Log in

View Full Version : Diamond Select Flux Capacitor repair, mods and maintenance



nkemp
12-23-2025, 12:35 PM
I recently got A Diamond Select Flux Capacitor ... non-working. After getting it working, and seeing other's questions, I thought I'd post my process.

Clean the pot: First off ... If the flux caciptor is sorta working but the light speed control is wonky, it is likely due to corrosion on the potentiometer wiper. This is common on potentiometers (pot) and an easy fix. Use an electrical contact cleaner and spray into the pot while rotating the knob. FYI ... this works on old stereo equipment that sounds scratchy (I Found a Marantz receiver at the dump that after treating the pots, worked perfect ... and sells upwards to a $1,000 as is). BTW, I use Deoxit products. They include a bit of lubricant. CRC makes a cleaner only that I sometimes use as the first coarse of badly corroded parts...followed up with Deoxit.

Clean/treat the pot regardless if it is currently wonky or not. In time it will get wonky. At low voltage, the current is not strong enough to blow through the corrosion.

The first photo shows how mine was received. Not shown is that neither of the battery wires were attached to the battery case. This failure is likely due to the control knob loosening enough that the pot rotates with use. Very thin wires are used and eventually, these break from strain.

Repair (or preventive maintenance) for rotating knob:
1) There are 2 set-screws holding the knob on. Remove the knob
2) Tighten the nut really tight. Blue Loctite would help
3) Use some hot-glue to secure the pot to the undeside of the board. Avoid filling any holes!
4) If changing the wiring per below, go ahead and use larger guage wire , make it longer., and strain relief the wires ( I used hot-glue)

Wiring/Circuitry:
ON/Off Switch
The pot has two terminals on the bottom. These form a switch to turn on/off power to the circuit board.
1) one red wire connects to the battery case positive side (not marked from factory. Check battery orientation)
2) that wire connects to either of the two terminals on the bottom of the pot.
3) another red wire connects to the other terminal on the pot bottom
4) the last red wire connection is to the + pad on the main circuit board (the main board has 2 ribbon connector connected as discussed below)
5) I used hot-glue to secure and strain relief the wires

Speed Control:
The control board has two wires (yellow in my case) that wire to the pot
1) One wire (either) is wired to the center pin
2) The other wire to the left pin as you look down from the bottom (note that either should work. Wired to the left pin allows setting the speed from low to high. I've not tried it, but wiring to the right pin sets speed from high to low.)
3) note the pads on the circuit board where the two yellow wires are soldered.
4) I used hot-glue to secure and strain relief the wires

In general, if you have wires broken off, you can often get a clue by looking at the solder pads, looking for broken wire strands. Magnification can help.

Once I got the circuit wired as described, the flux capacitior worked ... in reverse as most do. It flashed in towards out.

Fixing the wrong way LED sequence.

Since they all flash in-towards-out, "all you have to do" is reverse the 3 circuit boards. Note how all the boards are connected in the center via the white/light gray 4 conductor ribbon. The ribbon is too short to simply unscrew the circuit boards and reverse the direction (so that the LED sequence is out-towards-in)
1) Unscrew the three boards via the 6 screws
2) I removed the 2 ribbons at the main board first. I did this by desoldering the wires from the board. It's putzy but in time it was removed.
3) I removed the ribbon connectors from the two remaing boards. I clammped the ribbon's free end in a vice and pulled gently on the circuit board while applying soldering iron heat to the solder pads. It takes less than a minute to remove the ribbon wire
4) Optional: Use a very small drill to open the holes a bit. The factory wires are very small and the replacement wires are larger.
5) Using four different colored wires (of sufficient length to make the connection with the board reversed (connections on the outside instead of the center as originally made)), reconnect the boards, matching the pad designations (+, 1, 2, 3)... +<->+, 1<->1, 2<->2, 3<->3. Adding flux can make soldering a lot easier even with flux core solder. Trim the wires fliush as needed
NOTE: I attached the wires from the side of the board opposite of original. This prevents the wires from being bent under the board when attached to the panel. This was optional for me and made it a bit harder.
6) Check that there are no strands touching across the pads or any solder bridges.
7) Test operation before reassembling and correct as needed (check for poor solder joints, solder bridges, and strands across pads (either side of the board.)
8 ) Screw the boards to the panel with the wire connections on the outside (not centered as originally made). Caution ... do not over-tighten the screws. I think they go into the plexiglass blocks and you don't want to crack them. On one of mine, the screw would not go tight against the board so I stopped ... and added a bit of hot-glue from the board to the panel.
9) secure and strain relief the wires with hot-glue ... just because and to clean it up a bit.

Clean up, reassemble, and enjoy.

Pictures:
As received
Main board
As now wired with correct LED direction
Closer view of rewired boards

71926719277192871929

EngineerGuY
01-14-2026, 09:44 AM
Thanks for the tips, great stuff!