PDA

View Full Version : Electrical Directional blinkers not working



Bitsyncmaster
11-15-2026, 01:42 PM
My blinkers do nothing but the 4 way flashers work fine. The schematic clearly shows the directional switch but the hazard switch is not defined. I measured the light green/brown wire going to my directional switch and I get 7.4 volts, 5 volts if the blinker is on (key needs to be on second position). I think this is the power needed for directional lights and it must come from the hazard switch. I'm guessing I will need to pull that hazard switch and buzz it out there.

Has anyone ever drawn out or logic listed how the hazard switch work?

Bitsyncmaster
11-15-2026, 08:38 PM
I found the problem. My flasher unit needs a little more load resistance on each direction side. It seems to work with just a 10 Kohm on each tail light board. Not sure if I will try another flasher or just install the resistors. 10 Kohm is really nothing (about 1 to 2 ma. only when the signal is on).

This happened when I replaced my binnacle direction indicators to low power LEDs.

David T
11-15-2026, 10:47 PM
I found the problem. My flasher unit needs a little more load resistance on each direction side. It seems to work with just a 10 Kohm on each tail light board. Not sure if I will try another flasher or just install the resistors. 10 Kohm is really nothing (about 1 to 2 ma. only when the signal is on).

This happened when I replaced my binnacle direction indicators to low power LEDs.

Standard automotive flashers require more resistance than LED bulbs can provide. Either leave the incandescent bulbs in the flasher circuit (like you have to do with the alternator bulb in the dash) or get a different flasher that works with LED bulbs and has a built-in timer. The reason the hazards still work is because (if you have the right flasher installed) the hazard lights will work even if a bulb or 2 are burnt out. The flasher not flashing in the directional circuit is a feature, not a "bug". It was meant to indicate a bulb is burnt out if it won't flash. You would then turn on your hazard lights and see which light is not flashing. The wiring in the Delorean was not designed for LED's.

Bitsyncmaster
11-16-2026, 06:11 AM
The flasher for LEDs are solid state so they do not require using the load to determine the flash duty cycle. I do have the flasher that is for LEDs. What looks like the problem is it needs to see less then a 5 volt load. If your LEDs only use one LED chip and a resistor like most indicator LEDs are set up, then the load it sees is about 2 to 4 volts (depends on the color). Most of the higher power LEDs use a string of LEDs (mostly 3 LEDs in a string). So those only provide a load above 6 to 10 volts).

Now are all LED flashers the same? Don't know that answer. Mine is about 20 years old.

My indicator LEDs are using 3 chips so many owners may find the same problem. If I installed a one chip indicator it may have worked.

Bitsyncmaster
11-16-2026, 09:14 AM
I ran another test. Drivers side needs less then 10.4 Kohms to work without the flasher relay buzzing. Passenger side needs less then 10.2 Kohms. I can do this test because I have a decade resistor box. So I'm installing a 5 Kohm resistor on each side. With temperature changes and voltage changes those tested values might change. Electronic components and LED voltage drops change with temperature.

As the seasons pass I will find if I have to use a lower resistor.

Adding the resistors to the rear light circuit boards is the easy place to solder on those load resistors.

So if your directional signals are not working, first thing to check is try and incandescent bulb in one of your signals.

DMC-Ron
11-17-2026, 09:19 AM
Has anyone ever drawn out or logic listed how the hazard switch work?

Dave,
The hazard and turn signal circuit is Labyrinthine. At least it always seemed convoluted to me. I edited the standard wiring schematics and combined the turn signal circuit with the hazard circuit, attempting to show how the hazard switch works. For clarity, the indicator lamp inside the switch is not shown.
Ron
72281

Bitsyncmaster
11-17-2026, 09:29 AM
Dave,
The hazard and turn signal circuit is Labyrinthine. At least it always seemed convoluted to me. I edited the standard wiring schematics and combined the turn signal circuit with the hazard circuit, attempting to show how the hazard switch works. For clarity, the indicator lamp inside the switch is not shown.
Ron
72281

Thanks. I pulled the switch open. The top 4 terminals have a copper "bar" that slides over them and connects most of the four when pushed. The same goes for the bottom four terminals. There is an insulator on each terminal so when not pushed it does do a few connections with cutouts on each insulator. Make sure you don't mix up the insulators if you take it apart.

DMC-Ron
11-17-2026, 10:00 AM
The flasher relays are also interesting units. The most common flashers in our vintage have an actual relay inside that closes a physical contact to send power the bulbs (see attached photo). The clicking that is heard is caused by the relay operating. It clicks whenever a load is detected on the signal connection (terminal L or LOAD). The detection of a load is done by a circuit inside the flasher that?s independent of the relay. That circuit gets activated whenever it sees a path to ground (when the turn stalk connects left or right bulbs, or the emergency hazard connects both). If the resistance to ground lowers below a set threshold, the circuit activates and begins to flash the relay.
Ron
72282
72283