View Full Version : New Owner Check this out
Giamanut
09-26-2019, 11:40 PM
So I just bought 5051 built in OCT 81 it has been in a garage since 1998 it has 29k miles!
Body and interior are perfect engine is not frozen and is very clean.
Struts are still black and look like new.
Tires looked fine and were not even flat! Just low on air.
I will do one of two things!
1) Replace all Master cylinders and clutch slave
Rebuild all calipers
Replace Fuel Pump accumulator and clean all injectors and Overhaul WUR!
Replace cooling system.
Repair AC as required.
and put it out there for sale at the higher end of the scale.
Or sell it without doing all that.
I won't run the fuel pump with out going through the fuel system.
But I have no doubt the car will run very well!
What would you do?61288612896129061291
Michael
09-26-2019, 11:45 PM
So you are going to do one of two things; put time and money into it and sell it or do nothing to it and sell it cheaper.
Well the struts are black and new so there's that.
Giamanut
09-26-2019, 11:58 PM
Yes the struts are black and original the point was the car looks very nice for being driven into a garage and parked in 1998. The fact that the paint under the car has not gone to trash is .... well good.
Also just wondering what seasoned owners might do. So I thought a few details might be good.
jackb
09-27-2019, 12:18 AM
A seasoned owner tends to care about the car, not flipping it like any other.
Perhaps you'll find people more eager to give you advice in a place that focuses on buying/selling cars, more than you would on an owners/enthusiasts forum that has a big focus on maintaining the car.
Work on it and sell it, or don't and sell it. Either way you've decided what you're going to do in the end.
With the way you're talking about it, I don;t know if I'd call you an owner, as much as I would call you a temporary possessor until it goes to an owner.
dmcnc
09-27-2019, 07:22 AM
Rather than shot-gun blasting through all the things that might be wrong, I would recommend getting it inspected my a vendor or an experienced owner and prioritize safety and minimum running requirement items first. Where are you located?
Giamanut
09-27-2019, 08:22 AM
Rather than shot-gun blasting through all the things that might be wrong, I would recommend getting it inspected my a vendor or an experienced owner and prioritize safety and minimum running requirement items first. Where are you located?
Eastern Wa.
I probably should note I've been a mechanic for around 31 years, I would love to keep this car, but I believe it would be in better hands with a collector. I would pretty much have to daily driver this and sell my Vette.
I don't want it butched up in anyway as it is pretty exceptional as is.
Just kind of wondering what would do the car more justice!
I get the whole pride of ownership, and yes I am not going to own it for long, however I dam sure want to enjoy it for the time I do own it.
Giamanut
09-27-2019, 08:40 AM
A seasoned owner tends to care about the car, not flipping it like any other.
Perhaps you'll find people more eager to give you advice in a place that focuses on buying/selling cars, more than you would on an owners/enthusiasts forum that has a big focus on maintaining the car.
Work on it and sell it, or don't and sell it. Either way you've decided what you're going to do in the end.
With the way you're talking about it, I don;t know if I'd call you an owner, as much as I would call you a temporary possessor until it goes to an owner.
Well, just trying to do the car justice as I know I can not keep it. The fact that I am seeking some advice about how to handle this should make it obvious that I do care about the car.
I just can't permanently own it at this time. So yes I believe it needs to be in someones collection. I can not afford to be a collector at this time.
I do find it odd that you suggest a car flipping site for information or advice, I assumed that talking to people that love this Icon might be a better way to go.
Just because I can't own it for long, does not mean I can't love it while I have it!
I feel like I have been entrusted with it.
iflights
09-27-2019, 02:14 PM
I won't run the fuel pump with out going through the fuel system.
But I have no doubt the car will run very well!
Tough to get a price at the higher end since it's technically a non-runner.
Nicholas R
09-27-2019, 02:32 PM
Honestly I think you should sell it now.
I understand you're a mechanic, but if you're trying to "do the car justice," you should leave the repairs and restoration to someone that has an interest in the car more than flipping it. Otherwise you risk doing more harm than good in an attempt to maximize profit.
Michael
09-27-2019, 05:01 PM
61296
Giamanut
09-27-2019, 09:57 PM
Honestly I think you should sell it now.
I understand you're a mechanic, but if you're trying to "do the car justice," you should leave the repairs and restoration to someone that has an interest in the car more than flipping it. Otherwise you risk doing more harm than good in an attempt to maximize profit.
Thank you, that is a valid honest opinion. A good one too.
Giamanut
09-27-2019, 10:01 PM
Tough to get a price at the higher end since it's technically a non-runner.
Yes I would not expect a higher price unless the car was right.
Giamanut
09-27-2019, 10:06 PM
61296
Thanks for the great advice. That should make something feel good.
DMC-81
09-27-2019, 11:32 PM
So I just bought 5051 built in OCT 81 it has been in a garage since 1998 it has 29k miles!
Body and interior are perfect engine is not frozen and is very clean.
Struts are still black and look like new.
Tires looked fine and were not even flat! Just low on air.
I will do one of two things!
1) Replace all Master cylinders and clutch slave
Rebuild all calipers
Replace Fuel Pump accumulator and clean all injectors and Overhaul WUR!
Replace cooling system.
Repair AC as required.
and put it out there for sale at the higher end of the scale.
Or sell it without doing all that.
I won't run the fuel pump with out going through the fuel system.
But I have no doubt the car will run very well!
What would you do?61288612896129061291
What would I do? I would keep it and take my time restoring it right....It looks like you've got a nice example there. A lot of enthusiasts are trying to find one like that... even the Oct 81 production month is desirable. Then I would sell the Vette if I needed to. I've owned 2 Corvettes, and to me, Delorean ownership is much more satisfying. For example, just the other day, I was in traffic and a driver caught a glimpse of the DeLorean pulling up alongside, and he stuck his head out of his car window and while looking incredulous, mouthed "HOLY SH*T!!! "
You just don't get that kind of reaction from driving a Vette. On Autotrader today, there are 3,441 Corvettes for sale while there are 0 DeLoreans.
But, that's only my opinion. However, if you're not enthusiastic about the car, I agree with Nick, don't touch it and sell it as is. You'll only risk making things worse for the next owner.
Good luck to you.
I was in the exact same position as you a decade ago and, although I mostly agree with Dana, I have to say go for it!
I don't see the concern about you making things worse for the next owner -- Being a seasoned mechanic, you know half of the game is knowing what NOT to do. Seems obvious that you are doing your homework and have already identified the #1 thing. Not to mention you are here... To figure out what TO do boils down to one thing, K-Jet and your willingness to learn it. If you clean it up thoroughly, we can walk you through the rest.
Then comes the real decision(s) -- Will you become to love it, or hate it? If the former, how to keep it?
Short and sweet- Change out all of the fluids, disconnect the pump and get it running good enough to prove the engine and that the trans takes gear. I assume you know how to do that and will know how to proceed from there... :)
Giamanut
09-28-2019, 05:28 PM
I was in the exact same position as you a decade ago and, although I mostly agree with Dana, I have to say go for it!
I don't see the concern about you making things worse for the next owner -- Being a seasoned mechanic, you know half of the game is knowing what NOT to do. Seems obvious that you are doing your homework and have already identified the #1 thing. Not to mention you are here... To figure out what TO do boils down to one thing, K-Jet and your willingness to learn it. If you clean it up thoroughly, we can walk you through the rest.
Then comes the real decision(s) -- Will you become to love it, or hate it? If the former, how to keep it?
Short and sweet- Change out all of the fluids, disconnect the pump and get it running good enough to prove the engine and that the trans takes gear. I assume you know how to do that and will know how to proceed from there... :)
I do have a good Idea how to not make things worse, I won't even run the fuel pump until the system (Tank to Injectors) is clean and new filters installed. I have clean hundreds of CIS injectors so no problems there. and have overhauled plenty of calipers the rest is pretty basic except the K-JET, but that has been used on so many cars there is a lot of info. So yes I am not afraid and just because I may not get to keep it, it is still pretty dam cool just to work on it.
No mods have been done to this car that i know of, still has the plastic coolant res. I really don't want to mod or change a thing.
Giamanut
09-28-2019, 05:33 PM
613056130461303
Just a few more pictures!
I do have a good Idea how to not make things worse, I won't even run the fuel pump until the system (Tank to Injectors) is clean and new filters installed. I have clean hundreds of CIS injectors so no problems there. and have overhauled plenty of calipers the rest is pretty basic except the K-JET, but that has been used on so many cars there is a lot of info. So yes I am not afraid and just because I may not get to keep it, it is still pretty dam cool just to work on it.
No mods have been done to this car that i know of, still has the plastic coolant res. I really don't want to mod or change a thing.
Visit the sites Resource Section (http://dmctalk.org/forumdisplay.php?5-Resources) and download the searchable Workshop Manual (http://dmctalk.org/showthread.php?2866-Searchable-Workshop-Technical-Bulletins-and-Volvo-Engine-Manuals) if you haven't already.
Giamanut
09-28-2019, 08:17 PM
Visit the sites resource section Resource Section (http://dmctalk.org/forumdisplay.php?5-Resources) and download the searchable Workshop Manual (http://dmctalk.org/showthread.php?2866-Searchable-Workshop-Technical-Bulletins-and-Volvo-Engine-Manuals) if you haven't already.
Got one with the car! And a parts book! I have been reading for about a couple of weeks.
ssdelorean
09-30-2019, 06:30 PM
No mods have been done to this car that i know of, still has the plastic coolant res. I really don't want to mod or change a thing.
That plastic coolant res is good for at least 226k miles. My car can vouch for that!
Hill Valley PD
10-01-2019, 09:30 AM
That car looks really clean and original. Looks like someone removed the throttle body recall/de-ice recall kit (metal guard to keep it dry to prevent freezing in cold weather). In terms of modifications, I would replace the plastic header bottle with a stainless steel one as well as the nearly 40 year old rubber fuel lines with stainless steel ones. Change all fluids, brakes probably need to be all redone, your fuel system is probably in trouble, maybe a 30K major service kit, and that's just the beginning. The rule of thumb if having a vendor do the work to get a non-running DeLorean in good running order is about 1K per year that the car sat. I think these numbers are inflated, but it is not hard for the bills to add up, especially once you get it running, and other things start to manifest themselves. Good luck with your decision. If you do decide to bring it back to life, this community is probably one of the best in the collector car arena. The vendor support is also second to none.
Giamanut
10-03-2019, 09:01 AM
Hi just an update.
I finish the brakes and changed the clutch master cylinder as well as the fuel pump and sending unit. The tank was pretty dirty.
Next up accumulator and fuel filter, clean injectors and replace injector seals. Then I can put some fuel in it!
I have some electrical issues but I will start by cleaning a lot of grounds and connections. I expect to get my first start in about a week as work does get in the way!
Giamanut
10-03-2019, 09:04 AM
That car looks really clean and original. Looks like someone removed the throttle body recall/de-ice recall kit (metal guard to keep it dry to prevent freezing in cold weather). In terms of modifications, I would replace the plastic header bottle with a stainless steel one as well as the nearly 40 year old rubber fuel lines with stainless steel ones. Change all fluids, brakes probably need to be all redone, your fuel system is probably in trouble, maybe a 30K major service kit, and that's just the beginning. The rule of thumb if having a vendor do the work to get a non-running DeLorean in good running order is about 1K per year that the car sat. I think these numbers are inflated, but it is not hard for the bills to add up, especially once you get it running, and other things start to manifest themselves. Good luck with your decision. If you do decide to bring it back to life, this community is probably one of the best in the collector car arena. The vendor support is also second to none.
Yes but that would amount to a 21k bill so not gonna happen. I will do as much as possible with the help I get here I am currently moving right along. Thanks for the reply!
Hill Valley PD
10-03-2019, 09:32 AM
Yes but that would amount to a 21k bill so not gonna happen. I will do as much as possible with the help I get here I am currently moving right along. Thanks for the reply!
It sounds like you know what you are doing, so you will save a ton of money. You have decided to bring it to life after all? Awesome! I would definitely change out and/or clean the fuses and relays. Electrical box is located under the parcel shelf behind passenger seat. You will have to manipulate the plywood piece that is behind the seats by tugging it toward the front of the car while pulling the shelf upward. Took me a while to figure it out. You can purchase all new fuses and relays from the vendors. It's a couple hundred dollars but probably worth it since who knows the last time any of that was done.
New Owner Recommendations from DMC MW (a bit overkill on times but nothing hard or expensive):
Use a battery maintainer if car is going to sit longer than a few weeks, not a trickle charger.
Engine oil is Castrol GT 20W50, 7 quarts, every 3K or 12 months. Once a year - do in Fall before Winter storage.
Coolant is Prestone Universal Green mixed 50-50. Coolant flush takes two gallons, i.e. 4 gallons mixed. Change every 2 years.
Automatic trans. fluid is Dextron III, 4 quarts
Trans. oil is 75W90
Change every 5 years. 4 quarts
Brake and clutch fluid is Catrol GT LMA DOT 4
Change every 2 years
Tire pressure is 24 front, 30 rear
Clean/replace fuses every 2 years
Michael
10-03-2019, 10:07 PM
Yes but that would amount to a 21k bill so not gonna happen. I will do as much as possible with the help I get here I am currently moving right along. Thanks for the reply!
If the car was stored correctly, you can get it running far easier. I agree the 1k a year is inflated and based on a vendor doing all the work as well as supplying parts. If you know what you are doing, I bet you could get the car running and driving fairly easily but the coming months of "shake down" cruises will no doubt shed light on more issues to be addressed before you consider it a top tier car.
Giamanut
10-04-2019, 08:14 AM
If the car was stored correctly, you can get it running far easier. I agree the 1k a year is inflated and based on a vendor doing all the work as well as supplying parts. If you know what you are doing, I bet you could get the car running and driving fairly easily but the coming months of "shake down" cruises will no doubt shed light on more issues to be addressed before you consider it a top tier car.
Thank you and I totally agree with that, I am finding Items as I go but the lack of corrosion and general condition is remarkable considering how long it sat.
The electrical seems to have suffered somewhat, chasing down and cleaning all the ground wire are on my list.
I know there are mods out there for fans headlight etc but I wonder if I should do them or just keep it totally original problems and all? Any thoughts on that?
It would be hard to keep the radiator original as I think it will need to go away.
Hill Valley PD
10-04-2019, 09:29 AM
Yes, that is a vendor quote about 1K per year of sitting provided they do/provide EVERYTHING at $125/hour labor.
In terms of mods, my car came with the Eibach Springs/Spax Shocks. This was sold as a suspension upgrade kit from DMC Texas and lowers the car to its intended height, while improving ride and handling. Many vendors (DeLoreanGo, DPI, DMC etc.) sell suspension upgrade kits, and I recommend them since it improves the look of the car a lot (no more high front end/huge wheel to fender gap). My other deviations from stock are CD player (wish I had original Craig), stainless steel clutch/fuel lines, as well as exterior and interior LEDs (minus gauge cluster and headlights). The reason I did the latter is I wanted to leave the doors open at car shows and not drain the battery, and my taillight boards were finicky, so I replaced them. It was sort of, "Well, if I do this, then I should do that." I have not done LEDs in the gauges (did AC panel) because I am not confident enough to take the dash apart. I also did not do the headlights because I haven't found any I really like that don't look cheesy. It depends if you want to keep the car as original as possible. Bear in mind, there have been aftermarket improvements to many things originally on the car that improve reliability and drivability, so it depends what you are after. If going completely stock, your JVC tape deck would not have come in there. All '81s used Craigs, and ASI on later '82's and all 83's.
Giamanut
10-04-2019, 10:22 PM
Yes, that is a vendor quote about 1K per year of sitting provided they do/provide EVERYTHING at $125/hour labor.
In terms of mods, my car came with the Eibach Springs/Spax Shocks. This was sold as a suspension upgrade kit from DMC Texas and lowers the car to its intended height, while improving ride and handling. Many vendors (DeLoreanGo, DPI, DMC etc.) sell suspension upgrade kits, and I recommend them since it improves the look of the car a lot (no more high front end/huge wheel to fender gap). My other deviations from stock are CD player (wish I had original Craig), stainless steel clutch/fuel lines, as well as exterior and interior LEDs (minus gauge cluster and headlights). The reason I did the latter is I wanted to leave the doors open at car shows and not drain the battery, and my taillight boards were finicky, so I replaced them. It was sort of, "Well, if I do this, then I should do that." I have not done LEDs in the gauges (did AC panel) because I am not confident enough to take the dash apart. I also did not do the headlights because I haven't found any I really like that don't look cheesy. It depends if you want to keep the car as original as possible. Bear in mind, there have been aftermarket improvements to many things originally on the car that improve reliability and drivability, so it depends what you are after. If going completely stock, your JVC tape deck would not have come in there. All '81s used Craigs, and ASI on later '82's and all 83's.
Yeah I caught that JVC also but didn't know if it was some kind of up sell from DeLorean. Thanks
As far as LED and lowering goes well I wish the whole car was euro spec but we will see.
Giamanut
10-04-2019, 10:33 PM
So I get a whole day and a half to work on the D this weekend! Whooo Hoooo !
My to do list is not to bad.
Going to put some fuel in the tank and disconnect the fuel filter/flush lines to that point.
R and R the accumulator and install new fuel filter.
Flush the system up to the fuel dis then start checking the return lines
Button up the fuel system up to the injectors.
Remove the injectors for cleaning, and test for even fuel flow from fuel dis.
Clean all the ground I can find!
Remove the spark plugs and oil the cylinders.
Crank the Engine!!!!!!!!
Then after lunch!:hmm:
Then after lunch!:hmm:
Hopefully... :burnout:
Giamanut
10-09-2019, 12:45 AM
Just got to a point I could try to start it.
2 cranks it fired!
It runs it run it runs Whooooo hooooooo.
It will start and idle at this point rough but it's stays alive! will not rev just falls on it's face. but now I can open the check book.
Next up new Radiator, Fans, Ignition switch, Water pump,Thermostat, Plug wires. a couple more grounds to clean a few connectors and a little more work on the fuel system.
I don't think this car has ever seen rain, Just awesome!
Hill Valley PD
10-12-2019, 09:37 AM
Is it growing on you? Keeping it? That car looks incredibly clean and is probably a keeper.
Giamanut
10-12-2019, 09:41 PM
Is it growing on you? Keeping it? That car looks incredibly clean and is probably a keeper.
Yes it is growing on me but I don't know......... It is surprisingly clean
I have major tuneup and pressure gauge on the way so that is next. Then I need to get the heater blower, mirrors and ac working Oh and one running light in the back.
and adjust the parking brake!
So with my schedule about 3 more weeks!
carbob81
10-14-2019, 12:21 AM
....
I just can't permanently own it at this time. So yes I believe it needs to be in someones collection.
At what point did these become collector cars? So many still on the road and not a limited production.
We all love them for the look, feel and mine but ....
The body style was very nice , the rest of the design and production was not so well executed.
Very many mistakes and warts but I do love the car.
How to puck up a very good idea is a capital lesson here.
It was on line to be a king at the time but design and production staff failed in spades.
Bob
louielouie2000
10-14-2019, 09:46 AM
At what point did these become collector cars? So many still on the road and not a limited production.
We all love them for the look, feel and mine but ....
The body style was very nice , the rest of the design and production was not so well executed.
Very many mistakes and warts but I do love the car.
How to puck up a very good idea is a capital lesson here.
It was on line to be a king at the time but design and production staff failed in spades.
Bob
Large scale car collectors have had DeLoreans in their collections since these cars were new. They aren't exactly Camrys and they aren't making any more of them...
Having owned 2 of these cars & been in the community 20 years, I'm keenly aware of the DeLorean's shortcomings. But honestly, it's amazing they weren't far, far worse. The company had 28 months to design & build a car from scratch (or the new UK government was going to pull the plug), concurrently design & build a factory for a car that wasn't yet fully fleshed out (and the factory site was literally in the middle a worn-torn area), hire & train a totally unskilled workforce (which must be equally divided between factions that were actively killing each other), all with a brand new company which had limited funds & zero experience building cars. Let's not forget the DeLorean wasn't exactly an easy car to build, either- they had to design & productionize stainless steel body panels (nobody has done that before or since), design & productionize gull-wing doors (the torsion bars ended up having to be designed by Grumman aerospace utilizing liquid nitrogen... Grumman also is known for the B-2 Spirit bomber & F-14 Tomcat), build a fiberglass body to fit under that problematic stainless steel body, all of this without computer aided design. 40 years later, even legacy automakers that have been around a century & have billions of dollars at their disposal couldn't pull off concurrently designing & building a new car & factory in 2 years the way DMC did. Let's not forget all cars of the late 70s/early 80s are all pretty much garbage when it comes to quality, too. Yes, the DeLorean is lacking in many ways... but what's remarkable is how much worse it truly could have been.
Hill Valley PD
10-14-2019, 10:28 AM
Large scale car collectors have had DeLoreans in their collections since these cars were new. They aren't exactly Camrys and they aren't making any more of them...
Having owned 2 of these cars & been in the community 20 years, I'm keenly aware of the DeLorean's shortcomings. But honestly, it's amazing they weren't far, far worse. The company had 28 months to design & build a car from scratch (or the new UK government was going to pull the plug), concurrently design & build a factory for a car that wasn't yet fully fleshed out (and the factory site was literally in the middle a worn-torn area), hire & train a totally unskilled workforce (which must be equally divided between factions that were actively killing each other), all with a brand new company which had limited funds & zero experience building cars. Let's not forget the DeLorean wasn't exactly an easy car to build, either- they had to design & productionize stainless steel body panels (nobody has done that before or since), design & productionize gull-wing doors (the torsion bars ended up having to be designed by Grumman aerospace utilizing liquid nitrogen... Grumman also is known for the B-2 Spirit bomber & F-14 Tomcat), build a fiberglass body to fit under that problematic stainless steel body, all of this without computer aided design. 40 years later, even legacy automakers that have been around a century & have billions of dollars at their disposal couldn't pull off concurrently designing & building a new car & factory in 2 years the way DMC did. Let's not forget all cars of the late 70s/early 80s are all pretty much garbage when it comes to quality, too. Yes, the DeLorean is lacking in many ways... but what's remarkable is how much worse it truly could have been.
Well said. Given the late 70s and early 80s and what else was being produced, the DeLorean has actually aged pretty well in terms of build quality and performance relative to its time. Look at the crap GM was putting out then. Is the DeLorean a great car? No, but it's not a bad car either. It is the perfect embodiment of the era, style over substance. Furthermore, everyone involved in the production from start to finish did an amazing, never to be repeated again, job with the factory/car in record time. Even Porsche told them it would take 5 years, which is why they contracted Lotus to engineer the car for production. They did it in less than half the time Porsche quoted. The company's failure, if you had to place blame in one place, lies with the man himself who sold the idea to the British government of a company that could reliably sell 30K cars per year, which was about 5x what was actually realistic. Had they set out to produce around 6K cars a year and then added more models, they'd still be around. Obviously, a lot of factors contributed to its demise, but that is the one that sticks out to me the most. The production goals were just too high for a 25K underpowered sports car in the recession of the early 80s.
Giamanut
10-15-2019, 01:14 AM
So I got a little further on the car today, Installed new injectors cap rotor an wires. Adjusted the parking brake, Trouble shot the Freq valve to Wrong relay installed. The car also had the wrong accumulator.
Started looking into why the Blower Motor does not work, Dropped it out and it test good so on to the switch or relays maybe.
Oh yeah installed my new ignition switch today.
Tomorrow I will get a new angle drive kit.
A radiator and fans.
The stock fans work and the car does not leak but it is gonna be better to have the new fans the stocks sound way loud!
Oh and I have a new water pump but the original is working fine so! maybe I will wait on that.
Also got the fuel filter finished today!
I have a test gauge for the fuel system coming along with a Vacuum hose kit so I hope to be totally on the road by 10/23/19.
Giamanut
10-17-2019, 12:28 AM
I was in the exact same position as you a decade ago and, although I mostly agree with Dana, I have to say go for it!
I don't see the concern about you making things worse for the next owner -- Being a seasoned mechanic, you know half of the game is knowing what NOT to do. Seems obvious that you are doing your homework and have already identified the #1 thing. Not to mention you are here... To figure out what TO do boils down to one thing, K-Jet and your willingness to learn it. If you clean it up thoroughly, we can walk you through the rest.
Then comes the real decision(s) -- Will you become to love it, or hate it? If the former, how to keep it?
Short and sweet- Change out all of the fluids, disconnect the pump and get it running good enough to prove the engine and that the trans takes gear. I assume you know how to do that and will know how to proceed from there... :)
I found a crossover relay in the Lambda relay spot FV won't work like that. Also someone installed the wrong accumulator! I have ran and drove it around a nearby parking lot. Really surprised the mirrors and windows work.
I finished the Fuel system and am waiting on the correct Lambda relay the heater blower motor works bench check but not in the car.
completed the brake and clutch system
Replaced the Bonnet and trunk struts adjusted the E brake
Have a new angle drive kit for this friday.
Fuel pressure test gauges on the way
New heater switch and mode switch rebuild kit also in route
Installed new cap rotor and wires and injectors and have spark plugs for Friday!
Will reset Co? Injectors and start car again Friday and fine tune Monday Tues and Wens! next week!
That is a running driving car at that point.
Final touches will be charge A/C and roof box kit/ repair! Then it will be as nice as any I have seen! Just seen one on Ebay sell for 33K and it was not near as nice as mine! I am Jacked just hope I own it for a little bit after it is done!
Giamanut
10-18-2019, 05:11 PM
Well need some head gaskets now? I thought that might come into play.
So far I have cleaned the tank replaced the fuel system except the FD and WUR which work great.
the angle drive
tail light boards because I felt like it
one head light.
Rotor cap wires and plugs.
Brake and clutch master
Overhauled calipers fix and adjusted Parking brake
Got the mirrors and windows working
verified Cabin fan works
Replaced the starter
Trouble shot FV inop to Lambda relay ( cross over valve where the Lambda Relay should be).
Left to do !!!!
change Water pump Radiator and hoses
Roof box repair
Mode sw
heater fan sw
head gaskets
Fluids!
Set Fuel pressure and CO.
2 more weeks!!! With my work schedule!
I got a ton of info from this site
Thanks much!
sdg3205
10-19-2019, 03:33 AM
Well need some head gaskets now?
How did you come to realize you need new head gaskets?
Giamanut
10-19-2019, 07:02 AM
How did you come to realize you need new head gaskets?
White smoke! Pulsed pressure in the coolant tank and number 2 spark plug soaking wet.
Michael
10-19-2019, 09:50 AM
Well being in the condition it's in, it's a good time to do the water pump and all the VOD coolant and vacuum hoses and other replaceable items like cap, rotor, wires, etc.
sdg3205
10-19-2019, 11:47 AM
White smoke! Pulsed pressure in the coolant tank and number 2 spark plug soaking wet.
Fair enough. Careful with them liners.
Parzival
10-19-2019, 11:55 AM
Im in the middle of doing my head gaskets... and liner seals. I'm doing the liner seals with the engine in the car by lifting the engine a bit and dropping the pan.
You can do the head gaskets with out disturbing the liner seals, I was carful when removing the heads not to disturb them, but I still don't trust them at this age. I've also spoken to a number of the venders this week, and heard that cars coming in with leaking liner seals is starting to be more common. I'm not risking doing this twice.
When going in this deep, there is always the possibility of going in even deeper once you get in there!
Also as someone else has mentioned, change the water pump.
Giamanut
10-19-2019, 10:25 PM
Well being in the condition it's in, it's a good time to do the water pump and all the VOD coolant and vacuum hoses and other replaceable items like cap, rotor, wires, etc.
Yep did the Cap rotor plugs Water pump is on back order for a week but paid for and on its way Vac lines should be here Monday along with complete coolant hose kit Radiator and fans are here waiting for Monday ( I have Monday Tues and Wednesday off)
I will be very careful pulling this head.
Also have some pressure regulator O rings and adjustment washers coming!
Not going to pull the head until Parts are here.
Thank for the replies.
Should I post some pictures?
Giamanut
10-19-2019, 10:27 PM
Fair enough. Careful with them liners.
I will. I understand you don't want to rotate the engine or pull the head straight up when removing. Makes sense to me.
Giamanut
10-19-2019, 10:31 PM
Im in the middle of doing my head gaskets... and liner seals. I'm doing the liner seals with the engine in the car by lifting the engine a bit and dropping the pan.
You can do the head gaskets with out disturbing the liner seals, I was carful when removing the heads not to disturb them, but I still don't trust them at this age. I've also spoken to a number of the venders this week, and heard that cars coming in with leaking liner seals is starting to be more common. I'm not risking doing this twice.
When going in this deep, there is always the possibility of going in even deeper once you get in there!
Also as someone else has mentioned, change the water pump.
I thought about that some but I think since the combustion is near the upper end of the cylinder the lower seal might not get the beating the head gasket does. Unless the cylinder is worn then .... ???? I guess I will find out when I get there!
Parzival
10-20-2019, 01:09 AM
I thought about that some but I think since the combustion is near the upper end of the cylinder the lower seal might not get the beating the head gasket does. Unless the cylinder is worn then .... ???? I guess I will find out when I get there!
My pistons are in great shape, and the car only has 27k miles. My compression test gave me 170psi at every cylinder. My head gasket leak was so minimal that it took me 2 months to confirm it. I could have likely driven it like that for thousands more miles, but sadly my OCD will not allow me to live with a problem. I could hardly detect combustion gasses in the cooling system, and pressurizing the cooling system for about 15 minutes would only reveal a drip of coolant in the same cylinder as you, (number 2)
The issue is that the paper liner seals are very old, and while it is possible to pull the heads without disturbing them, once the heads are off there is no good way to know for sure that they are still sealed! you can try to gently rock them back and forth to make sure they dont move and are stuck down, but you may cause them to move in doing so. At this point in the game, I just don't want to trust the old seals, especially since their failure will results in a dumping of the coolant into the crank case. If that happens and you don't notice it right away... well, you may be on the lookout for a replacement engine.
Giamanut
10-20-2019, 08:04 AM
My pistons are in great shape, and the car only has 27k miles. My compression test gave me 170psi at every cylinder. My head gasket leak was so minimal that it took me 2 months to confirm it. I could have likely driven it like that for thousands more miles, but sadly my OCD will not allow me to live with a problem. I could hardly detect combustion gasses in the cooling system, and pressurizing the cooling system for about 15 minutes would only reveal a drip of coolant in the same cylinder as you, (number 2)
The issue is that the paper liner seals are very old, and while it is possible to pull the heads without disturbing them, once the heads are off there is no good way to know for sure that they are still sealed! you can try to gently rock them back and forth to make sure they dont move and are stuck down, but you may cause them to move in doing so. At this point in the game, I just don't want to trust the old seals, especially since their failure will results in a dumping of the coolant into the crank case. If that happens and you don't notice it right away... well, you may be on the lookout for a replacement engine.
Same cylinder #2. that is odd. Yeah mine is actually not a giant leak either. I think what happened is after I got it started it ran rough and possible was not firing on #2 when I put in the new injectors rotor cap a plugs i fired and was really smooth, but it had a lot more pressure in that # 2 so it found the weak spot! It barely smokes at all once it runs for a few minutes.
Giamanut
10-23-2019, 12:59 AM
Bit of an update.
Got my new Radiator and fans installed.
totally fixed my bower motor situation, that was crazy. spent a few hrs trying to figure out what was up with one fan relay socket. Finally just pulled the sockets out discovered they were not in the correct spot! Found the problem in the fuse box wire behind #10 fuse.
Ran a Fuel pressure test just for fun after installing new O rings in the main Pressure Regulator. So Engine off and fuel pump jumper I got about 28 psi control and 80 main at 40 degrees ambient.
Not sure if that is good? Will check with engine running after I get the head gaskets done.
Discovered the hidden antenna. and the relay near the ECU. But it looks let it was never hooked up.
Finished the roof box repair. Way easier than expected, torque rods were way to tight. Door are perfect now.
Almost ready to close the fuse relay area, just need to fix the windshield washer pump.
Correct lambda relay fix the FV so that's done. Installed Led tail lights and flasher and my interior Blinker light died. Wonder if I should install Leds there also and in the front of the car maybe.
Left to do
Head gaskets / Vacuum line rubber coolant lines.
washer motor and wiper cover/cap.
charge AC
Fine tune..CO and fuel pressures.
Everything else is now working properly.
Take PICTURES
Michael
01-25-2020, 01:06 PM
OK I just re read this thread after someone linked to it in another post. You really did right by that car. Of all the cars for sale right now this should be at the top of anyone's prospect list.
I seriously think you could get a lot more $$(at the very least expedite the sale process) if you spent an afternoon cleaning the frame and undercarriage.
Riley88
01-25-2020, 05:15 PM
Eastern Wa.
I probably should note I've been a mechanic for around 31 years, I would love to keep this car, but I believe it would be in better hands with a collector. I would pretty much have to daily driver this and sell my Vette.
I don't want it butched up in anyway as it is pretty exceptional as is.
Just kind of wondering what would do the car more justice!
I get the whole pride of ownership, and yes I am not going to own it for long, however I dam sure want to enjoy it for the time I do own it.
I would add cleaning the fuel tank and new filter to that list bud if you havent
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.