Log in

View Full Version : Car getting worked on today



About time
05-13-2019, 01:16 PM
Sorry for my absence, the car has been sitting a little as when I took her in for a good going over we found the seals between the eng and trans were leaking rather badly. I ordered a new set of "O" rings and seals from DMC Huston, the car is on the lift as we speak.

On a recent drive I think I notice the clutch seems 'weak", I'm wondering out loud here, how do you know if the clutch is in need of repair without taking things apart? I assume there is a feel that you go by.

Also, assuming the clutch does need to be replaced, any ball park figure on the cost?

Weather here in NJ has been horrid, rain in something like the past 20 out of 22 days, it's crazy.

David T
05-13-2019, 02:11 PM
The main symptom of a worn out clutch is when you are in gear and you step on the gas, the RPM's of the motor go up but you don't move any faster. Not sure what the cost of the parts is now. Figure 5-6 hours labor by someone not experienced on Deloreans. Before assuming a problem with the clutch itself you must make sure the hydraulic system is working right.

Michael
05-13-2019, 02:49 PM
If you are replacing the rear main, and especially if you don't know the history, just replace the clutch and bearing. It's a no brainer.

mr_maxime
05-13-2019, 10:26 PM
If you are replacing the rear main, and especially if you don't know the history, just replace the clutch and bearing. It's a no brainer.

To add to that parts are >$300 and you're not adding any significant labor since the clutch was already removed for the rear main seal.

Drive Stainless
05-13-2019, 11:27 PM
On a recent drive I think I notice the clutch seems 'weak", I'm wondering out loud here, how do you know if the clutch is in need of repair without taking things apart? I assume there is a feel that you go by.



When going up a hill, put the car in a gear that's too high (4th, for example) and push the accelerator pedal to the floor. If the clutch is worn out, the RPMs will increase, but you won't pick up any speed.

mark w
05-14-2019, 11:17 AM
clutch might also feel "weak" if its getting sprayed with oil from a badly leaking RMS.

Mark

About time
05-14-2019, 11:55 AM
I guess it feels weak when it engages, but still feels strong when accelerating or going up hills in a too high of a gear. I'll monitor it and see if it gets a worse feeling. I have no info on when the clutch was last changed if it ever was, the car has less then 55K original miles so it may well be original.

Parzival
05-14-2019, 03:18 PM
I would not have a shop pull my transmission without replacing the clutch. They are already doing most of the work.
It would be like having your AC evaporator replaced, and not replacing the heater core... Ask me how I know.

About time
05-15-2019, 11:46 PM
Turns out I didn't order all the parts that were needed to complete the job, my mechanic ordered what is needed and we're waiting for them to arrive.

About time
05-22-2019, 12:19 AM
Car is back on the road, gave her a good wash and a quick ride, put the cover on her and called it a night. I need to order caliber for the rear drivers side and she should be good to go, it sticks a little now.

David T
05-22-2019, 08:18 PM
If you have a bad/sticking caliper you should consider rebuilding or replacing all of them and the master cylinder. They stick because they get corroded inside.If one is corroded you can assume they all are and each will be sticking as you put more mileage on and the brakes wear.

About time
05-29-2019, 02:22 PM
If you have a bad/sticking caliper you should consider rebuilding or replacing all of them and the master cylinder. They stick because they get corroded inside.If one is corroded you can assume they all are and each will be sticking as you put more mileage on and the brakes wear.
Good advice, something to look into for sure, will consult with my mechanic for best course of action.

About time
05-29-2019, 05:44 PM
Brake calipers are rebuilt items only, also are not currently in stock.

David T
05-29-2019, 10:48 PM
SpecialT has parts to rebuild them (or at least he used to). Check with all of the vendors, if one is out of stock on rebuilt ones, others may have stock. Not a big deal to rebuild the calipers and you can save some money. Usually is not possible to rebuild the master cylinder. If you do buy rebuilts they charge a core if you don't ship the old cores back.

Michael
05-29-2019, 11:04 PM
SpecialT has parts to rebuild them (or at least he used to).

And you can be sure those parts were originally designed for something other than a DeLorean or even Girling.

Ron
05-29-2019, 11:23 PM
Brake calipers are rebuilt items only, also are not currently in stock.Lots of them here:
https://deloreanindustries.com/search.php?search_query=brake%20caliper&section=product

About time
05-30-2019, 08:41 PM
Got a call from DMC Texas today, caliper has been shipped. Thanks all.

opethmike
05-30-2019, 09:28 PM
Lots of them here:
https://deloreanindustries.com/search.php?search_query=brake%20caliper&section=product

May or may not ever actually arrive.

About time
06-03-2019, 10:24 PM
I've got to say, for a car that's 38 years old, she shifts like a dream, smooth as silk, I'm getting more and more impressed with the drivability of this car every day.