PDA

View Full Version : Brake Okay SERIOUSLY, what the hell is wrong with my brakes?



ccurzio
11-23-2016, 05:36 PM
A while back I posted a thread (http://dmctalk.org/showthread.php?13265-What-the-hell-is-wrong-with-my-car), and in that thread I describe a problem:


I had a brake problem a while back (some of you probably remember this), and a lot of the symptoms of that problem stemmed from braking extremely hard. Thanks to Sean coming over and helping me replace the brake master cylinder, everything seemed to be working again. Unfortunately last week I was driving the car and had to brake hard, and the exact same symptoms have resurfaced - after hard braking the brake pedal becomes easier and easier to push, eventually going to the floor with ease, and only pumping the brakes to build pressure can make it easy to stop the car. No brake fluid leaks that I can see.

I just had the brake master cylinder replaced again yesterday, and apparently it was a giant waste of money because I'm still having the exact same problem.

HELP PLEASE. This is seriously pissing me off.

dn010
11-23-2016, 05:40 PM
Sounds like possibly air is entering or trapped in your system? Did you get a nice fluid stream on each caliper when bleeding?

ccurzio
11-23-2016, 05:43 PM
Sounds like possibly air is entering or trapped in your system? Did you get a nice fluid stream on each caliper when bleeding?

Had a professional brake shop perform the service.

sdg3205
11-23-2016, 06:21 PM
Do you have the factory soft lines? If they're forced to expand, the could take some time to constrict again. It's known they do deteriorate with age, either swelling or becoming glorified check valves.

Also - our callipers are notoriously hard to bleed. I'd be surprised if a non-dmc facility did it correctly. Still.... air, no matter where it is, would not (in my experience) cause a soft pedal only under certain circumstances. It would always be soft.

ccurzio
11-23-2016, 06:35 PM
Do you have the factory soft lines?

Honestly I have no idea. Easy way to check?

dn010
11-23-2016, 06:38 PM
Yes. Look at the lines coming off the frame and going to the caliper. If they are dark with a black plastic spiral, they're factory.


Sent from my iPhone using Tapatalk

sdg3205
11-23-2016, 06:39 PM
Honestly I have no idea. Easy way to check?

You bet. Here's factory (https://store.delorean.com/p-7499-hose-rear-brakes.aspx)

If they don't ring a bell, you're probably still running factory. New braided lines are visually quite different, in an array of colours (mine are red) and just have a coloured sheath over the braided hose.

ccurzio
11-23-2016, 06:47 PM
Yep. Looks factory to me.

http://i.imgur.com/5FFtnoh.jpg

And all bone dry, no less.

sdg3205
11-23-2016, 06:49 PM
I would call your preferred vendor and get their opinion before throwing any more money at it, but worst case scenario, new soft lines are a good investment in your own safety.

ccurzio
11-23-2016, 06:51 PM
Thanks Dave.

If anyone else has any other thoughts I'd love to entertain more suggestions, but so far what we have is plausible. Also, if any vendors would like to chime in as well, I'm all ears.

Some guy
11-23-2016, 08:41 PM
I dont know how likely this is. But 2 things come to mind.

I had a similar issue with my clutch petal. It ended up being the linkage was worn out and i wasn't getting the full push of the petal.

The other is that the o rings in the calipers are worn out. Are they leaking at all? I have read they weir out over time.

Jonathan
11-23-2016, 09:07 PM
I dont know how likely this is. But 2 things come to mind.

I had a similar issue with my clutch petal. It ended up being the linkage was worn out and i wasn't getting the full push of the petal.

The other is that the o rings in the calipers are worn out. Are they leaking at all? I have read they weir out over time.

This is exactly what I was thinking and had just fired up the computer to see if I could grab a photo or two to see if it was possible. I got beat to the punch by some guy though ;)

If it isn't fluid related with an air problem in the lines or calipers and no issues with the master cylinder, then I'd think it could be mechanical and you're some how getting short changed on how far you think the brake pedal is pushing and it isn't translating to the rod going into the master cylinder seeing the same length of push.

Here's an older picture of my car and the brake pedal linkage area. My car is tucked away sleeping for the winter or I'd get you a better one. It isn't zoomed in on that portion specifically but might still be useful for comparison.

47482

Ratrace427
11-23-2016, 10:42 PM
Brake systems are a just pistons and cylinders for hydraulics. A pedal will only get soft when air enters the system. Air can only enter when there is a leak. Systems leak around the pistons. Brake fluid absorbs moisture to prevent corrosion of the cylinders and pistons but over many years the fluid becomes saturated with water and then particles of rust. Once the fluid gets to that point the corrosion destroys the parts. The leak wont necessarily drip past the rubber seal but you should be able to find a very dirty oily spot on one of the calipers. Knowing that the master has been changed then the only other part of the system that can be damaged is the calipers. I am assuming that the master was changed because of corrosion. If it was changed and the fluid not completely flushed then the wheel calipers corrosion couldn't be that far behind. In the past i have only changed the bad part but the other has always gave me trouble shortly after. My advise is to change the calipers in pairs with new lines as well. A good mechanic can find the bad caliper easy by bleeding each individually looking for the air. It could be any one of them but i bet they are all in bad shape. You can rebuild them without buying new if the cylinders are not to badly pitted.

Take your car to another mechanic! After changing the master cylinder the system had to be bled. The mechanic should have seen the dirty caliper and let you know there was a problem. A good mechanic would have also diagnosed the issue before charging time to do a master cylinder change without it needing it. =(

David T
11-23-2016, 11:13 PM
Sounds like the next thing to replace would be the brake hoses.

Ratrace427
11-23-2016, 11:47 PM
Sounds like the next thing to replace would be the brake hoses.

hoses collapse internally making the brake hang and get hot. Think of a collapsed brake line as a check valve only letting fluid go in one direction.I have also had a line collapse and make the brake pedal hard to press. In a car with a brake booster you cant really tell that there is a harder than normal pedal. On the D there are some thin sheet metal anti squeak pieces under the pads. Those might be getting used up as well. just something else to put on the order sheet if you have noticed squeaky stopping.