PDA

View Full Version : Fuel Proofing my work after fuel distribution re-assembly?



rjd2
08-21-2017, 10:46 PM
Greetings-so I recently completed the replacement of a thermister. I did my best to tag my connections, and double check my work as I reassembled the intake/fuel distribution system, and thought I had it all right, but upon testing, I am not getting the engine to start. RIGHT at the first few cranks, it will sputter, sounding as though it is receiving a small amount of fuel, but it never takes, and after the first 2 seconds, the engine just cranks and doesn't start.

I read the entire fuel section of the manual(section D), and while I understand better the general "workflow" of the fuel system, it didn't give me much to proof my work. The few electrical connections(idle speed motor harness, etc) it details never got disconnected, or are obviously seated properly. I have a suspicion I missed a fuel hose or electrical harness somewhere. Is there a diagram anywhere that I could use to confirm I have all my fuel lines and electrical harnesses seated in the right position? (as an aside, I believe I have a fuel pressure gauge that fits this car, so should I throw that on between the CPR and the fuel distributor and see what i see?)

thanks for any advice!

Ron
08-21-2017, 11:00 PM
52898

David T
08-21-2017, 11:18 PM
See if a shot of Ether gets it to run at all. That will tell you if your problem is ignition or fuel.

rjd2
08-21-2017, 11:38 PM
Thanks Ron-I'll trace tomorrow and make sure it looks right.

Shot of ether-never done this before. can you elaborate?

Rich
08-22-2017, 12:55 AM
Thanks Ron-I'll trace tomorrow and make sure it looks right.

Shot of ether-never done this before. can you elaborate?

Ether is what's in starting fluid. Any auto parts store will have it.

LINK: Starting Fluid (http://www.autozone.com/deicer-and-starting-fluid/starting-fluid)

1 can is plenty. Follow the instructions on the can.

If an engine starts with starting fluid but not without it then there's a fuel delivery problem. If it won't start with starting fluid then look into the ignition system.

Ron
08-22-2017, 02:11 AM
Since it ran before this work and it sounds like it is getting spark (at least at first), I'd wild guess it is the CPR/WUR fuel line with the small banjo bolt that is supposed to go to the passenger side of the fuel distributor, but doesn't.

=====

I'd check that the air metering plate offers resistance when it is pushed down, after hearing the pump run. If it doesn't, it's fuel. If it does, press it all of the way down and release it immediately and then see if it acts the same when you try to start it.

NJP548
08-22-2017, 09:05 AM
I actually created a Fuel Host Diagram back in 2000 when the DML/DMCNews was the main source of DeLorean information on the Internet.

Please see my diagram below. Hopefully it helps.

52906

-Nick Pitello

rjd2
08-22-2017, 02:35 PM
thanks! it does help. i've proofed my fuel lines, and it appears to all be correct. there was one banjo bolt that i had to replace, as i lost one, but it was a direct order from DMC. the black and blue rubber hoses with no hose clamps on them, I'd like to verify proper seating and placement on those next, and then electrical.

Ron-is the air metering plate the plate that lies directly below the air cleaner? if so, then yes-it does provide a bit of resistance if i push it after attempting a start. if i attempt a 2nd start after depressing the metering plate, i don't get an initial "semi-fire" at all.


I actually created a Fuel Host Diagram back in 2000 when the DML/DMCNews was the main source of DeLorean information on the Internet.

Please see my diagram below. Hopefully it helps.

52906

-Nick Pitello

NJP548
08-22-2017, 03:01 PM
thanks! it does help. i've proofed my fuel lines, and it appears to all be correct. there was one banjo bolt that i had to replace, as i lost one, but it was a direct order from DMC. the black and blue rubber hoses with no hose clamps on them, I'd like to verify proper seating and placement on those next, and then electrical.

Ron-is the air metering plate the plate that lies directly below the air cleaner? if so, then yes-it does provide a bit of resistance if i push it after attempting a start. if i attempt a 2nd start after depressing the metering plate, i don't get an initial "semi-fire" at all.

Happy to hear it helped you! Good luck with the rest of your troubleshooting.

-Nick Pitello

rjd2
08-23-2017, 11:41 PM
Ok-made some progress. After reseating all of the electrical harnesses, the engine is now starting-however, it won't hold an idle at all. If I am not actively goosing the throttle, it stalls out immediately.

I am not sure if this is related or not, but the very first time the engine started, it stalled out, and then the battery connection went cold. It was strange. I checked all the fuses, none were blown, and I opened the cover to the battery to check voltage on a DVM, and the panel lights just came back on. I'm assuming it was a strange isolated event, but figured I'd mention, in case it helps diagnose the issue.

I believe the service manual said that after replacing the thermister, that the fuel distributor's mixture setting should be recalibrated; should I start there? I'm not sure where to start, since it won't hold an idle at all. Thanks everybody!!!

Jonathan
08-23-2017, 11:54 PM
Maybe you have an electrical connection problem with your ignition switch? That would cause a sudden and unexplainable loss of power.

Bitsyncmaster
08-24-2017, 05:56 AM
Ok-made some progress. After reseating all of the electrical harnesses, the engine is now starting-however, it won't hold an idle at all. If I am not actively goosing the throttle, it stalls out immediately.

I am not sure if this is related or not, but the very first time the engine started, it stalled out, and then the battery connection went cold. It was strange. I checked all the fuses, none were blown, and I opened the cover to the battery to check voltage on a DVM, and the panel lights just came back on. I'm assuming it was a strange isolated event, but figured I'd mention, in case it helps diagnose the issue.

I believe the service manual said that after replacing the thermister, that the fuel distributor's mixture setting should be recalibrated; should I start there? I'm not sure where to start, since it won't hold an idle at all. Thanks everybody!!!

You never know if the mixture was set to compensate for something you fixed. So yes anytime you do work on the engine, it's best to check the mixture but without it running, you can't check dwell. Make sure the "pipe of agony" is in the mixture unit sealed. Often the O-ring and the ring that holds it falls out which makes a massive vacuum leak which would make the engine not idle.

rjd2
08-24-2017, 07:48 AM
You never know if the mixture was set to compensate for something you fixed. So yes anytime you do work on the engine, it's best to check the mixture but without it running, you can't check dwell. Make sure the "pipe of agony" is in the mixture unit sealed. Often the O-ring and the ring that holds it falls out which makes a massive vacuum leak which would make the engine not idle.

thanks-is the "pipe of agony" the copper pipe that seats inside the bottom of the mixture unit, and is not fastened with any hose clamps or bolts or anything? It seemed kinda wonky to just slide it in, and then put the mixture unit in place when I reassembled...I'll check it. Thanks!

Bitsyncmaster
08-24-2017, 09:26 AM
thanks-is the "pipe of agony" the copper pipe that seats inside the bottom of the mixture unit, and is not fastened with any hose clamps or bolts or anything? It seemed kinda wonky to just slide it in, and then put the mixture unit in place when I reassembled...I'll check it. Thanks!

Yes. Normally you coat the part that slides in with grease and the O-ring makes the seal. To check it, shine a flashlight at it at night time, press the air plate down and look for any light in the mixture unit.

rjd2
08-24-2017, 02:52 PM
Yes. Normally you coat the part that slides in with grease and the O-ring makes the seal. To check it, shine a flashlight at it at night time, press the air plate down and look for any light in the mixture unit.got it. i have a hunch it is not providing a full vacuum; the play in it didn't feel "right" upon reassembly. do i need to pull the whole mixture unit to resecure it properly, or can i do it from the side? also, what kind of grease? i have hi-temp grease here; not much else, but i'll buy the right part for the job.

Bitsyncmaster
08-24-2017, 04:32 PM
got it. i have a hunch it is not providing a full vacuum; the play in it didn't feel "right" upon reassembly. do i need to pull the whole mixture unit to resecure it properly, or can i do it from the side? also, what kind of grease? i have hi-temp grease here; not much else, but i'll buy the right part for the job.

If it didn't feel right I bet the O-ring keeper fell out. It's a little ring that presses into the mixture unit. Sometimes it will be on the pipe so look if you can before you pull the pipe so it does not drop. I don't think you can get that ring back on without pulling the mixture unit out. So you want to be sure that's your problem.

What I did with mine was lock it into the mixture unit with a very thick loctite.

Any grease should work. The mixture unit only heats from radiant engine heat.

rjd2
08-24-2017, 09:49 PM
ok, so more info: i removed the copper pipe that vents into the mixture unit from the idle speed motor location. the copper "collar" that seats in the bottom left of the mixture unit was in place, with an o-ring seated inside it. in addition, i threw an extra o-ring on the pipe with a bit of hi-temp grease before repositioning it-it seems highly likely that i've got a good vacuum seal at that location. no change in behavior; it won't hold an idle. (the engine runs very rough at 1k RPM and under now; very choppy).

i have found that if the air cleaner is just propped on top of the mixture unit, the engine often won't start at all. i have to bolt the air cleaner down for it to consistently start. does this give credence to the idle issue being vacuum-related? i'll do some forum archive searching on cars not holding an idle, im sure it's common. thanks all!

Bitsyncmaster
08-25-2017, 07:00 AM
ok, so more info: i removed the copper pipe that vents into the mixture unit from the idle speed motor location. the copper "collar" that seats in the bottom left of the mixture unit was in place, with an o-ring seated inside it. in addition, i threw an extra o-ring on the pipe with a bit of hi-temp grease before repositioning it-it seems highly likely that i've got a good vacuum seal at that location. no change in behavior; it won't hold an idle. (the engine runs very rough at 1k RPM and under now; very choppy).

i have found that if the air cleaner is just propped on top of the mixture unit, the engine often won't start at all. i have to bolt the air cleaner down for it to consistently start. does this give credence to the idle issue being vacuum-related? i'll do some forum archive searching on cars not holding an idle, im sure it's common. thanks all!

Good it will idle. Now you can check the mixture via a dwell reading. Only thing I found with the air cleaner is if you have the adjustment mixture plug with the long wire "eye" you have to make sure your air cleaner clears that when you put it on.

rjd2
08-25-2017, 08:05 AM
Good it will idle. Now you can check the mixture via a dwell reading. Only thing I found with the air cleaner is if you have the adjustment mixture plug with the long wire "eye" you have to make sure your air cleaner clears that when you put it on.

sorry, maybe i didn't write clearly. it will NOT idle.... it will start, and run only if i hold the throttle at 2000RPM or up. it seems as if i tries to idle; if i let off the throttle, it will go down to about 250RPM, then surge upwards once, then die.

Bitsyncmaster
08-25-2017, 08:19 AM
sorry, maybe i didn't write clearly. it will NOT idle.... it will start, and run only if i hold the throttle at 2000RPM or up. it seems as if i tries to idle; if i let off the throttle, it will go down to about 250RPM, then surge upwards once, then die.

You could adjust the dwell if needed at 2000 RPM if it will keep running. Your other option is do the "base line" setting where you adjust the mixture to just before the injectors start to spray.

rjd2
08-25-2017, 07:41 PM
As always, thanks for your help (Bitsyncmaster, you are a resource unto yourself, thank you!!!)

I tried starting the car with the idle speed motor plugged, and unplugged-same behavior. it will run if i keep the RPMS above 1000; below 1000 and it stalls out immediately.

I also tried swinging the mixture 1/4 turn in each direction, just to see if it had any effect on behavior(I knew I needed to do a proper calibration anyway). Same behavior.

And even with the air cleaner bolted down, if I run the car for 3-4 minutes, after it stalls it will not start after that. At all. Hmmm.....

NckT
08-26-2017, 08:01 AM
Remove your idle motor and inspect it to see if the valve actually moves or if it is stuck in a position too far closed to give enough air flow to enable your car to idle

rjd2
08-26-2017, 02:16 PM
I inspected the idle speed motor; it appears to be working correctly. I took the hose off that connects to the brass pipe, facing the rear of the vehicle, and turned the key to the "run" position. The valve turned all the way to the right (right being towards the center of the engine). Then, it held that position for a bit and then slowly went back to the original position.

I checked all my hose connections for the solenoid valve, and the purge control valve; I believe I have it all correct(i initially had the two hoses to the solenoid valve swapped; after putting these in the proper position, it still didn't change the behavior).

Once the engine reaches a reasonable warmed-up temp, it refuses to start at all. I have to wait til it cools down completely for it to start at all. Is that any possible clue?

Ron
08-26-2017, 10:16 PM
Once the engine reaches a reasonable warmed-up temp, it refuses to start at all. I have to wait til it cools down completely for it to start at all. Is that any possible clue?Did you try a shot of ether after it refused to start while warm?

========
$.02

1. Do the test(s) Elvis suggested, and followups..., FIRST.
2. If it will still idle with the IAC valve disconnected (as reported in other thread), attach the pressure gauge and report findings...

rjd2
08-26-2017, 11:07 PM
Ron-not yet. I haven't been able to find it for sale...

rjd2
09-01-2017, 01:48 PM
Alright, more info. I installed a fuel pressure gauge between the CPR and the fuel distribution unit. See attached; that reading of ~44PSI seems to hold pretty steady. No leaks. This last time trying to start the engine with the fuel pressure gauge installed, i could not get it to stay running. it turned over, sputtered a bit, did that 3x times, and then it didn't start at all.

Any idea what this means? Does this rule out fuel pressure as a possible culprit? Thanks for the help.

rjd2
09-01-2017, 03:07 PM
53166

rjd2
09-01-2017, 06:14 PM
Sorry for the multiple posts; it is not clear to me how to edit previous posts, unfortunately. Please disregard the previous two posts about fuel pressure gauge behavior; it appears it is NOT working properly(i had the valve in the wrong position, whoops! :)

At the run position, the fuel pressure gauge stays at 30PSI. When I start the engine, it drops to about 15-20 PSI, and floats between those two numbers while I rev. Once it stalls out, it floats back up to 30PSI standing pressure. This seems low, no?

rjd2
09-01-2017, 07:17 PM
Here is a video of the fuel pressure gauge behavior:

https://vimeo.com/user70661996

Bitsyncmaster
09-01-2017, 07:36 PM
Try jumping the RPM relay so your not starting the engine. If your gauge has a shut off valve, you should get around 70 PSI with the valve shut. When the engine is cold you will get a low control pressure (valve open).

When the engine is started cold you run about 15 PSI and it quickly starts increasing and settles around 50 PSI on the hot engine.

When you shut the engine off you get rest pressure (same with the valve open or closed) which is normally about 42 PSI at first. My car it would take about 3 hours for that rest pressure to drop to zero.

rjd2
09-01-2017, 08:32 PM
Bitsyncmaster-thanks. My rest pressure with the FPG valve open is about 30. I can't get it anywhere near 50PSI running, but the engine won't idle, so i can't get it to run for too long. With the FPG valve closed, it jumps to about 44PSI.

It seems to me it's likely I have a vacuum issue, maybe? If so, where should I start investigating? Nothing changed at all upstream of the CPR, so I'd have to imagine the first place I should investigate is the mixture unit and fuel distribution unit?

Bitsyncmaster
09-01-2017, 08:40 PM
Bitsyncmaster-thanks. My rest pressure with the FPG valve open is about 30. I can't get it anywhere near 50PSI running, but the engine won't idle, so i can't get it to run for too long. With the FPG valve closed, it jumps to about 44PSI.

It seems to me it's likely I have a vacuum issue, maybe? If so, where should I start investigating? Nothing changed at all upstream of the CPR, so I'd have to imagine the first place I should investigate is the mixture unit and fuel distribution unit?

If your only getting 44 PSI with the fuel pressure test valve closed (RPM relay jumpered), that is a problem. Primary pressure regulator, fuel filter or fuel pump must bad. You should get 70 to 75 PSI.

rjd2
09-01-2017, 11:26 PM
is it possible this could be an electrical connection issue? when i retrace my steps, the only things that have been disconnected were the fuel distributor, mixture unit, and the related electrical harnesses. while i'm not ruling it out, if a part of the fuel delivery system has failed, it would have happened literally while i was replacing the thermister. the car idled perfectly right before i started the thermister job, and didn't hold an idle the very first time i attempted a start after the thermister job. it seems extremely likely that it would be related to the connections/disconnections related to that job.

Ron
09-01-2017, 11:32 PM
Just in case, did you ever check the routing for the CPR/WUR fuel line with the small banjo bolt ?

Bitsyncmaster
09-02-2017, 07:42 AM
is it possible this could be an electrical connection issue? when i retrace my steps, the only things that have been disconnected were the fuel distributor, mixture unit, and the related electrical harnesses. while i'm not ruling it out, if a part of the fuel delivery system has failed, it would have happened literally while i was replacing the thermister. the car idled perfectly right before i started the thermister job, and didn't hold an idle the very first time i attempted a start after the thermister job. it seems extremely likely that it would be related to the connections/disconnections related to that job.

What the thermistor in the valley does is set how wide the idle motor opens at when you turn the key on. If it was and open circuit, the stock idle ECU tries to hold the idle RPM at around 2500. You can test the resistance right on the idle ECU connector pretty easily. I don't think the thermistor would prevent the engine from starting.

Another electrical connection is the vacuum advance solenoid. It's common that connector falls off the solenoid when your moving the engine harness. You will get a poor idle if that connection is bad but it does not prevent the engine from starting.

Other connections are the ignition resistors which connect the ignition coil. Since your engine fires cold I would think these connections are OK.

An important ignition connection is the pickup coil in the ignition distributor. That coil connection goes to a two pin connector. On my car that connector was very corroded so bad, I just removed the connector and connected the wires. You should inspect that connector (pull it apart and look at the pins).

NckT
09-03-2017, 12:54 PM
If your only getting 44 PSI with the fuel pressure test valve closed (RPM relay jumpered), that is a problem. Primary pressure regulator, fuel filter or fuel pump must bad. You should get 70 to 75 PSI.

I've seen that and it was due to a split O ring(s) in the fuel distributor pressure regulator ie the usual problem for hot start problems.

rjd2
09-03-2017, 01:07 PM
hey NickT-I have a hunch you may be on to something....

So when I completed the job, I was left with one leftover O-ring. I could never figure out where it went. There's a ~1 1/2" o-ring that lies between the black fuel distributor body, and the top of the mixture unit(the downward shaft of the fuel distributor goes thru it). I got that one in place, but there was an identical size o-ring in the gasket kit, and i never figured out where it went. it's definitely behaving as though I have a vacuum issue. I'll try to re-read the manuals' diagram of the distributor/mixture section; in the meantime, if anyone has any leads as to where each of the o-rings to be replaced are in the mixture unit section, and which one i might have missed, that'd be great. thanks!

David T
09-03-2017, 02:32 PM
From the many posts in this forum concerning the Primary Pressure Regulator, it would seem, once you mess with the "O" rings, there is a high failure rate. I don't know if it is due to the replacement "O" rings not being the correct size, something about how the new ones are installed, or what, but once you touch that regulator it seems to become a problem if it wasn't before. IMHO the primary cause of loss of rest pressure is the fuel accumulator. Next would be the check valve at the fuel pump. Leaks are a possibility but they are very noticeable. The PPR is the LAST likely suspect unless it has been tampered with. Then it seems to become the #1 cause. Bottom line, unless you can rule out all other possible cause you should not touch that PPR.

Bitsyncmaster
09-03-2017, 02:52 PM
From the many posts in this forum concerning the Primary Pressure Regulator, it would seem, once you mess with the "O" rings, there is a high failure rate. I don't know if it is due to the replacement "O" rings not being the correct size, something about how the new ones are installed, or what, but once you touch that regulator it seems to become a problem if it wasn't before. IMHO the primary cause of loss of rest pressure is the fuel accumulator. Next would be the check valve at the fuel pump. Leaks are a possibility but they are very noticeable. The PPR is the LAST likely suspect unless it has been tampered with. Then it seems to become the #1 cause. Bottom line, unless you can rule out all other possible cause you should not touch that PPR.

I disagree. The PPR o-ring is the first thing you check. Takes about 10 minuets. The problem with the replacement o-rings was one vendor seemed to get some faulty ones.

The o-ring that makes or breaks the PPR is the little one on the end of the little piston. You remove the large hex cap carfully and you will pull a spring and some washers (used as shims). Then you have to pull the piston that remains in the distributor hole. The o-ring is on the bottom of that piston. Check for missing chunks and or splits on that o-ring.

NckT
09-03-2017, 04:59 PM
I disagree. The PPR o-ring is the first thing you check. Takes about 10 minuets. The problem with the replacement o-rings was one vendor seemed to get some faulty ones.

The o-ring that makes or breaks the PPR is the little one on the end of the little piston. You remove the large hex cap carfully and you will pull a spring and some washers (used as shims). Then you have to pull the piston that remains in the distributor hole. The o-ring is on the bottom of that piston. Check for missing chunks and or splits on that o-ring.

I agree with Dave. For what it's worth, I've setup the primary pressures back to spec on many D's now by adding additional shims to correct the preload of the aged spring to correct the primary fuel pressure to spec (or increased for performance exhaust) when setting the k-jet up, and by doing so have removed and re-fitted the same primary pressure parts and O rings and have never had a problem. It must be technique or something then. ..

A running engine with the fuel pressure gauge in the correct position with the isolator valve closed so the gauge reads the fuel pressure from the top fuel line of the fuel distributor, 44 psi (3 Bar) is still short of the 5.2-5.3 bar (75 to 76 psi) is still too low for the primary pressure so is either the regulator in the fuel distributor, blocked fuel filter/ constricted / blocked fuel pickup or knackered fuel pump.

Good luck sorting it

Bitsyncmaster
09-03-2017, 06:31 PM
I have checked many cars for primary pressure and they always seem to run at 68 to 70 PSI. Mine was the same way. I shimmed it up to 75 PSI also. I did not notice any improvement but I'm running a stock (mechanical wise) engine.

rjd2
09-03-2017, 09:31 PM
SUCCESS! SHE'S IDLING!

The o-ring provided with the intake rebuild kit didn't seat very well between the fuel distributor and the mixture unit body. I suspected it wasn't quite right upon installation, but didn't think much of it. It had about 1/4" of play. Luckily, I had a spare o-ring laying around that provided a nice snug fit there. Whew!!! Now, all I need to do is tune in my mixture/lambda setting, and I should be good to go for the foreseeable future, knock on wood!

Thanks to this whole community. You guys are the best!!!!! I don't think I would have solved this without you!!!

NckT
09-04-2017, 06:28 AM
Well done!

I'd still look into that fuel pressure again now the engine is running etc to make sure all is within spec etc

NckT
09-04-2017, 06:35 AM
I have checked many cars for primary pressure and they always seem to run at 68 to 70 PSI. Mine was the same way. I shimmed it up to 75 PSI also. I did not notice any improvement but I'm running a stock (mechanical wise) engine.

I noted that it affected the air to fuel ratio at the higher end of the rev range under load on a rolling road in 2009 at a "Euro tec" event here in UK that was repeatable on 10+ cars (oxygen sensor signal wire disconnected disconnected to negate closed loop feedback).

Adding the shims to spec was the best result for power / torque AFR compromise.

For stock k jet with a performance exhaust, it was found that increasing the primary pressure to 5.3 to 5.4 bar corrected the leaning out at the higher revs from 3500 to 6000 with standard fuel adjustment, both for lambda and non lambda k jet (for the 5 cars at the time of test on the dyno day). These have had repeatable results too since then, so the re shimming is worthwhile for sure. We've had to get the shims specially made though in 0.25mm .5mm 1.0mm thicknesses so that the pressure can be done within the spec.

Bitsyncmaster
09-04-2017, 07:00 AM
I noted that it affected the air to fuel ratio at the higher end of the rev range under load on a rolling road in 2009 at a "Euro tec" event here in UK that was repeatable on 10+ cars (oxygen sensor signal wire disconnected disconnected to negate closed loop feedback).

Adding the shims to spec was the best result for power / torque AFR compromise.

For stock k jet with a performance exhaust, it was found that increasing the primary pressure to 5.3 to 5.4 bar corrected the leaning out at the higher revs from 3500 to 6000 with standard fuel adjustment, both for lambda and non lambda k jet (for the 5 cars at the time of test on the dyno day). These have had repeatable results too since then, so the re shimming is worthwhile for sure. We've had to get the shims specially made though in 0.25mm .5mm 1.0mm thicknesses so that the pressure can be done within the spec.

+1...good info.

I had to add quite a lot of shim to get mine up to 75 PSI.

rjd2
09-04-2017, 08:24 AM
Well done!

I'd still look into that fuel pressure again now the engine is running etc to make sure all is within spec etc

yea, i probably need to. i left the fuel pressure gauge on after i got it to idle, and the at rest/off PSI was around 40; it held there basically indefinitely once the engine was off.

rjd2
09-16-2017, 08:25 PM
Reporting back after further shakedown. Here's where I'm at:

-fuel pressure= ~40 at rest, ~65 at run, and stable.
-dwell looks solid right around 40-42 degrees.

the only strange thing i'm seeing is this: I took it out for a 30 minute shakedown. the idle was solidly in the 750-ish range, EXCEPT for about a 2 minute period in which it was goosed to about 3000RPM. I'd never seen it pegged this high. It gets stranger-it went away after about 2 minutes, and went back to 750-ish for the rest of the trip. To recap, new CPR, new thermister, new gaskets, new fuel lines. My hunch here is something physically sticking in the throttle linkage somewhere, intermittently. I don't really know where else to check, other than right at the spindle. The spindle, and the bar that links off of it, seem to operate normally; I can manually check the throw of it when it's running, and it gooses the RPM's. Any ideas? Where do I physically check for any possible throttle cable stickiness? Thanks!

Bitsyncmaster
09-16-2017, 09:05 PM
Reporting back after further shakedown. Here's where I'm at:

-fuel pressure= ~40 at rest, ~65 at run, and stable.
-dwell looks solid right around 40-42 degrees.

the only strange thing i'm seeing is this: I took it out for a 30 minute shakedown. the idle was solidly in the 750-ish range, EXCEPT for about a 2 minute period in which it was goosed to about 3000RPM. I'd never seen it pegged this high. It gets stranger-it went away after about 2 minutes, and went back to 750-ish for the rest of the trip. To recap, new CPR, new thermister, new gaskets, new fuel lines. My hunch here is something physically sticking in the throttle linkage somewhere, intermittently. I don't really know where else to check, other than right at the spindle. The spindle, and the bar that links off of it, seem to operate normally; I can manually check the throw of it when it's running, and it gooses the RPM's. Any ideas? Where do I physically check for any possible throttle cable stickiness? Thanks!

Fuel pressures look acceptable. You should have more primary pressure but that is not causing your problem.

Dwell on a warmed up engine should be swinging back and forth pretty quickly about 30 to 40 degrees or more. If it's solid around 41 degrees something is wrong with the lambda circuit.

You can set your throttle spool spring to the tighter selection. On my car where the throttle cable was clamped on the passenger side valve cover, that clamp had worn through the rubber cover on the cable and rusted the metal shield causing sticking. Also put some grease on that throttle spool spring and it's less sticky.

David T
09-17-2017, 09:38 PM
Lubricate the throttle cable as per the recall. Take the throttle spool apart, clean up all of the old grease and relubricate it. If the quadrant link is very worn readjust it so it solidly pushes the throttle arm to idle. You will have more play in the throttle but you will always get back to idle. Tighten the spring as a last resort. Long drives with a heavy spring is hard on the feet. The system already has 3 springs in it and if it is working correctly they should be enough.

rjd2
10-03-2017, 08:33 AM
Further shakedown has been done over the last few weeks. Problem persists. Here's where it is, and what I've done:

the problem: when the engine reaches a certain temperature, it will kick the idle VERY high. It usually pegs around 3k. I've done 4 shakedown drives now, and it always does it about 10-12 minutes in. I let the car idle in my driveway for the same period of time, and it did not go high. I have had the problem alleviated 2 times; once, it stayed high for a few minutes, and then came down on it's on mid-drive(I did not turn the engine off). The 2nd time, I stopped the car>shut the engine off>inspected the spool>restarted it-the idle went back to normal(with a wider hunt than I'd expect, but still averaging ~750-ish).

Per you guys' advice, I went over the spool, and the cable, lubricating the cable, and tightening the spool. It seems to have no corrosion, and we've checked its' motion visually-the spool and cable are almost surely working properly.

Any ideas where to check next? O2 sensor? ECU unit? I'm kind of at a loss. (Not sure if this is helpful, but the engine bay seems to get fairly hot after a 10-15 minute drive; hotter than I'd expect.) Thanks for the help!

Bitsyncmaster
10-03-2017, 09:28 AM
My guess would be your temp sender has a bad connection. You can jumper that sender at the idle ECU to test. Or the ECU itself is bad.

David T
10-03-2017, 10:51 AM
If the idle changes without touching the throttle it could be a "hicccup" in the idle motor system from a bad connection. Make sure the throttle decel springs are not burnt up too. Doubt it would be the temp sender for the idle ECU, it is not supposed to be able to change the idle that much.