Trailing Arm Measurements

["What The Flux?"]

Hello DeLorean Community.

I was wondering if someone could kindly help? I'm looking for any measurements of the rear suspension trailing arms please. Either left or right side. I have looked everywhere online for pictures or measurements of the trailing arms and can't find anything. The more measurements the better.

Any help much appreciated.

Thank you!

[dn010]

Any specific measurements you?re looking for? I have an old junk one sitting here.

["What The Flux?"]

Any specific measurements you?re looking for? I have an old junk one sitting here.

Hey, thank you for your kind response, I really appreciate it!

I have illustrated the measurements that I was looking for. I know I'm asking for a few, so no pressure if it's too much trouble, any measurements at all are greatly appreciated!

Thanks again for your help!

71339 71340 71341 71342

[dn010]

I have not forgotten about this, should have these for you tomorrow.

[r00b]

I have mine in good condition just sitting around from when I replaced them with stainless, if you want to buy some?

["What The Flux?"]

I have not forgotten about this, should have these for you tomorrow.

Really kind of you Dan, thank you. There's no rush, whenever works best for you. Much appreciated!

["What The Flux?"]

I have mine in good condition just sitting around from when I replaced them with stainless, if you want to buy some?

Buy some just to take a few measurements? No thanks.

[dn010]

Well, a few Fridays have come and gone, but I am here finally with the measurements. These were to the best of my ability. The Delorean Go arms pictured have a different box end where it connects to the hub carrier, and mine is pretty rotten, so the J&K measurements are not 100% accurate. If you are looking at stock arm measurements, K is close and J is as close as I could figure with the amount of rust damage. As you can see below, the stock arms have a different box end, it extends further with a cutout, compared to the D-go arms. Let me know if you need anything else.

A 5-1/32
B 4-1/8
C 2-1/4
D 30-1/4 (to beginning of where the curve begins on the bracket with the bolt holes)
E 4-3/32
F 27-5/8 (to beginning of where the curve begins on the bracket with the bolt holes)
G 5/8
H 2-1/4
I 1-7/8
J between 2-22/32&2-1/4
K 3-5/32

71438
71439

["What The Flux?"]

Well, a few Fridays have come and gone, but I am here finally with the measurements. These were to the best of my ability. The Delorean Go arms pictured have a different box end where it connects to the hub carrier, and mine is pretty rotten, so the J&K measurements are not 100% accurate. If you are looking at stock arm measurements, K is close and J is as close as I could figure with the amount of rust damage. As you can see below, the stock arms have a different box end, it extends further with a cutout, compared to the D-go arms. Let me know if you need anything else.

A 5-1/32
B 4-1/8
C 2-1/4
D 30-1/4 (to beginning of where the curve begins on the bracket with the bolt holes)
E 4-3/32
F 27-5/8 (to beginning of where the curve begins on the bracket with the bolt holes)
G 5/8
H 2-1/4
I 1-7/8
J between 2-22/32&2-1/4
K 3-5/32

71438
71439

Hey Dan, thank you for your kind help with these measurements, I really do appreciate your time. These measurements are great! I actually preferred the stock arm measurements than the DeLorean Go arms, so this is even better. I only used the Go arm pictures as reference of the measurements that I needed. I should be able to calculate the J & K measurements from the other dimensions and photo reference.

Thanks again Dan!