Log in

View Full Version : front console cover flare



SBL
08-10-2020, 12:14 AM
Near the front of the car, at shin level, my console cover has flared on both sides. Just at the "wing" area. See picture. This happened when the previous owner took the car to a stereo shop and they kept pulling back on this part to get their hands up behind the radio/console dash.

I have been thinking of putting a screw into it into the hump (using one of those grey plastic snap on covers to cover the head), pulling it in towards the hump. I could also peel back the vinyl at the corner and put the screw in and tighten it up to about 1/2 inch of the carpet then fold the vinyl back and glue it to the board.

Is there anything inside the hump that I could damage by drilling a small hole?

In its current state is is not ugly per se, it just bugs me. I have attempted to coax it back from its warped shape to no avail.

Other suggestions welcome.

64255

Bitsyncmaster
08-10-2020, 07:18 AM
I remember doing that many years ago. Just don't let your drill go to far after it penetrates the tub.

CFI
08-10-2020, 09:18 AM
It’s a common problem. Whatever backing material was originally used ends up warping over time. I recently read that someone used picture hanging hooks to pull the flared parts in. You could also try powerful magnets, although attaching one to the back of the console material may prove difficult. I’ve considered pulling the console out and reinforcing that area with a thin piece of metal to straighten it and prevent it from warping again. I’ll probably just do what you mentioned and screw it down.

louielouie2000
08-10-2020, 09:52 AM
If the warped console flare bothers you now, seeing a screw (even if it has one of those covers) will make you crazy too. Invariably the color & texture won't match the vinyl, and it will cause the vinyl to dimple around the screw/cover.

I'd figure out something invisible. Perhaps affix some high-strength Velcro to the back of the console cover, and then figure out a way to affix the other piece of Velcro to the carpeted area behind the console cover (if you affixed THAT piece of Velcro to the tub with a screw, at least it would be hidden behind the console cover).

Just some ideas... hopefully you can come up with a solution that will work & won't drive you crazy.

Bitsyncmaster
08-10-2020, 10:34 AM
I like the idea of a latch (just some L shape) screwed way back. Something that would be easy to 3D print in black or gray resin.

iflights
08-10-2020, 10:42 AM
I'd figure out something invisible. Perhaps affix some high-strength Velcro to the back of the console cover, and then figure out a way to affix the other piece of Velcro to the carpeted area behind the console cover (if you affixed THAT piece of Velcro to the tub with a screw, at least it would be hidden behind the console cover).



I really like this Velcro idea. The industrial Velcro is self adhesive. You could stick one side to the cover, and the other mating piece to the carpet under it for an invisible fix. I'm doing this later tonight.

CFI
08-10-2020, 10:58 AM
If the warped console flare bothers you now, seeing a screw (even if it has one of those covers) will make you crazy too.

Thankfully I do not fall into that category. The car is full of quirks. The concourse guys can spend their lives fixing every tiny detail but I’ve got better things to do.:)

CFI
08-10-2020, 11:01 AM
I really like this Velcro idea. The industrial Velcro is self adhesive. You could stick one side to the cover, and the other mating piece to the carpet under it for an invisible fix. I'm doing this later tonight.

This would only work as long as the carpeting is affixed in place, otherwise the console piece would just pull the carpeting away from the tub. Also, how well does the adhesive on Velcro stick to carpet?

micmak
08-10-2020, 12:02 PM
I tried to deal with this problem many many times. Eventually, I gave up. Having said that, it still annoys me and I'd still like to get those corners in tight.
Take a look at this: http://dmctalk.org/showthread.php?15174-How-to-Bend-Center-Console-to-fit-Better

.....Mike.....

louielouie2000
08-10-2020, 12:04 PM
This would only work as long as the carpeting is affixed in place, otherwise the console piece would just pull the carpeting away from the tub. Also, how well does the adhesive on Velcro stick to carpet?

This is why I was suggesting the piece of Velcro on the carpet side might need to be anchored to the tub with a screw or something. If a big enough piece of high-strength Velcro is used, there would still be plenty of contact patch despite a screw head being present.

ssdelorean
08-10-2020, 01:28 PM
My friend came up with this fix for his car. I am also using it.

- - - -

Get yourself 2 normal picture hangers and some wire.
Tie one end of the wire to a picture hanger (see Fig. 2). Hook that hanger on the drivers side center console flap and pull the wire thru from the passenger side. Thread the wire thru the second picture hanger. Push in the passenger side console flap and at the same time twist the wire tight so it pulls the two flaps toward the each other. Snip off the remaining wire and your done. Only a tiny amount of the picture hanger
is visible (see Fig. 1 & 3).


http://ohiodeloreans.com/images/tips-CenterFlaps-Lrg.jpg

64256

David T
08-10-2020, 04:14 PM
My "fix" is to get 2 strips of thin sheet metal about 1" wide and about 12" long. You can slip them into the edge along the bottom on the backside on each side. Easier to do it after removing the console. Don't screw it. The metal strips will hold the console straight and tight against the carpet. If you do use screws, one day someone will try to remove the console and not knowing there are extra screws, may damage things trying to remove the console with the screws still in there.

CriticalB
08-11-2020, 12:24 PM
My friend came up with this fix for his car. I am also using it.

- - - -

Get yourself 2 normal picture hangers and some wire.
Tie one end of the wire to a picture hanger (see Fig. 2). Hook that hanger on the drivers side center console flap and pull the wire thru from the passenger side. Thread the wire thru the second picture hanger. Push in the passenger side console flap and at the same time twist the wire tight so it pulls the two flaps toward the each other. Snip off the remaining wire and your done. Only a tiny amount of the picture hanger
is visible (see Fig. 1 & 3).


http://ohiodeloreans.com/images/tips-CenterFlaps-Lrg.jpg

64256

I'm installing new carpet this week and noticed this issue. My plan was do do something similar to your friend's fix, but instead of hooking the clip over the outside of the flap, I plan to cut a small slit in the front edge of the flap so the clip can be inserted behind the vinyl. If it works as planned, the whole setup would be invisible.

SBL
08-12-2020, 12:49 AM
My flare is at the bottom of the console cover. Well below the area where you would run a wire using the picture hanger technique.

Still thinking. One could pull back the vinyl at that bottom edge and use a small, very flat headed screw. Screw it so that the cover back is within 1/4 inch of the tub, then put the vinyl back where it belongs with some glue on the back side. The cover would not be flush with the hump, but very close and a whole lot better than it is now. Would not like it, though, if you could see the screw head.

DMC-Ron
08-12-2020, 07:40 AM
Would the magnets that folks are using for the door panels work?

CFI
08-12-2020, 08:28 AM
Would the magnets that folks are using for the door panels work?

Read post #3

Col Bennett
08-12-2020, 06:02 PM
I reinforced my center console flaps to stop them from flaring out a bit more than I’d like - especially on the passenger side. It’s a nice invisible (when installed) modification that doesn’t take too long to do.

I used a 4ft 1/8” x 3/4” flat aluminum strip from Ace Hardware and cut it to the vertical height of the existing console card support. Thinner strips bend too easily and don’t provide enough support. (The 1/8” thickness is just the right balance. There’s even wiggle room to bend it if necessary during installation.)

I then marked and drilled holes along the metal strips to make sure they didn’t align with any of the existing metal staples on the console. You don’t want to be drilling through staples!

Once the first hole was drilled, I used the bar as a guide to drill corresponding holes in the console card. Insert the first rivet by hand to hold the bar in place (don’t use your pop rivet tool yet). This will hold then bar in place to avoid it slipping while drilling. It also allows you to swivel the bracket to pull the debris/fibers from the board as you drill.

I found it helpful here to press down on the bar against the console flap on a flat surface to flatten it as you INITIALLY drill to ensure the bracket is going to help straighten it. Once you’ve got some pilot holes you can then carefully drill through each hole with the bracket swiveled to the side.

Now you have to go SLOW and be VERY careful not to punch through and damage the vinyl on the other side. There’s enough padding between the card and vinyl BUT if you go too fast and lean too hard you’ll easily puncture it. I drilled horizontally while the console was vertical to avoid applying too much pressure.

Make sure to just punch through a little when it goes through to the foam. You want those holes to be very tight - just the size of the rivet head - because you’re relying on the pop rivet to grab onto the board to hold the bar tightly in place.

Before you start to rivet the bar onto the console, go grab a hammer and flatten the staples into the console. This ensures the bar lays flush against the board.

As you can see, I used lots of rivets to support the tension between the console and the metal bar.

As for rivet size. I used aluminum rivets from Ace Hardware - 1/8” x 3/8”. The head length was perfect to bind the depth of the bar to the depth of the board - with just enough to grab the board when installed and not leave any visible dimples through the foam/vinyl.

A totally invisible fix/support for a common issue. The flap issue seems to be exasperated by the brackets that affix to the console that hold the knee pads on. My bracket was so tight it had bent the card backing on the console and caused it to lose its rigidity on the passenger side. My driver side was fine - but I did it anyway.

So there you go. A nice invisible fix to add some strength to your center console flaps.

http://content.colinbennett.com/dmc/2020-08-12_center_console_flaps_01.jpg

http://content.colinbennett.com/dmc/2020-08-12_center_console_flaps_02.jpg

http://content.colinbennett.com/dmc/2020-08-12_center_console_flaps_03.jpg