter groove. Which may indicate a 10MM starlock is the size you need. You probably need to remove the one you have and measure the dimensions and compare to the size chart on the first website page I posted.

The eBay site offers 10 and 12 MM sizes. You could get a few of each.


Sent from my iPhone using Tapatalk

PJ Grady Inc.
11-26-2016, 09:17 PM
We have a clip for this but your bigger problem is compressing all the "Belleville" type washers together enough to secure the clip. If you leave some out the install is easier but the mirror will vibrate. Getting enough leverage usually means removing the mirror glass and backing plate so you can get a tool onto the mirror pivot stem to apply the required pressure to secure the clip. Enjoy!
Rob

lazabby
11-28-2016, 01:17 PM
We have a clip for this but your bigger problem is compressing all the "Belleville" type washers together enough to secure the clip. If you leave some out the install is easier but the mirror will vibrate. Getting enough leverage usually means removing the mirror glass and backing plate so you can get a tool onto the mirror pivot stem to apply the required pressure to secure the clip. Enjoy!
Rob

I'd like to order to clip from you. How do you get the mirror off?

DMC5180
11-28-2016, 01:51 PM
Is the assembly removed from the door yet?

To remove the mirror(glass), you warm it up with a hairdryer. Then carefully work a narrow putty knife or butter knife in between the glass and plastic backer. Start at the inside lower corner. It helps to have the mirror adjusted so the corner is proud. Gently pry the glass and foam sticky tape away from the plastic backer. Once they are removed you should be able to see the fixing screws that hold the motor assembly into the housing via openings in the plastic mirror mount.


Sent from my iPhone using Tapatalk

PJ Grady Inc.
11-30-2016, 02:46 PM
Dennis beat me to it. Sounds about right. The last task is compressing the washers while installing the retainer clip.
Rob

PJ Grady Inc.
11-30-2016, 03:26 PM
I'd like to order to clip from you. How do you get the mirror off?

It's in the mail Shannon. Let us know how it works out.
Rob

DMC5180
11-30-2016, 03:56 PM
Dennis beat me to it. Sounds about right. The last task is compressing the washers while installing the retainer clip.
Rob


Rob,

Is the clip you supply the same as the original?


Sent from my iPhone using Tapatalk

dn010
11-30-2016, 04:11 PM
Pardon my intrusion here, but you say the motor can be accessed with the glass gone - can the motor be removed? My driver side must have a short, every time I press the adjust button the fuse blows. I can't seem to get it into the proper position even by pushing on the glass so I'd like to take it apart if possible...

DMC5180
11-30-2016, 04:31 PM
Pardon my intrusion here, but you say the motor can be accessed with the glass gone - can the motor be removed? My driver side must have a short, every time I press the adjust button the fuse blows. I can't seem to get it into the proper position even by pushing on the glass so I'd like to take it apart if possible...

Yes


Sent from my iPhone using Tapatalk

dn010
11-30-2016, 04:40 PM
Thank you.

DMC5180
11-30-2016, 05:29 PM
Thank you.

Well when say motor, its not removable in the traditional sense. It an actuator servo assembly. The actuator assembly is removable from the mirror housing. But it is not available as an individual part.


Sent from my iPhone using Tapatalk

dn010
11-30-2016, 05:34 PM
Damn, maybe I should have started a new thread on this. I guess I'll tear into it this weekend and see what I'm up against.

PJ Grady Inc.
11-30-2016, 05:46 PM
Yes


Sent from my iPhone using Tapatalk

Correct. But the motor needn't be removed to fix the pivot however as in Shannon's case.

PJ Grady Inc.
11-30-2016, 07:01 PM
Damn, maybe I should have started a new thread on this. I guess I'll tear into it this weekend and see what I'm up against.

The motor/actuator is actually two tiny electric motors linked by gears and linkage to a rotating plastic ball attached to the mirror support plate. A short in there would be problematic to fix but the good news is it's more likely to be the switch. I can fix bad switch's and have disassembled the actuator motor successfully. Try to verify the switch is good before going further. If you need a Act/Mtr I can help you there as well. I had a pic for you of the assembly torn apart but can't upload it for some reason.
Rob

JAZ_DMC
09-02-2019, 12:29 AM
For now, just pop the cover out. This is what it is supposed to look like.

http://uploads.tapatalk-cdn.com/20161112/7f605d47e06e8bb57e484053098b1e78.jpg

http://uploads.tapatalk-cdn.com/20161112/b72120947c8e73846cd24c80f58df2c6.jpg

http://uploads.tapatalk-cdn.com/20161112/8a92c235ab15aa370cbbbaf1e033e840.jpg

It's a push on one way retainer.

Digging up an old thread here. Are there any vendors that sell the access cover under the side mirrors? VIN 952 is missing this piece on the driver's side mirror (previous owner was not a detail person). The mirror is otherwise fine, so I hate to buy the entire thing.

Rhye
09-02-2019, 07:52 AM
Seems feasible to 3D-print it, even in cheapest FDM technology. I can prepare and post 3D model of the part, if anybody's interested.

Lwanmtr
09-02-2019, 04:46 PM
Be a cool idea to start a place where 3d print files could be stored when someone makes them...eventually we may have to make our own parts for everything..hehe.