Log in

View Full Version : General Oil cooler support bracket crossover with 110109 mounting bracket?



Jonathan
11-20-2016, 10:26 AM
My car has never had the oil cooler support bracket 108142 part.

https://store.delorean.com/p-6306-oil-cooler-supt-brkt.aspx

I would get a new one but they are NLA. I probably don't need to get it now considering it's been supported the way it is for 9+ years, but I like the idea of things being "complete" on my car, even when a bit unnecessary.

I saw this mounting bracket though online and wondered if the dimensions were close enough to make it work:

https://store.delorean.com/p-6332-mounting-bracket.aspx

It is also meant for coolant pipes, just in another location. I see that this one does not have a welded on threaded portion to secure to, but I think I can work around that.

What I was wondering was whether the dimensions, both the length from end to end and also the diameter of the clamping portion, would let me use it?

Anyone know?

Delorean Industries
11-20-2016, 10:47 AM
The smaller one is made for 1 1/4 pipe. The nla version is for 1 3/8. This will not work.

Jonathan
11-20-2016, 11:12 AM
The smaller one is made for 1 1/4 pipe. The nla version is for 1 3/8. This will not work.

Understood. Thanks for clarifying.

David T
11-20-2016, 01:16 PM
Understood. Thanks for clarifying.

it wouldn't take that much to make one.

Jonathan
11-20-2016, 07:00 PM
it wouldn't take that much to make one.

How so?

David T
11-20-2016, 10:01 PM
How so?

It is just a rectangular piece of sheet metal that is bent up and has a couple of holes in it with another small round piece screwed to it. For anyone who works with metal it isn't a particularly difficult part to make. When you have an old car and the parts are no longer available you have to get creative and sometimes make a part. Brackets are relatively simple to make.

DMC5180
11-20-2016, 11:08 PM
Check with Rob Grady, he has quite a selection of used parts on hand.

I'd also be curious what DMCH was using for all the Refurbished aka (new builds) they have done in the past. My understanding is that virtually all of them were built with automatics.

Sent from my iPhone using Tapatalk

Jonathan
11-21-2016, 09:13 AM
It is just a rectangular piece of sheet metal that is bent up and has a couple of holes in it with another small round piece screwed to it. For anyone who works with metal it isn't a particularly difficult part to make. When you have an old car and the parts are no longer available you have to get creative and sometimes make a part. Brackets are relatively simple to make.

This is what I had thought you were assuming. Not easy for all, just easy for someone that plays around getting creative making things out of metal.

Now, had you said making one out of Lego....


Check with Rob Grady, he has quite a selection of used parts on hand.

I'd also be curious what DMCH was using for all the Refurbished aka (new builds) they have done in the past. My understanding is that virtually all of them were built with automatics.

Sent from my iPhone using Tapatalk

If I'm not mistaken, this bracket is used on all cars, whether automatic or manual. In place of the oil cooler on the manual trans car is just a straight length of pipe.

https://store.delorean.com/p-6311-repl-oil-cooler-pipe.aspx

I was under the impression it still called for the support bracket though? I could be wrong... it's been known to happen.

DMC-81
11-21-2016, 09:33 AM
Hi Johathan,

Yes, my manual car has that bracket (108142).

dn010
11-21-2016, 10:04 AM
I was also missing this bracket on my car (also manual), I had one on my original frame but it was rusty and the stud holding it to the frame broke off long ago. James Wallen (Eagle-co94) sold me a good used one, you might send him a message asking if he has more. Otherwise, I'd call up Rob Grady.

DMC5180
11-21-2016, 11:45 AM
This is what I had thought you were assuming. Not easy for all, just easy for someone that plays around getting creative making things out of metal.

Now, had you said making one out of Lego....



If I'm not mistaken, this bracket is used on all cars, whether automatic or manual. In place of the oil cooler on the manual trans car is just a straight length of pipe.

https://store.delorean.com/p-6311-repl-oil-cooler-pipe.aspx

I was under the impression it still called for the support bracket though? I could be wrong... it's been known to happen.

The straight pipe is 1-1/4". The cooler tube is 1-3/8". The cooler requires transition (dual diameter) coupler hoses from 1-1/4 to 1-3/8 ID. The straight pipe (Manual) just requires the standard 1-1/4 hose connections.


Sent from my iPhone using Tapatalk

DMC5180
11-21-2016, 11:59 AM
I was also missing this bracket on my car (also manual), I had one on my original frame but it was rusty and the stud holding it to the frame broke off long ago. James Wallen (Eagle-co94) sold me a good used one, you might send him a message asking if he has more. Otherwise, I'd call up Rob Grady.

The bracket for the manual cars is still available NOS and I think DPI had some made in Stainless too.


Sent from my iPhone using Tapatalk

Jonathan
11-21-2016, 12:12 PM
The straight pipe is 1-1/4". The cooler tube is 1-3/8". The cooler requires transition (dual diameter) coupler hoses from 1-1/4 to 1-3/8 ID. The straight pipe (Manual) just requires the standard 1-1/4 hose connections.


Sent from my iPhone using Tapatalk


The bracket for the manual cars is still available NOS and I think DPI had some made in Stainless too.


Sent from my iPhone using Tapatalk

Thanks for the info, Dennis (and others).

Does the support bracket for the manual cars have a different part number? Or is the bigger one good for both applications (whereas a smaller one wouldn't quite be big enough for the larger diameter pipe)?

jwrayth
11-21-2016, 01:03 PM
The straight pipe is 1-1/4". The cooler tube is 1-3/8". The cooler requires transition (dual diameter) coupler hoses from 1-1/4 to 1-3/8 ID. The straight pipe (Manual) just requires the standard 1-1/4 hose connections.

I respectfully disagree, as when I switched to silicone hoses a few years ago now I had to get reducing sections to connect this pipe to the others as it was of a larger diameter and I have a manual transimission car. Specifically it was a 35mm to 32mm elbow at a 45 degree angle.

dn010
11-21-2016, 01:04 PM
The pipe in question on my MT is the same diameter as all the rest of the coolant pipes.


I respectfully disagree, as when I switched to silicone hoses a few years ago now I had to get reducing sections to connect this pipe to the others as it was of a larger diameter and I have a manual transimission car. Specifically it was a 35mm to 32mm elbow at a 45 degree angle.

DMC5180
11-21-2016, 01:33 PM
Jwrath,

You may be right, I just went looking in the parts schematics, it would appear the manual part is referred to as Replacement oil cooler pipe for manual transmissions. There are no other unique parts to be used for its installation. There is only one support clamp called out for that location, which would imply the pipe diameters are the same 1-3/8. The other 1-1/4 clamp bracket is used on the RH rear pipe ( later style) just under the coolant reservoir.


Sent from my iPhone using Tapatalk

DMC5180
11-21-2016, 03:23 PM
Thanks for the info, Dennis (and others).

Does the support bracket for the manual cars have a different part number? Or is the bigger one good for both applications (whereas a smaller one wouldn't quite be big enough for the larger diameter pipe)?

It appears that there is only one part number for that clamp bracket. I just did a visual check on my manual car. It does have the same clamp as the one shown as NLA. It is the bigger clamp configuration.


Sent from my iPhone using Tapatalk