Trip reset shaft broken

[Stainless]

Here is what my trip reset shaft looks like:
http://i173.photobucket.com/albums/w57/jlattin21/DSCN0325.jpg

Is is broken off right behind the lens. I may have multiple issues here because when I stick something inside to push on the shaft, the trip odometer doesn't go back to zeroes, but to random numbers. This is mostly a cosmetic issue as I think the broken shaft looks tacky, but I would also like the trip odometer to be reset to make it easier to track mileage for road trips and whatnot.

DMC sells replacement shafts, spacers, knobs, etc., so is this job doable? I haven't had to disassemble the binnacle before and I want to make sure that this is repairable before diving in.

[DMCMW Dave]

It comes with an instruction sheet. If you are comfortable working with small mechanical parts it's not bad. The biggest risk is breaking off the main dial needle when you go to remove it.

[vwdmc16]

ive installed Houston's kit, it was easy to put in, it gave me a chance to properly clean the cluster up too

[Ozzie]

Same here, replaced my broken one w/DMCH's replacement.
Not a bad job, replacing and reinstalling the cluster is cumbersome the first time.

While it's out though... that's a good time to replace most of the dash bulbs with LEDs! 8)

[jfirios]

it is so funny, the same thing happened to me when I was cleaning the dash. Sheared right off. Pain in the A$$. I would love to take apart my binicle and replace all the bulbs and put on the new trip meeter. Is it hard to work with the angle drive and re attatch it and all?

[Ozzie]

...Is it hard to work with the angle drive and re attatch it and all?

The only challenge is access related in how to get the binnacle/cluster assembly off, and back on. I've done it two times now, the first several years ago to replace said shaft, then a couple of years ago for the LED upgrade.

The technique I used was, placed small pillow by the brake pedal, put my head on the pillow and feet on the pushed back seat, then with a socket wrench and extension, took off the mounting screws (4 or 6 don't recall). I do also remember putting a u-joint like adapter between the socket and the extension, for one of the mounting bolts. Oh, and make sure you have some good lighting to work with, I my fluorescent shop light behind the brake pedal and that seemed to work well.

Removing the cluster's harness and speedometer cable is pretty straight forward. A tip I remember was to loosen the speedometer cable from the lambda counter, so you can lift the cluster, enough to be able to remove it from behind the cluster. If you leave the cable in place you won't have to snake it through later.

[wtbstuff]

If anyone has a copy of the directions and wouldn't mind posting them or emailing them to me that would be great.

thanks
Jay

[john 05141]

I look my binacle off so often... various reasons.
There are 8 or 9 screws in there. I can get the binacle out and back in 15 minutes top. But honestly, my binacle is bolted in with 4 screws only. 8 or 9 are not necessary. It has been in there like this for 2 or 3 years and stays perfectly. Makes it so much easier to remove it again.

But be careful, the bolts underneath may give scratches on your dashboard by trying to get the spedometar cable back in. and be careful to remove both sonnectors, as the flexible plastic orange "flatcable" is quite delicate. The connectors go in there.

When you put it back in, you may want to test all functions (small drive around the block) to make sure everything work before you startbolting it back on.
If you want more details, I can give them to you.

John

[tommyrich]

Another tip - from experience...the kit does not include the knob, so save the old one if you have it. Mine was broken off by the PO so it was missing and I had to re-order a new knob (that doesn't fit all that well on the new shaft).
Tom

[Stainless]

I finally got around to fixing the trip reset shaft last night. I had to remove the binnacle to replace the battery light, so I also came prepared and upgraded everything else to LED and replaced the shaft all at once. Doing all of that and putting it back in the car took approximately three hours, but that was my first time removing the binnacle, so I was going slow and steady.

Here's the binnacle removed:
http://i173.photobucket.com/albums/w57/jlattin21/DSCN0494.jpg

Back of the binnacle before disassembling:
http://i173.photobucket.com/albums/w57/jlattin21/DSCN0497.jpg

It looks messier than it really was:
http://i173.photobucket.com/albums/w57/jlattin21/DSCN0498.jpg

All back together, and the first time since I've owned the car that I've had a reset shaft:
http://i173.photobucket.com/albums/w57/jlattin21/DSCN0500.jpg

Instructions that are provided are very easy to follow and darn near fool-proof. The upgraded LEDs are awesome too :)

[Kenny_Z]

Thanks for the pictures. I need to do this soon. I guess I should order those parts today.

[jfirios]

where did you order the kits from? And the LED lights? Are the lights just plug and play kind of things?
I am interested in doing this too. What about changing the spedometer to a higher MPH one. Mine tacks out at 90 MPH I would like to get a new one that goes to 120MPH. Do you need to change anything when you replace that?

[Stainless]

where did you order the kits from? And the LED lights? Are the lights just plug and play kind of things?
I am interested in doing this too. What about changing the spedometer to a higher MPH one. Mine tacks out at 90 MPH I would like to get a new one that goes to 120MPH. Do you need to change anything when you replace that?

I ordered the trip reset shaft parts from DMCH. It didn't come in a kit, but I ordered all the parts I needed separately for less than $20. I got all of the instrument cluster LEDs from www.superbrightleds.com using a thread on here. Just search LEDs on here and you'll find the reference list of the LEDs you want.

I didn't change out the speedometer, so I don't know anything about that. I do know that I didn't reattach the needle in the correct place so my speedo now says that I'm going slower than I am. I gotta tear it back out to correct that, but luckily I am now a pro at the binnacle removal (you become a pro after doing it one time :))

[jfirios]

that might be a project to do soon.
I was wrong my spedo only goes to 85. I cant even time travel in my car. :(

[Henrik]

I ordered the trip reset shaft parts from DMCH. It didn't come in a kit, but I ordered all the parts I needed separately for less than $20. I got all of the instrument cluster LEDs from www.superbrightleds.com using a thread on here. Just search LEDs on here and you'll find the reference list of the LEDs you want.

I didn't change out the speedometer, so I don't know anything about that. I do know that I didn't reattach the needle in the correct place so my speedo now says that I'm going slower than I am. I gotta tear it back out to correct that, but luckily I am now a pro at the binnacle removal (you become a pro after doing it one time :))

I have my binnacle out and will, among other things, replace the lights in the instrument cluster. Four questions:
1. DMCH doesn't sell them?
2. If the answer to #1 is "no" and www.superbrightleds.com is a good source. Can someone help me spec out which LEDs I need?
3. How many bulbs does the instrument cluster take? (Yes, I can count but it's a good sanity check.)
4. I read in another thread that you should not replace the alternator bulb with a LED. It has to remain incandescent (stock) to work properly. Is that correct?

Thanks,

Henrik

[ccurzio]

4. I read in another thread that you should not replace the alternator bulb with a LED. It has to remain incandescent (stock) to work properly. Is that correct?

The battery bulb, yes, this is correct.

[BABIS]

is the instruction sheet available online? it didn't come with my reset shaft :(

[DMCMW Dave]

is the instruction sheet available online? it didn't come with my reset shaft :(

Send me a PM with a real name and email address and we'll get you one. Yes - it should have been in the packing (as shown in the photos above. . . .)

[Henrik]

Send me a PM with a real name and email address and we'll get you one. Yes - it should have been in the packing (as shown in the photos above. . . .)

Dave,
My trip rest shaft from DMCH didn't come with instructions either. I will PM you.

Thanks,

[sdg3205]

Anyone have a PDF of the procedure they can post or send me?

My email is [email protected]

Thanks!

[jawn101]

Anyone have a PDF of the procedure they can post or send me?

My email is [email protected]

Thanks!

Hey Dave - I found it here: http://delorean.bnebel.com/tiki-download_file.php?fileId=124 (Google)

[sdg3205]

Thank you Jon, jay and Toby for sending me the PDF!

Job completed!

[robvanderveer]

Wonderful instructions, will help me replace the front plate of my speedometer.

[alexwolf1216]

Fantastic......I think i will tackle this sometime this week since I have my binnacle out.

[alexwolf1216]

Completed last night. With these instructions, it was a breeze.

[GS450-Junkie]

Hey Dave - I found it here: http://delorean.bnebel.com/tiki-download_file.php?fileId=124 (Google)

Just did this tonight. Thanks for the link. I did, however lose the nut that goes in the shaft knob. :( anyone got a spare?

[skill]

Just did this tonight. Thanks for the link. I did, however lose the nut that goes in the shaft knob. :( anyone got a spare?

Sure do bud. I got lottsa spairs. I just finished my fixin' about 15min ago...

30931