Log in

View Full Version : M12 1.5 Thread chaser



sdg3205
12-05-2017, 12:37 AM
Anyone have a good recommendation for an M12 x 1.5 thread chaser? I'm having a lot of trouble finding one locally, and I've called all the local fastener and tool stores. Lots of taps, but no chasers.

I need to clean out my head bolt block threads.

Delorean Industries
12-05-2017, 12:48 AM
You need a tap not a chaser. Threads need to be cut further into block. Other wise head bolts will bind and provide false torque readings.

Bitsyncmaster
12-05-2017, 08:05 AM
I just grind most of the taper end off a tap and use that to chase the threads. That lets me also tap the holes better at the bottom if it's not a through hole.

Nicholas R
12-05-2017, 11:05 AM
I just grind most of the taper end off a tap and use that to chase the threads. That lets me also tap the holes better at the bottom if it's not a through hole.

Or you could just buy a bottoming tap. :wink:

Bitsyncmaster
12-05-2017, 11:44 AM
Or you could just buy a bottoming tap. :wink:

Have not seen them locally. I actually don't buy the store brand taps except for chasing. The big name taps work so much better when tapping new threads.

nullset
12-11-2017, 05:20 PM
You need a tap not a chaser. Threads need to be cut further into block. Other wise head bolts will bind and provide false torque readings.

Any particular brand or model of tap you'd recommend?

(I don't have a set....)

nullset
12-11-2017, 05:24 PM
Would something like this be sufficient?

https://www.amazon.com/Uxcell-Flute-12mmx1-5mm-Metric-M12x1-5mm/dp/B00AUB7LGU/ref=sr_1_3?ie=UTF8&qid=1513027349&sr=8-3&keywords=m12-1.5+tap

Bitsyncmaster
12-11-2017, 06:56 PM
Any particular brand or model of tap you'd recommend?

(I don't have a set....)

Look on a machinist tool supply company. A good set will set you back big $$. Your probably better just buying a bunch of the common sizes you need.

David T
12-11-2017, 10:22 PM
If you go to a large auto supply they should have it but you may have to buy a whole kit to get just the one size. Or they could order it for you.

sdg3205
12-12-2017, 12:17 AM
I found something locally

dn010
12-12-2017, 10:53 AM
I buy the cheap kits and use them until they break. This current kit posted below has lasted me 5 years and it's cheap enough to replace if needed.

https://www.amazon.com/ABN-Titanium-Tap-Hexagon-Metric/dp/B01N4FTVCZ





Would something like this be sufficient?

https://www.amazon.com/Uxcell-Flute-12mmx1-5mm-Metric-M12x1-5mm/dp/B00AUB7LGU/ref=sr_1_3?ie=UTF8&qid=1513027349&sr=8-3&keywords=m12-1.5+tap

Flash66
12-12-2017, 01:48 PM
An old school way to make a chaser is to just hit the sides of an old head bolt or just a 12x1.5 bolt off the shelf with a cutoff wheel flattening the threads on 2 sides.

Nicholas R
12-12-2017, 03:18 PM
I buy the cheap kits and use them until they break. This current kit posted below has lasted me 5 years and it's cheap enough to replace if needed.

https://www.amazon.com/ABN-Titanium-Tap-Hexagon-Metric/dp/B01N4FTVCZ

For chasing, absolutely; for tapping, no way. Nothing like making a tapped part only to have a tap break off while cutting new threads. At that point there's practically nothing you can do but completely start over.

opethmike
12-12-2017, 04:01 PM
I just hammer stuff together with big nails.

Shep
12-15-2017, 12:36 AM
I just hammer stuff together with big nails.Gluestick and important legally-binding documents! :biggrin: