PDA

View Full Version : Spray Paint Over Spray



Bitsyncmaster
07-27-2024, 01:55 PM
I do a lot of spray painting (rattle can) for my relays. I've been doing that for many years and move about 50 feet from my daily driver. Well I washed my daily driver and noted every thing is covered with very fine particles of that spray paint.

I'm going buy a small paint booth which has fans and filter. I will use it in my garage and vent the filtered air out a window. Another thing I could do it put a car cover over the car. But I'm thinking the booth will help keep that paint out of my lungs.

Now removing that over spray is a real problem. Using IPA softens the over spray an leaves a thin film of paint. On the windows a razor blade works fine and then using a scotch brite pad with window cleaner. I think the only thing to do on the paint is to use rubbing compound.

I was under the assumption that the air born paint would dry before it landed on anything. Just a warning even using a rattle can, better use some sort of mask to prevent any paint in your lungs.

Timeless
07-27-2024, 02:10 PM
A clay bar will work. Not only removing the overspray but other contaminants that have imbedded in the paint over the years.

Bitsyncmaster
07-27-2024, 02:17 PM
A clay bar will work. Not only removing the overspray but other contaminants that have imbedded in the paint over the years.

I will have to try that. I will try anything because doing the whole car with rubbing compound will be a lot of work.

Michael
07-28-2024, 11:07 AM
Most spray paint is single stage. No sense in making it difficult. It should wipe right off with a little lacquer reducer. Just don't let the rag sit on the paint for over 30 seconds, a quick wipe and then a coat of wax and you're done.

Bitsyncmaster
07-28-2024, 11:25 AM
Most spray paint is single stage. No sense in making it difficult. It should wipe right off with a little lacquer reducer. Just don't let the rag sit on the paint for over 30 seconds, a quick wipe and then a coat of wax and you're done.

I did try a few solvents. It takes rubbing work to get it off and then leaves a smudge of paint. I tried a small spot with rubbing compound and that works good. You can quickly feel when it removed the over spray. I finished cleaning the glass with a razor blade. I tried a razor blade lightly on the paint but it did not work and takes longer than rubbing compound.

dn010
07-28-2024, 12:27 PM
Easiest is to use a buffing machine, you can get cheap ones on Amazon as long as they have multi speeds. I use Meguiar's Mirror Glaze on my painted cars, probably in your case I'd try the ultra finishing polish (205) or swirl remover.

Michael
07-28-2024, 03:16 PM
I did try a few solvents. It takes rubbing work to get it off and then leaves a smudge of paint. I tried a small spot with rubbing compound and that works good. You can quickly feel when it removed the over spray. I finished cleaning the glass with a razor blade. I tried a razor blade lightly on the paint but it did not work and takes longer than rubbing compound.

Solvent is a very generic word. Use lacquer reducer. That will be the easiest and unless you are familiar with compounds and buffing, that's a whole can of worms with the possibility of burnt paint and melted plastic trim.

10-20 minutes wiping down with a microfiber with lacquer thinner will most likely remove that paint.

Be sure to use a WHITE non colored microfiber cloth. Sometimes the colored dye can bleach into your clear.

Bitsyncmaster
07-28-2024, 04:05 PM
Solvent is a very generic word. Use lacquer reducer. That will be the easiest and unless you are familiar with compounds and buffing, that's a whole can of worms with the possibility of burnt paint and melted plastic trim.

10-20 minutes wiping down with a microfiber with lacquer thinner will most likely remove that paint.

Be sure to use a WHITE non colored microfiber cloth. Sometimes the colored dye can bleach into your clear.

I will pick up some lacquer thinner and give it a try. I would just hand rub the polish compound. I have painted cars with lacquer as a kid and know you need to use care rubbing that paint smooth.

Michael
07-28-2024, 04:27 PM
As long as you don't let a soaked rag sit on the paint or rub vigorously you should be fine. Base/clear is pretty resilient. It's ok to get on rubber trim too but some plastics will melt if you get any on them so be careful.

Really though, it should come off almost instantly. If it doesn't come off easy, then do not proceed with the reducer.

Bitsyncmaster
07-31-2024, 04:25 PM
I tried the lacquer thinner and micro fiber cloth. Does about the same as the other solvents I tried. Would really need to rub harder and longer but am worried I may damage the clear coat.

On a side note, that micro fiber cloth does wonders when cleaning the glass.

Michael
07-31-2024, 06:05 PM
I tried the lacquer thinner and micro fiber cloth. Does about the same as the other solvents I tried. Would really need to rub harder and longer but am worried I may damage the clear coat.

On a side note, that micro fiber cloth does wonders when cleaning the glass.

Wow, that surprises me that a 1k can be that tough against lacquer reducer but yeah, smart not to keep rubbing hard as it will haze and soften the clear if in contact for too long.

Bitsyncmaster
07-31-2024, 06:39 PM
Wow, that surprises me that a 1k can be that tough against lacquer reducer but yeah, smart not to keep rubbing hard as it will haze and soften the clear if in contact for too long.

What I'm thinking is any solvent softens the clear coat so removing that overspray is a little more work than using rubbing compound on the hard clear coat.

Bitsyncmaster
08-22-2024, 10:06 AM
I tried my new paint booth. It's just a cheap one from Amazon. Seems to work pretty good. Fans seem to pull enough air to keep any over spray at the back of the booth. The LED lighting is very good. I just vent the 4 inch hose out the window.

Just wonder how fast the filter will clog up with paint. There is a lot more over spray then I thought.

If I used an air brush I know it would do a better finish and less over spray but then I would need to clean the air brush each time.

Victor
08-27-2024, 09:42 PM
Airbrush too are creating overspray, although they are more fine and probably would not require you to use a spray boot. I never use this. But did use a mask. A double filter mask.
But if you want to go with an airbrush, they are super easy to clean, as long as they are gravity feed airbrush. I absolutely suggest the Iwata brand. Model HP-C, will get you cover in most applications. I have had several airbrush in my artistic life (Badger, Iwata, Devilbiss?) but have always return to Iwata. Or at least a gravity kind, for sure.
Buy a silent compressor use for stappling gun for you air. They sometimes use a refrigerator compressor.

All the airbrush hardware used to cost quite a lot back in those days. Now they are quite affordable.

Bitsyncmaster
09-25-2024, 03:20 PM
Well I love the paint booth. The rows of bright white LEDs really show the spaying even better than sunlight. Plus you don't have changing wind directions. I've used it 5 or 6 times now. I am going to build a shelf next to the window for it. Right now it's sitting on a few large cardboard boxes but it seems to just the right height.