Log in

View Full Version : General Odd things found as I learn about 10342



SBL
07-08-2019, 12:12 AM
Today I found a connector that was not connected to anything, at the mid-right firewall, passenger side. I then found what I believe to be what was supposed to plug in it, except it had been spilt/gnarled. See below. The left side (female) has a black wire that connects to a tubular capacitor (I believe), whose other wire disappears into a loom headed towards the driver's side near the firewall. That same left connector has pure red wire that disappears into the loom as well. On the right side (male) there are 2 identical wires connected to the same pin at the bottom of the connector which are black with a blue stripe (it seems green in the pic but it is blue). The top of the connector has a black wire, which connects to the black wire on the female part of the connector. These three all seem to run down the front of the engine and connect to something on the right of the front of engine about 1/2 way down. I cannot see this very well.

I have tried to find these in my diagrams but I am not pulling it together. Based on where the wires went, it is not the few places where I see a BU wire in the wiring diagrams. I did notice that after I made this connection, for the first time I could feel the car shift from 1st to 2nd gear (its an automatic, and I never felt it before, and was wondering if I was starting in 2nd). Anyway, could be a coincidence.

Does anyone know what these wires are for? It would be great to have an annotated view of the front part of the engine that is nearly impossible for us to normally see. Where each wire and hose goes, for manual and automatic. If I ever see one out of a car I will do that.

I have several other oddities (to me) that I will be posting over the next few days which I have found.

Ron
07-08-2019, 12:54 AM
Black/Blue is Vacuum Solenoid #146 & Idle Speed Micro Switch #151. (WS Schematic)
They do go to the Red (capacitor).

titofiedler
07-08-2019, 09:25 PM
I also found the same connector disconnected. Solid black and solid red on one side. On the other side there is a green/white and the other is unknown...


Enviado do meu iPhone usando Tapatalk

SBL
07-08-2019, 10:34 PM
That connector still is somewhat of a mystery to me. Thanks Ron. Just be clear, this is not the capacitor near the middle of the engine, close to the throttle linkage. Rather, it is up against the firewall, running laterally parallel to the wire loom. The black wire from the connector goes to this cap, then a red wire from the cap goes into the loom. A red wire emerges from the loom and connects to the other pin of the connector which flows to the male side with the 2 BU (or is it UB) wires.

It is here (sorry it is turned sideways):

Ron
07-08-2019, 11:47 PM
Black with Blue stripe = B/U = BU
The vacuum solenoid has a (G)reen wire and a BU wire. You can disconnect it and confirm there is continuity from that BU wire to the BU wire at the plug in question (which aligns with the (R)ed wire).

SBL
07-11-2019, 10:42 PM
Yep that was it.

Now to the next :

The thermostat housing looked like a slightly different shape to me than my previous cars. When I took a second look, I noticed that instead of a bleeder there was a solid bolt instead. The size of this bolt is a good bit smaller than stock (which is 10 mm). It turns out to be 5/16" x 20. Not 8 mm, but 5/16th inch bolt threat (not NPT). I cannot find anywhere a nipple or barb with a 5/16 X 20 thread, which I would use for the usual permanent bleeder hose setup. In fact, I really cannot bleed it manually very well as it is.

Does anyone know of a source for a barb/nipple/hose fitting with this thread? I have been through compressor fittings, gas, brake lines, etc, but cannot find 5/16 x 20. And, what do you think this housing is from. I assume some P R or V engine.

SS Spoiler
07-11-2019, 11:14 PM
If the thread is SAE it's probably a hack
job. Could it be rethreaded to a metric size?

FABombjoy
07-12-2019, 10:21 AM
Definitely a PO hack!

It'll probably never be a bleeder again as the tapered seat is likely drilled away. Might best be replaced with a barb using the next size up NPT or something similar, and a hose added in the typical permanent bleeder hose arrangement.

SBL
07-12-2019, 10:30 AM
Probably. I was hoping an expert in threads and hose barbs knew a solution that did not involve resizing. Also could buy a housing from DMCH. I assume on their new housing that the thread sizing is the same as original.

SBL
07-12-2019, 11:41 AM
Note that the 5/16 is SMALLER that the 10 mm stock, so rather than a "hack" on the original part, I think it is a part off of a related engine. Make sense?

Ron
07-12-2019, 12:19 PM
I feel for ya -- Just went through similar for an intake manifold/plenum I did NOT want to remove lol.
You would need to know if the seat is OK and how much meat is left for threads to choose a method.
All of the links I saved below:

Good Seat (Precise drilling is required!):
repair-kit-for-1-4-in-to-7-16-in-or-7mm-to-10mm-screws (https://shop.advanceautoparts.com/p/dorman-help-bleeder-screw-repair-kit-for-1-4-in-to-7-16-in-or-7mm-to-10mm-screws-13915/21260012-p)
repair-kit-for-5-16-in-8mm-and-larger-bleeder-screws (https://shop.advanceautoparts.com/p/dorman-help-bleeder-screw-repair-kit-for-5-16-in-8mm-and-larger-bleeder-screws-13916/17190241-p) (Tap to 1/4 NPT)
(Check seat angles!)

Bad Seat
brake-bleed-valve-kits (https://www.mcfarlaneaviation.com/products/category/brake-bleed-valve-kits/) (Very Expensive)
bleeder-screw-repair-kit (https://www.jpcycles.com/product/240-797/v-twin-manufacturing-brake-caliper-bleeder-screw-repair-kit) - (Tap to SAE 7/16-20 Instructions (https://img.jpcycles.com/staticwebfiles/instructions/pdf/240-797.pdf)) Best bet if you have enough material left, imo.

FABombjoy
07-12-2019, 01:49 PM
Note that the 5/16 is SMALLER that the 10 mm stock, so rather than a "hack" on the original part
Isn't the stock bleed screw BSP? The OD of 1/16 BSP is less than 5/16. I've not seen that referenced as metric before.

I with with "hack" based on the visible 2lbs of goo squished out from the housing on a seal that should be O ring.

SBL
07-12-2019, 09:57 PM
The stock is 10 mm X 1.0 thread.

http://dmctalk.org/archive/index.php/t-16482.html

SBL
07-12-2019, 10:28 PM
NEXT ODDITY:

I am continuing to go through each system. I believe that I found a problem with the vacuum solenoid or WUR.

Using a logic table form Dave of DMC Midwest posted 05-15-2012:

Cold engine at idle should be YES vacuum at warmup regulator T and NO vacuum at distributer vacuum line: my car is YES and NO, as it should be

Warm engine at idle should be NO vacuum at warmup regulator T and NO vacuum at distributer vacuum line: my car is Yes and NO, which is incorrect

Warm engine at 1500 RPM (idle microswitch not engaged) should be NO vacuum at warmup regulator T and YES vacuum at distributer vacuum line: my car is Yes and YES, which is incorrect

So, the WUR seems to be getting vacuum all the time, which is not correct. The distributer vacuum line function seems to be correct. I took a look at the voltage at the connector to the solenoid when unplugged. It is 12v when at idle. It does not go to 0v when off idle, but rather goes to 4-5v. Not sure if that would go to 0v when under load of the coil in the solenoid. Should have tested that.

So, where is the problem?

Ron
07-12-2019, 11:03 PM
Sounds like the thermal control valve is bypassing, IE, feeding the WUR and solenoid all the time.
Check at those two (ie not at the distributor) dead cold and warm to be sure.

Use a test/probe light to see if the voltage to the solenoid (disconnected) comes and goes as expected. (It provides a load needed to test correctly...if the bulb does not glow when off idle, forget the "4-5v".)

SBL
07-13-2019, 06:55 PM
Yep that is is, the thermal control valve is not functional. The vac advance part is working, but not the WUR part. As long as I don't mind (possibly) a more difficult cold start (it is never cold here), could I just feed the solenoid with vacuum and let the idle microswitch control that, and clamp off what is going to the WUR? At least it will not have a tendency to run rich while moving down the road. As I understand it. Not ready to go into the valley.




i

Bitsyncmaster
07-13-2019, 07:31 PM
NEXT ODDITY:

I am continuing to go through each system. I believe that I found a problem with the vacuum solenoid or WUR.

Using a logic table form Dave of DMC Midwest posted 05-15-2012:

Cold engine at idle should be YES vacuum at warmup regulator T and NO vacuum at distributer vacuum line: my car is YES and NO, as it should be

Warm engine at idle should be NO vacuum at warmup regulator T and NO vacuum at distributer vacuum line: my car is Yes and NO, which is incorrect

Warm engine at 1500 RPM (idle microswitch not engaged) should be NO vacuum at warmup regulator T and YES vacuum at distributer vacuum line: my car is Yes and YES, which is incorrect

So, the WUR seems to be getting vacuum all the time, which is not correct. The distributer vacuum line function seems to be correct. I took a look at the voltage at the connector to the solenoid when unplugged. It is 12v when at idle. It does not go to 0v when off idle, but rather goes to 4-5v. Not sure if that would go to 0v when under load of the coil in the solenoid. Should have tested that.

So, where is the problem?

I would think there should be a cold engine at 1500 RPM test which should have vacuum at the WUR and no vacuum at the distributor.

SBL
07-13-2019, 09:06 PM
well it was more like 2000. Clearly not at idle with the microswitch not engaged.

Ron
07-14-2019, 12:19 AM
Yep that is is, the thermal control valve is not functional. The vac advance part is working, but not the WUR part.I'm not sure if you did the first test I suggested and updating or ???
If you mean, "The vac advance part of the system is working,..." I'm with you.
If you mean, "The vac advance part of the thermal control valve is working,..." something is wrong....



As long as I don't mind (possibly) a more difficult cold start (it is never cold here), could I just feed the solenoid with vacuum and let the idle microswitch control that, and clamp off what is going to the WUR? At least it will not have a tendency to run rich while moving down the road. As I understand it. Not ready to go into the valley
The WUR vacuum has virtually no affect WRT starting. The WUR uses the vacuum only to improve acceleration when the engine is cold. (It's other functions are controlled by temperature.)
Connecting it as you suggest will cause it to go lean when you accelerate, if the engine is "cold".

SBL
07-14-2019, 01:39 AM
Ron,

The voltages at the connector are correct when having a load on it, as we suspected. And yes I checked the lines coming right from the thermal control valve dead cold (well about 80 deg F ambient, as "cold" as it gets here) and hot after a cycle of the fans. The line designed to the WUR is always showing vacuum. I also did my best to see if the 3 lines are connected correctly to the thermal control valve, but it is hard to see in there. I remember a post that showed a way to tell, but that probably assumed that the valve was functional.

Agree that when the engine is warmed up, the WUR being without vacuum would not affect acceleration, as I read it.

Ron
07-14-2019, 05:16 AM
Ron,

The voltages at the connector are correct when having a load on it, as we suspected. And yes I checked the lines coming right from the thermal control valve dead cold (well about 80 deg F ambient, as "cold" as it gets here) and hot after a cycle of the fans. The line designed to the WUR is always showing vacuum. I also did my best to see if the 3 lines are connected correctly to the thermal control valve, but it is hard to see in there. I remember a post that showed a way to tell, but that probably assumed that the valve was functional.
Sorry, it is still not clear to me if you checked the line going to the solenoid (not distributor).*
Assuming you did, I'd say it always has vacuum as well. That be the case, the thermal control valve must be bad because, regardless of temp/microswitch, it is impossible to get a yes-yes condition no matter how you route the 3 remaining lines if the thermal control valve is functioning properly.

* It is important because the solenoid can be connected backwards causing it to not vent properly and hold vacuum on the distributor advance line after the solenoid is deactivated...this can fool you into thinking vacuum on the distributor line is there from the vacuum control valve when it is residual/the advance diaphragm supplying it... Not to mention 6 possible ways to route the lines can make ones brain hurt and a 4th line would make it 10 ;-)


Agree that when the engine is warmed up, the WUR being without vacuum would not affect acceleration, as I read it.lol-I'm guessing I wasn't clear... The point there was that, when the engine coolant is below 104F, it will perform poorly and be prone to backfire (too lean) with the vacuum to the WUR blocked off. A bit risky, imho.

SBL
07-15-2019, 10:29 AM
Yes I checked the lines that came directly from the valve, nit at the distributer. From the look at the books, the solenoid lines are not switched. I will need to ponder the problem of being too lean at startup should I take the vacuum off the WUR.

Ron
07-15-2019, 11:41 AM
...I guess, for the time being, you could block it off and baby it until it warmed up a bit while you concentrated on bigger problems.

SBL
07-25-2019, 08:36 PM
ON TO THE NEXT:

While changing the spark plug closest to the firewall on the passenger side, I saw a wire deep in the bowels that goes to a connector that is plugged in to a socket that seems to be screwed into the block. It was hard to see, and I am not sure of the orientation.. Not in the VOD. I took a picture with my fiberoptic camera. I cannot figure out what this is. I believe that it had only one wire coming from it, which had green as a dominant color. Seems like a sensor wire, I cannot trace it. Anyone know what this is?

Ron
07-25-2019, 10:51 PM
If the wire is green with blue stripe, it is the temp gauge sending unit.

SBL
08-20-2019, 09:48 AM
Moving on.....

It looks like I have a non OEM radiator. It is metal, painted black, and has what appears to be a sensor on the driver's side. Can anyone identify the radiator or vendor? There are several Hervey parts that I see on the car, so that is a possibility.

SBL
08-20-2019, 10:22 AM
Correction: sensor is on passenger side

SBL
08-28-2019, 01:18 AM
Nobody recognizes that radiator? I wonder if it was done with whatever could be found that fit.

David T
08-28-2019, 10:17 AM
It is possible it was built up by a local radiator shop and not supplied by any of the Delorean vendors.

Ron
08-28-2019, 12:39 PM
The sensor (or fan switch?) in the tank has a much larger diameter compared to those I've seen. The electrical socket is another clue. You might have better luck showing the pic to someone at the parts store.

SBL
01-28-2020, 02:45 AM
Most of the "mysteries" that I found with my car were due to changes in the wiring colors during production, my inability to see the wiring colors due to location or lack of lighting, and the installation of newer parts (which were well deserved) where I did not have the documentation. When all is set set and done, I conclude that my car was well maintained and is mostly original with the appropriate upgrades and replacements for a car of its age, and is behaving as per original specs if not better.

Nevertheless, the obsessive compulsive nature that I have (most DeLorean owners have this affliction) will show itself from time to time and end up as posts here. Thanks to everyone for answering my questions.