Log in

View Full Version : Frame & Body Center console bracket height



1batt4u
11-16-2016, 10:39 PM
When I first removed the center console, the brackets on the console that connect onto body frame were bent. I thought they might have bent by accident after I noticed them like that, so I straightened them. After reinstalling console with brackets straight, console was sitting too high. There was a big gap between top of radio frame and console. So I tried to bend them the way they were.
Question is, can someone PLEASE measure the height, preferably in mm. Rear of console bracket I am getting under 30mm, up front by radio frame just above 30mm.

If someone can help me on this, I would really appreciate it!!

http://i68.tinypic.com/ji2qhc.jpg

http://i64.tinypic.com/1zvqqs0.jpg

Jonathan
11-17-2016, 08:32 AM
After reinstalling console with brackets straight, console was sitting too high. There was a big gap between top of radio frame and console.

Are you talking about there being a gap above the air vents under the top of the centre console? Like the uppermost edge of radio bracket/vents doesn't snug right up to the underside of the leather/vinyl console lip when you fit it all back together?

That could be your problem if there is one. It should wiggle in there and fit pretty snugly without any noticeable gap. It can be challenging to get it to drop down all the way to where it needs to go if you don't see or understand what it might be catching on preventing it from going down all the way. It could be the flaps along the sides that tuck in between the knee pads are getting caught on something. When you get it slipped in all the way you'll know it because it will be obvious.

1batt4u
11-17-2016, 04:34 PM
Are you talking about there being a gap above the air vents under the top of the centre console? Like the uppermost edge of radio bracket/vents doesn't snug right up to the underside of the leather/vinyl console lip when you fit it all back together?

That could be your problem if there is one. It should wiggle in there and fit pretty snugly without any noticeable gap. It can be challenging to get it to drop down all the way to where it needs to go if you don't see or understand what it might be catching on preventing it from going down all the way. It could be the flaps along the sides that tuck in between the knee pads are getting caught on something. When you get it slipped in all the way you'll know it because it will be obvious.

Yea, mine had a gap very top of frame and console lip, I could stick my fingers through. I bent those brackets back into shape to lower it.

A few times I was at PJ Grady's shop I noticed some center consoles laying around and the brackets were straight.

I was wondering is everyone else's brackets are bent like that or are they straight? Also, if someone can quickly measure the height of the bracket like I did in the picture. Curious to see how high it is supposed to sit.

Thank you!

bdmiko
11-17-2016, 06:50 PM
Have my console out of the car right now. Measuring in the same location as your ruler I get 1.15 inches or 29 mm.

David T
11-17-2016, 09:51 PM
Have my console out of the car right now. Measuring in the same location as your ruler I get 1.15 inches or 29 mm.

Those brackets are supposed to be straight and square. There should be washers under them too. You want them as high as you can get them but be careful not to pinch any wires or hoses. They get bent when someone climbs over the console or sits on it.

1batt4u
11-18-2016, 01:17 AM
Those brackets are supposed to be straight and square. There should be washers under them too. You want them as high as you can get them but be careful not to pinch any wires or hoses. They get bent when someone climbs over the console or sits on it.

Yea, but when they are straight the console sits high and there is a big gap over the radio frame.

1batt4u
11-18-2016, 07:51 PM
Does Josh sell the brackets in s/s?

1batt4u
11-20-2016, 12:39 AM
Bump!