View Full Version : Any airbag retro fits done by DMC?
About time
01-09-2019, 09:19 PM
I looked at there site and don't see them doing any retrofit upgrades for safety reasons? I'm also scratching my head saying, If they are really a "New Car company" why don't they make some upgrades like they did with the seats?
I think it would only help the brand and enhance desire to own one.
dn010
01-09-2019, 09:26 PM
There is a lot involved when it comes to air bags. Sensors. Computer. Air bag units. Wiring. And then there is testing. After all that, replacement and maintenance every time an 'air bag light' goes on. The cost of all this is most likely too great.
dmcnc
01-09-2019, 09:30 PM
^adding to the cost, touching anything that affects the car's safety rating in any way is opening yourself up to a lawsuit. The fuel pump recall is a good example. I don't see how the risk would be profitable in the long-run.
David T
01-09-2019, 10:19 PM
The engineering and testing to verify an SRS (Supplemental Restraint System) is prohibitive for a small company never mind the insurance that would be necessary to cover any Liability claims. If something like the Takata debacle happened it would wipe out DMC. In the regs for small manufacturers the SRS is not required just because of the huge costs involved. It was successfully argued it would prevent small manufacturers from existing in the first place if SRS was a requirement.
DMC-81
01-09-2019, 10:30 PM
Ironically, according to the article in this thread, http://dmctalk.org/showthread.php?17098-Interesting-article-on-the-man-amp-the-car , early on in the formative stages of the car, Allstate gave JZD some funds to build a safer car, and I understand that airbags were crash tested in the Delorean during development. You can see the the airbag deploy in this video:
https://www.youtube.com/watch?v=z524AipITiM
That's pretty good for 1980.
vwdmc16
01-10-2019, 04:22 AM
Air bag science and understanding was in an extremely primitive form 38 years ago. There's not a way to Simply retrofit airbags into a another vehicle, the setup and Design and even programming of an airbag system is down to the millisecond is not something you can just slap into another car like a different set of exhaust tips. At least not without millions of dollars of testing and engineering.
I also read about the 40 mile an hour crash test video, the one that looks really horrific. The the car had a faulty door latch that they knew about but didn't to bother fix. That pretty much voided the entire test as the structural rigidity of the compartment cabin pretty much went down to nil. The only benefit of it was really only stressing the importance of having properly working door latches in case of a catastrophic accident in a Delorean.
I think they were just betting on the airbag technology of the future to take care of everything. But putting an explosive in a kevlar pillow case wont be enough if you don't wear your seatbelt or properly latch your door.
Remember this new low production bill is really only intersting or plausible to companies like DMC is because it does not require safety updates, just emission updates.
Michael
01-10-2019, 09:36 AM
LOL...would you seriously want an explosive bomb made by DMCH mounted 1 foot in front of your face?
Nicholas R
01-10-2019, 10:10 AM
LOL...would you seriously want an explosive bomb made by DMCH mounted 1 foot in front of your face?
This is my exact thought. Not the DMCH part specifically, but just that I wouldn't want to ride in any car that had an air bag willy nilly stuffed up front. Automakers to extensive testing to be sure their airbags help people, instead of hurt them. Without testing, it's just a bomb inside of a bag like Michael said. Heck, even with testing you can still end up with issues; (as indicated by the airbag recalls on both my Ranger and my Civic).
After typing this out, I'm now also assuming there there are likely DOT and legal reasons why DMCH couldn't simply add airbags to the car without an excessive amount of design and testing. Never going to happen.
Dangermouse
01-10-2019, 10:31 AM
There's a reason why PepBoys sell aftermarket reversing cameras, HUDs, LED lighting and "carbon fiber" parts and not aftermarket airbags.
That would be terrifying.
AugustneverEnds
01-10-2019, 02:37 PM
Driving entails risk. Buckle up and proceed accordingly.
About time
01-10-2019, 04:26 PM
Funny how most only bring up the most difficult change/modification to make, adding a back up camera, side warning sensors, LED headlights could all be done IMO without much trouble. Also odd how they tested cars with airbags, no car company makes airbags yet a few laugh about how DMC would screw it up.
Michael
01-10-2019, 04:36 PM
You know what? I asked a similar question several years ago about why on the world we have all these accessories like luggage and stainless dress up parts but after 30 years nobody made a desperately
needed transmission filter. A friend wrote me back and said "why don't you make one?"
So I did. I weighed the cost and liability issues vs the small reward of profit and did it. So my question to you is "Why don't you make one sport?
When someone who has a crash in one of the cars equipped with an "about time" airbag decides to sue you and although you may be completely innocent, will go bankrupt defending yourself in court, maybe then you will find the answer to your question.
Funny how most only bring up the most difficult change/modification to make,...
Funny how those who wonder out loud "why doesn't someone do this or that" grow silent when they have to write the check and take all the risks to make it happen.
Michael
01-10-2019, 04:51 PM
Three words:
"Lucas powered airbags"
AugustneverEnds
01-10-2019, 04:54 PM
Three words:
"Lucas powered airbags"
Dear God/Allah/Buddha/Elvis Presley
Dangermouse
01-10-2019, 06:21 PM
Three words:
"Lucas powered airbags"
Historically speaking, that just means that they would never work :)
Or they would catch fire.
dn010
01-10-2019, 07:07 PM
Funny how most only bring up the most difficult change/modification to make, adding a back up camera, side warning sensors, LED headlights could all be done IMO without much trouble. Also odd how they tested cars with airbags, no car company makes airbags yet a few laugh about how DMC would screw it up.
Its no secret that DMC was experimenting with air bags from the beginning. Read the books (stainless steel illusion, etc.) if you want to know more about the DeLoreans built with airbags that they were testing and John's decisions.
If you don't like the answers you're getting here then it's probably best to call DMCH themselves and ask why they're not putting airbags in their 'new builds'. 1.800.872.3621. Please let us know what they tell you.
About time
01-10-2019, 10:14 PM
Its no secret that DMC was experimenting with air bags from the beginning. Read the books (stainless steel illusion, etc.) if you want to know more about the DeLoreans built with airbags that they were testing and John's decisions.
If you don't like the answers you're getting here then it's probably best to call DMCH themselves and ask why they're not putting airbags in their 'new builds'. 1.800.872.3621. Please let us know what they tell you.
I'm fine with the answers, it's the limited scope some are latching onto. They take one item and blow me up as if there were no other items that could be improved, talked about designed etc.
Thanks for the info.
Dangermouse
01-10-2019, 11:00 PM
Bbuuttt the title of the thread specifically says “any airbag retrofits done “?
I also read about the 40 mile an hour crash test video, the one that looks really horrific.
It looks bad, but the engineeering firm that conducted the tests said the car actually did very well. Data from the crash test dummies suggests injuries that were well within acceptable limits at the time, and cabin deformation was minimal.
Mark D
01-11-2019, 02:50 PM
My first reaction to this thread was first to ask "why?" and then to laugh out loud given DMCH's spotty history with bringing new products to market. I can't hate on them too much because it's not like they have a dedicated engineering department at their disposal to actually design much. They seem to rely heavily on the vendors who manufacture their reproduction parts to carry the design burden. After the production work is completed it's not like they have an advanced quality control department either to verify what they are receiving meets the required specs.
That being said, a few years back I did some design work related to frontal and side impact crash testing. Essentially we were trying to use a developed air bag system from one vehicle and adapt it to fit another vehicle without having to create a completely new program/profile for the truck. The ECU that controls the air bags is specific to each vehicle and determines the timing and deployment rate for the air bags during a collision. Initial impact speed and deceleration rate at set intervals during the impact are what typically determine the profile and if the airbags will fire or not.
We were adapting an existing system I think we did half a dozen actual crash tests for this one vehicle at three different impact speeds. This was for a heavy duty truck and not a passenger vehicle but the relative complexity of the system was about the same. Had we started from scratch to develop a crash profile it would have meant between 10-15 impact tests. Most of the instrumentation and impact testing was contracted out to a specialized company that we worked along side as we made modifications to the vehicle design so it would match the existing crash profile. The development time took about a year and the bill at the end was high six figures, approaching seven.
SO, if DMCH or anyone else were to attempt anything like this they would be looking and destructive testing on a handful of cars as well as an enormous bill at the end. Given that there is no law or regulation requiring airbags, what would be the point? I'm not sure I understand how airbags would "enhance the brand" or the "desire to own one". I'm genuinely interested to hear opinions though if anyone thinks this is actually a good idea.
eight8toy
01-11-2019, 03:04 PM
I'm genuinely interested to hear opinions though if anyone thinks this is actually a good idea.
Nah.
I liked the rest of your comment though, interesting stuff!
dn010
01-11-2019, 03:12 PM
Just be thankful the airbags never made it into production. By now they'd surely be going off in your face while you're innocently driving down the road, like some Volvo 780 Bertone airbags do (due to sitting & water intrusion - does that sound familiar?).
David T
01-11-2019, 10:56 PM
My first reaction to this thread was first to ask "why?" and then to laugh out loud given DMCH's spotty history with bringing new products to market. I can't hate on them too much because it's not like they have a dedicated engineering department at their disposal to actually design much. They seem to rely heavily on the vendors who manufacture their reproduction parts to carry the design burden. After the production work is completed it's not like they have an advanced quality control department either to verify what they are receiving meets the required specs.
That being said, a few years back I did some design work related to frontal and side impact crash testing. Essentially we were trying to use a developed air bag system from one vehicle and adapt it to fit another vehicle without having to create a completely new program/profile for the truck. The ECU that controls the air bags is specific to each vehicle and determines the timing and deployment rate for the air bags during a collision. Initial impact speed and deceleration rate at set intervals during the impact are what typically determine the profile and if the airbags will fire or not.
We were adapting an existing system I think we did half a dozen actual crash tests for this one vehicle at three different impact speeds. This was for a heavy duty truck and not a passenger vehicle but the relative complexity of the system was about the same. Had we started from scratch to develop a crash profile it would have meant between 10-15 impact tests. Most of the instrumentation and impact testing was contracted out to a specialized company that we worked along side as we made modifications to the vehicle design so it would match the existing crash profile. The development time took about a year and the bill at the end was high six figures, approaching seven.
SO, if DMCH or anyone else were to attempt anything like this they would be looking and destructive testing on a handful of cars as well as an enormous bill at the end. Given that there is no law or regulation requiring airbags, what would be the point? I'm not sure I understand how airbags would "enhance the brand" or the "desire to own one". I'm genuinely interested to hear opinions though if anyone thinks this is actually a good idea.
My point exactly but in addition DMC would have to have Product Liability insurance to cover any problems. That one thing, never mind all of the testing required, is a killer. In today's litigious world insurance can be ruinous. A person who would have died but for the airbag, and gets some non-life threatening injuries, will sue for millions. It is usually cheaper when they die. In the early days of airbags people got terrible leg injuries in crashes that previously would have killed them. Automakers had to redesign the cars to prevent those injuries. Another case of the Law of Unintended Consequences. Wait till you see self driving cars. Less people will die but it won't prevent every death. The lawyers will reap huge benefits though.
jawn101
01-12-2019, 01:25 PM
Hey guys, I just ran across these pics. It looks like someone may have already taken the initiative on this project. The fit and finish... leaves something to be desired... but the branding is on point and I have no doubts at all that the safety of the implementation is top-rate.
Check it out - dual front and even side airbags! Sign me up
https://i.imgur.com/fBTblvY_d.jpg?maxwidth=640&shape=thumb&fidelity=medium
https://i.imgur.com/qtX51ZU_d.jpg?maxwidth=640&shape=thumb&fidelity=medium
https://i.imgur.com/sMjQcK1_d.jpg?maxwidth=640&shape=thumb&fidelity=medium
David T
01-12-2019, 01:52 PM
The actual installation of the hardware is not the problem. As has been pointed out, it is the software and how and when the airbags get deployed that is the crux of the problem. Without a LOT of design engineering and testing to validate it you could be adversely affecting safety, not improving it. Inside the airbag is is essentially a rocket motor and the exhaust is contained by the bag. If it was to go off inadvertently it can cause injuries, not prevent them. For those who are safety conscious the diligent use of seat belts is your best bet for survival in a crash even if the car has airbags. If the airbags go off and you are not restrained into position the airbag can kill you or you could be ejected from the car cutting your chances of survival greatly. Airbags are not a substitute for seatbelts, only an enhancement to help reduce injuries. If you won't drive in a car without airbags then you should probably sell your Delorean.
DavidProehl
01-12-2019, 01:56 PM
Hey guys, I just ran across these pics. It looks like someone may have already taken the initiative on this project. The fit and finish... leaves something to be desired... but the branding is on point and I have no doubts at all that the safety of the implementation is top-rate.
Check it out - dual front and even side airbags! Sign me up
https://i.imgur.com/fBTblvY_d.jpg?maxwidth=640&shape=thumb&fidelity=medium
https://i.imgur.com/qtX51ZU_d.jpg?maxwidth=640&shape=thumb&fidelity=medium
https://i.imgur.com/sMjQcK1_d.jpg?maxwidth=640&shape=thumb&fidelity=medium
Great find! Maybe if you can track down the owner of that car they would build out some kits for us. There is a thumbs up in the first photo so it must be safe enough right?
jawn101
01-12-2019, 02:05 PM
Great find! Maybe if you can track down the owner of that car they would build out some kits for us. There is a thumbs up in the first photo so it must be safe enough right?
The most important question is whether the kits can be made with grey electrical tape for grey interior cars.
dn010
01-12-2019, 03:03 PM
That looks very scary to me.
The most important question is whether the kits can be made with grey electrical tape for grey interior cars.
Nice pranging, Jon & David P.!
jawn101
01-12-2019, 05:00 PM
Nice pranging, Jon & David P.!
I have no idea what you’re talking about :umm:
AugustneverEnds
01-12-2019, 07:10 PM
https://i.imgur.com/fBTblvY_d.jpg?maxwidth=640&shape=thumb&fidelity=medium
https://i.imgur.com/qtX51ZU_d.jpg?maxwidth=640&shape=thumb&fidelity=medium
https://i.imgur.com/sMjQcK1_d.jpg?maxwidth=640&shape=thumb&fidelity=medium
Late 80s/early 90s BMW steering wheel. Can't tell where the rest of it is from. Too Frankenstein for me
Flash66
01-12-2019, 07:19 PM
LMAO @ this thread
Rhsxo
01-13-2019, 01:24 AM
Hey guys, I just ran across these pics. It looks like someone may have already taken the initiative on this project. The fit and finish... leaves something to be desired... but the branding is on point and I have no doubts at all that the safety of the implementation is top-rate.
Check it out - dual front and even side airbags! Sign me up
https://i.imgur.com/fBTblvY_d.jpg?maxwidth=640&shape=thumb&fidelity=medium
https://i.imgur.com/qtX51ZU_d.jpg?maxwidth=640&shape=thumb&fidelity=medium
https://i.imgur.com/sMjQcK1_d.jpg?maxwidth=640&shape=thumb&fidelity=medium
58997
Bob635
01-17-2019, 07:06 PM
Air bags for Deloreans is something John Delorean was investigating and putting research money into. John worked with Jack Martens, and air bag expert engineer that time. Jack was the engineer who represented Allstate insurance in the early 1970s. He worked with GM to design the Air Cushion Restraint System in the mid 70s full size GM cars. These were great systems. They did not kill any kids. They did not damage your eyes. In fact, GM conducted experiments with piglets to make sure these air bags would not do this.
Jack Made a presentation to the Delorean Midwest connection back around 1995 showing him working with JZD and the test Deloreans. A copy of Jacks slides was supposed to be made by the club, but the slides are MIA. Hopefully, they will find their way back into our hands in the future.
But in regard to your question, these ACRS system were stand alone and could be installed in other vehicles. They were a great design with the drivers air bag 4 times bigger than today. The passenger air bag operated at TWO different pressures depending on the craSH SPEED. IN FACt, these air bags were so safe they did not put shoulder belts into the ACRS cars. GM made over 20,000 of this cars and their extreme safety records were used to force the installation in future cars.
There are 4 components - a bumper sensor, a main computer with decelerometer, the steering wheel and the passenger air bag. They were a $300 option. There is a whole story of politics greed, corruption, etc. that stopped installation further in cars until 1991. Over 30,000 people died needlessly and over 300,000 were injured because of these greedy and corrupt people. But that is another true story.
So could this system be retrofitted to a Delorean? Maybe. The biggest problem is size. They were designed for full size GMs. The GM steering wheel is 2" larger in diameter and the passenger air bag is about 4" two wide.
I have been looking at installing this into the "Iron Man" Delorean. It would require a smaller Steering wheel. That is possible, especially if I am trying to put a steering wheel in with controls on it. The passenger air bag is more problematic because it is 4" too wide. Still thinking about this.
Bob
David T
01-17-2019, 10:39 PM
Do you know why JZD did not use the system? Was it the additional cost, the necessary testing or the liability? Or some combination of the three? Allstate also did a lot of funding and research with Brickin. That was also supposed to be a "safety" car. In fact it's designation was SV-1 (Safety Vehicle-1).
DMC-81
01-18-2019, 04:46 AM
There was a really fascinating article posted earlier this month about the birth of the DeLorean:
Curbside Classics - The Best of 2018 (http://www.curbsideclassic.com/automotive-histories/automotive-history-john-z-delorean-the-bmw-turbo-and-the-curious-coincidence/)
It includes Allstate, the BMW Turbo, and the DSV- DeLorean Safety Vehicle.
http://dmctalk.org/attachment.php?attachmentid=59051&d=1547798908
The DSV- DeLorean Safety Vehicle
http://dmctalk.org/attachment.php?attachmentid=59053&d=1547800811
In the article, there was a photo of JZD and Giorgetto Giugiaro with the first wooden mockup of what would become the DeLorean. Notice the front grill badge says JZD.: :)
http://dmctalk.org/attachment.php?attachmentid=59052&d=1547799139
mr_maxime
01-25-2019, 11:43 AM
I'm OK with no airbags if it means I won't have to live though the heartbreak of crashing my DeLorean.
In all seriousness though, there are several good reasons already pointed out why retrofitting airbags is really cost prohibitive. Airbags are only one component of a complete restraint system that all need to work together to function as intended which need destructive testing to validate.
David T
01-25-2019, 01:04 PM
If it is any consolation, there are few reported deaths associated with the Delorean. Now, because of the limited use of most of them, the probability of death or serious injury is even lower. As proof, look how inexpensive the insurance is.
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.