Log in

View Full Version : Sacrilege? Cutting up a pair of Delorean Dunks for what???



Michael
09-22-2011, 12:58 AM
Yup, I decided if I'm going to wear them, they better have something going on. I thought about this for some time, and since I have 3 pairs of DMC dunks in my size(including a press release box pair), I decided to start wearing a pair. Now that they are somewhat broken in I am going to do something I thought should have been done from the start to live up to the hype....ADD DOOR LIGHTS!!! I will add 3 door lights to each shoe. They will be centered on the front/rear/and outside of the black sole. A small rechargeable li-po battery encased in the sole will power each shoe.

I think the Nike Mag release pushed me along to do this. There are only 6 weeks of cruise ins left so I would like to have these done to wear in time, I doubt I would wear them lit up anywhere else but a car show. I will spend the next week or so on these. I mocked up a prototype pair and yes it will work! Construction starts this weekend!

The goal: install these
http://dmctalk.org/attachment.php?attachmentid=5363&d=1316662422

Onto these:
http://dmctalk.org/attachment.php?attachmentid=5364&d=1316662439

To begin, I bought batteries. I had LED's and plenty of resistors. I wired up a simple test circuit to see if my batteries would power them for an extended period:
http://dmctalk.org/attachment.php?attachmentid=5366&d=1316662473

Here are my batteries: 3.7V 1s Li-po batteries 500mAh. Pretty tiny! They will power the shoes for at least 6-8 hours!
http://dmctalk.org/attachment.php?attachmentid=5358&d=1316662349

My LED's wired up and ready
http://dmctalk.org/attachment.php?attachmentid=5356&d=1316662316

A switch I installed in my mock-up shoe..not sure how or if I will use a switch, or simply pull back the sole liner and connect the JST plug on the battery.
http://dmctalk.org/attachment.php?attachmentid=5355&d=1316662298

A cutout has been made so the battery fits flush in the shoe(the liner covers this)
http://dmctalk.org/attachment.php?attachmentid=5360&d=1316662380
A idea of what they will look like on my mock-up. Note I have not cut the lens to size yet.
http://dmctalk.org/attachment.php?attachmentid=5362&d=1316662409

I hope to have the lights installed this weekend, and maybe have the lenses cut and finished by the end of next week. I'm using bicycle pedal reflectors for the lenses, and once they are cut, I will secure a black trim around them, (just like the car) before attaching them to the shoes.

dvonk
09-22-2011, 01:58 AM
creative idea! im interested to see the final product.

Dracula
09-22-2011, 02:28 AM
To play Devil's Advocate, wouldn't a better mod for wearability of the shoes be something that makes them more comfortable?

Despite my typical stance against cutting up or destroying anything that's inherently rare, I see no reason not to do this. The only thing about the shoe that's really special is the tail light pattern on the bottom and I'd imagine that would wear off very quickly in actual use. Even if it doesn't, that's one of the least visible areas on the shoe. I suppose, though, my lack of concern for them comes from the fact that they were never made to be worn as shoes. I can't understand this or shoe collectors, so my opinion is "have at it." I know you're not seeking approval; aside from a shoe collector forum, (which I'm assuming exists,) this is the last place you'd post if that was your intent.

My suggestion; get a stainless computer switch that mounts flush and use that for your control; something like this one:

http://www.tme.eu/u/NewProducts1/przyciski_wandaloodporne_male.jpg

You'd also be adding some actual stainless to the shoe that way.

yellowmxwheels23
09-22-2011, 01:14 PM
I can't understand this or shoe collectors

Shoe collecting is pretty easy to understand. You buy a pair of shoes for say $125.00 in a few years you turn around and sell them for $500.00.
There's 2 different kind of shoe collector. One will buy shoes and never wear them hoping they picked something up they can triple their money on when they sell them. The other will buy a ton of shoes to wear once or twice, mix in a few he will never wear or sell.
It's kinda like playing the market.
I've had shoes that I held onto for a long a long time that made me some pretty good money. I'm talking like upgrade to a stage 2 kind of money. Can't really say that about many stocks. I did buy into Sirius satelite radio at .8 per share and sold when it was leveling off at $2.15 per. My Disney stock will always hold its own but you can't be certain on any stock. Shoes you can be certain of, if you pick up something that has a limited release, rare colorway,actual 1-23 Air Jordan, Dunks, etc.. your going to make money. Thats all there is to understand about shoe collecting.

Dangermouse
09-22-2011, 01:23 PM
So it's more shoe investing than shoe collecting?

Dracula
09-22-2011, 01:41 PM
I understand you can make money off of it, just like you can with anything, but doesn't it severely hurt the value of a pair of shoes if you wear them?

I collect a lot of things; vintage stereos, cars, watches, and a lot of other things. The big difference is that I'm able to use my 100+ year-old watch on a regular basis and it doesn't hurt the value. Heck, my best watch has enough gold that its scrap value is comparable to a new Rolex, yet I use it every time I put on my Civil War uniform. The same goes for some of my stereos. I have a non-US-market '70s Pioneer tuner and cassette player that are a matching pair and both work quite well, so I use them when I'm going through my daily routine, cleaning, or just want to hear some music. I paid $50.00 for the pieces, reworked them a little, and could sell them at $300.00 minimum any day (before the economy got tight.)

I suppose it just comes down to the fact that I can't see buying anything solely as an investment and, though it serves a clear purpose, not using it for that. I get that the shoes are made to be collectible, yet if they're not worn, they're made for nothing, or some are so rare that people won't wear them. It may be a good form of investing, but it seems to me a lot like buying a painting you can't stand the looks of because you think it'll go up in value.

SoCalDMC12
09-22-2011, 03:38 PM
Some collectors see certain shoes as art, and want to preserve them. While I can understand this, I agree that it's kind of a shame to simply buy them to store away. Kinda like having a car that never leaves the garage. But, to each his/her own... whatever makes ya happy!

Oh... neat mod... looking forward to seeing the end result!

sean
09-22-2011, 03:41 PM
Eagerly looking forward to the results!

SIMid
09-22-2011, 07:29 PM
Eagerly looking forward to the results!

+1

Even though I don't have a pair (which I do want them), interested in your final creation.

Bitsyncmaster
09-22-2011, 08:18 PM
My wife needed a new battery for her old cell phone. Got 4 of them on Amazon for only 2 or 3 bucks each. I think they are smaller (thinner but wider) but have more power than yours.

model
LGLP AHKM

Michael
09-22-2011, 09:55 PM
My wife needed a new battery for her old cell phone. Got 4 of them on Amazon for only 2 or 3 bucks each. I think they are smaller (thinner but wider) but have more power than yours.

model
LGLP AHKM

Not exactly. Most phones today use LI-on(Lithium Ion) batteries which are very similiar to Lithium Polymer batteries. There are differences in the way the cell is contained, but for the most part they are the same. Li-on's are generally cased in a hard shell, with no leads but contacts...making it very difficult for my uses. Li-po batteries are vacum sealed in a soft pouch with power leads, to which any sized connector can be used. Power is the same for both, each cell is rated at 3.7v, and can be multiplied with the addition of extra cells, but for running 3 LED's which are rated at 3v, a single 1s 3.7v battery is more than needed. I was going to run them in series and try to skip the resistor but the voltage would fluxuate too much during discharge, and was still too high on a fresh battery, so I decided to use a resistor and run them parallel.

The sizes are comparable based in mah ratings. My 500mah battery should run my 3 lights for at least 6 hours, and probably more. I hooked them up for 2 hours and saw a .2v drop in my battery. Minimum discharge for a lipo is +/- 3v so at maximum charge of +/- 4v and the current draw of the 3 lights, I'm good to go.

Another advantage for me using LIpo batteries is I can quick charge them on my charger, which is adjustable between 1 and 6 cells and infinate mAh ratings, so I get a perfect charge everytime, in 1 hour(based on a 1c charge) Most LIon packs use a smart charger that trickle charges at a set rate(usually 1/2c or less), and is designed specifically for a certain pack, which usually plugs into the phone.

Bitsyncmaster
09-23-2011, 08:52 AM
Thanks for that info on LIpo batteries. Learn something new every day.

I know my camera batteries are about 5 watt/hours so I was just assuming the cell phones are the same.

You definitely want a current limit resistor with a 3.7 volt battery on an LED. Most blue and white LEDs run around 3 to 3.5 volts at 20 ma and red and blue run about 2 to 2.2 volts. So you could not string them without going to a higher voltage battery.

Michael
09-24-2011, 12:49 AM
Completed my first circuit tonight. Didn't take long, and I would have done both had I had another battery jack on hand.

I laid out a pattern using my DMC shoe and marked out where my lights, battery, and connection jack would lie. I wanted to make sure to keep the center light locations out of the places the shoe will flex, and give ample wire length in the toe area to compensate for the stretching when I walk in them.
http://dmctalk.org/attachment.php?attachmentid=5405&d=1316835853

20 minutes later I have a circuit ready for installation. I left the wires a little long on the front, I will have to go back and taek about an inch off of them. Once I get my lenghts perfected and test mounted in the shoes, I will encase the led leads in hot glue to prevent wear.
http://dmctalk.org/attachment.php?attachmentid=5406&d=1316835871

Next step is drilling holes in my Dunks:shocked:

Michael
09-25-2011, 10:21 PM
Couple of teaser pics. Got the lights installed, but I ended up putting the battery inside the folds of the upper shoe liner. This meant I didn't have to cut a cavity in the shoe. The battery is so thin that you don't even feel it there. I will have to re-wire my wiring harness, but that's easy to do. I just temporarily placed a few lenses in place. The real lenses will be thinner and finished on the sides with black rubber trim. This will make them look just like the car lights and prevent light leaks.

dvonk
09-26-2011, 01:40 AM
progress looks good! :thumbup:

just a thought: have you considered using LEDs that match the lens color instead of plain white? it should provide a richer color. (you probably already know this, being a master model builder and all. :wink:)

Michael
09-26-2011, 09:05 AM
progress looks good! :thumbup:

just a thought: have you considered using LEDs that match the lens color instead of plain white? it should provide a richer color. (you probably already know this, being a master model builder and all. :wink:)

Thank you! I did consider using colored LED's but the MCD output(brightness) is much lower for red and orange than white(which is the brightest). If I remember correctly, orange is around 5,000 mcd, while the white is 20,000 mcd. I may however scuff the bulbs and paint a coat of transparent orange over the bulbs to knock the blue hue out of them.

Dracula
09-26-2011, 10:11 AM
That's looking pretty neat. It sure gives the shoes a more unique touch and something that would help justify the price. Too bad there's not going to be a comfortable, wearable production run of those shoes.

On a semi-related note, now I want to add lights to a pair of Converse High-Tops.

RIUM+
09-29-2011, 12:19 PM
Be careful about squishing that battery. LiPo batteries are usually more fragile than standard Li-Ion batteries... Ones in a squishy case like that may seem flexible but bending/squishing/damaging them is a quick way to cause spontaneous combustion.

I say this as someone who now keeps his 11.1v 4500mAh 25C LiPo batteries in a flame-retardant bag after I once dropped one... Those weren't standard LiPo batteries though (obviously, since they were designed to output 100+ amps!). I'd just hate for you to end up with burns on your feet!

Michael
09-30-2011, 12:56 AM
Be careful about squishing that battery. LiPo batteries are usually more fragile than standard Li-Ion batteries... Ones in a squishy case like that may seem flexible but bending/squishing/damaging them is a quick way to cause spontaneous combustion.

I say this as someone who now keeps his 11.1v 4500mAh 25C LiPo batteries in a flame-retardant bag after I once dropped one... Those weren't standard LiPo batteries though (obviously, since they were designed to output 100+ amps!). I'd just hate for you to end up with burns on your feet!

Thanks, but I'm pretty versed in lipos and I have been around them for several years now. I keep mine in a fireproof safe, including several 22 volt 6 cells...those things I use for my f16 jet. That's why I originally put the batteries under the arch(where pressure is the least) but later decided to sew an extra flap in the side. The 1s battery I'm using is so small, it can go just about anywhere.

I got some more done today, including dry fitting my lenses in one shoe. I wanted them to be slightly recesses, so I cut a recessed compartment for the lenses to fit neatly. The next step is to fill the bulb cavity with silicone or hot glue, which will return any strength that may have been lost due to the holes drilled. I'm not sure what to glue to use to secure the plastic lenses. I need something that bonds to rubber well.

Here is what we have so far, I still will paint the edges with automotive paint in flat black which will clean it up a lot.

Michael
10-01-2011, 12:29 AM
Almost there, all I need to do is fill the soles with hot glue to permanetly secure the LED's and fill the voids, and glue my lenses in place. I pretty much decided not to outline the edges in black because once I got the lenses in place, I like how they light up. This way if you see it from the side, you can see the front and back lights as well.

First, my lenses had raised lettering on them, so it was ground off, and refinished. Here is a pic before final polishing shown next to an unfinished lens. You can see the lettering on the bottom lens, which will be smoothed off and polished:
http://dmctalk.org/attachment.php?attachmentid=5633&d=1317438848

Here is a pic of the LED's painted transparent red. This does two things: It knocks off the bluish hue the white LED's produce and tones down the brightness just a tad, as well as keeping the orange side markers from looking yellow.

Notice also the recessed opening to keep the lens nice and tidy looking once it is in place.
http://dmctalk.org/attachment.php?attachmentid=5636&d=1317438868

The DMC Dunk 6.1...almost ready for wear!! Here you can see what I mean by the side view. The front and real lights are still visible:
http://dmctalk.org/attachment.php?attachmentid=5635&d=1317438861

I should have them done by Sunday evening. The only thing holding me up is I left my glue gun at church a few weeks ago.

Michael
10-03-2011, 10:14 PM
Finished! Walked around in them all day today to test them out and make sure there were no bugs to be worked out. Don't worry, I didn't use the shoes that came with the Hyperstrike press box, they are still in their shrink wrap.
http://dmctalk.org/attachment.php?attachmentid=5715&d=1317690430
http://dmctalk.org/attachment.php?attachmentid=5710&d=1317690307
http://dmctalk.org/attachment.php?attachmentid=5713&d=1317690391
http://dmctalk.org/attachment.php?attachmentid=5714&d=1317690404
http://dmctalk.org/attachment.php?attachmentid=5716&d=1317690464

Ozzie
10-03-2011, 10:16 PM
Looks great!
Good job.

dvonk
10-04-2011, 01:09 AM
personally, i like them better than the originals. good job! :thumbup:

SoCalDMC12
10-04-2011, 06:07 AM
Very nice job!

xbrules
10-04-2011, 08:08 AM
Very very awesome, Just what they needed too. I wonder how many requests you are gonna get for retrofitting door lights to DeLorean dunks? haha Great job once again ;)

Michael
10-04-2011, 12:01 PM
Thank you! I don't think I will build any more pairs, it was kind of a one time thing. I really don't know if I will even wear them, except maybe to a cruise in or car related event. I doubt I would wear them in any other public venue(lighted up), unless I wanted to embarrass my wife :)

I do want to take some pictures of them with my car and make them look professional.

SIMid
10-04-2011, 10:40 PM
Great job! Looks cool too! Well done! :)

Dangermouse
10-05-2011, 08:56 AM
Great job Michael. very well done.

However the first thing I thought off was "shouldn't the front ones be white instead of yellow" ?? Tiny little headlights....:rock_on:

sean
10-05-2011, 09:11 AM
Great job Michael. very well done.


+1! Initially I thought it was a cool idea but when you roughed it out it looked off but the finished product looks great!