View Full Version : Techron vs other fuel system treatments
DMC3165
04-16-2012, 07:46 PM
What makes Techron better then other fuel system treatments? I have used a combination of Techron and Marvel Mystery oil at different times to help maintain my fuel systems integrity and have had very good luck with this combination so far. But why is Techron better then say STP? Or any of the store bought fuel system cleaners?
I always hear people recommending this from professional mechanics to garage cowboys and everyone says the same thing "use Techron" but why?
DMCMW Dave
04-16-2012, 08:33 PM
I always hear people recommending this from professional mechanics to garage cowboys and everyone says the same thing "use Techron" but why?
I'm not usually a believer in "magic dust" additives, but we've had astounding results with Sea Foam.
ccurzio
04-16-2012, 08:43 PM
I'm not usually a believer in "magic dust" additives, but we've had astounding results with Sea Foam.
I'm glad to see this. On the recommendation of a friend I just recently dumped a bottle of seafoam into my fuel tank to clean the system. When I get up to Nashville next weekend we're going to seafoam the engine properly by pouring it into a manifold vacuum line.
Speaking of, Dave - do you have a recommendation as to which vacuum line would be best for this?
DMC3165
04-16-2012, 09:05 PM
Recently I had a friend of mine recommend sea-foam also. But I've never used it before and it seems more involved then just adding it at a fill up. How do you recommend using it?
ccurzio
04-16-2012, 09:15 PM
Recently I had a friend of mine recommend sea-foam also. But I've never used it before and it seems more involved then just adding it at a fill up. How do you recommend using it?
It has several uses. Adding it at fill-up is one of many, and it's the easiest and least "involved" to do. Another is to add it to the engine oil to clean out contaminants, though you need to do an oil change rather quickly after using it in this way. (On the order of around 200 to 250 miles after putting it in the oil.) And another use is to slowly pour it straight into a vacuum line that goes to all cylinders. This will blast a ton of white exhaust out of the car while it does its cleaning work.
Ideally it's good to use two cans - one in the tank, and one for the vacuum line. I'm just looking for the best vacuum line to use.
The add-to-oil option is for an engine that's in pretty bad shape. You'll know it's worked its magic when you change the oil and the old oil is borderline chunky.
DMCMW Dave
04-17-2012, 12:41 AM
Recently I had a friend of mine recommend sea-foam also. But I've never used it before and it seems more involved then just adding it at a fill up. How do you recommend using it?
Pour it in the gas tank.
I would strongly recommend against using stuff like this in the oil, especially on a neglected engine. The PRV has some internal oil screens leading to the chain tensioners. Normally not a problem, but if you start breaking loose chunks of crap in a neglected engine, they will get plugged. Among other things such as oil lines in the rocker arms..
I'm not sure what good the vacuum line treatment will do, I supposed it could break loose carbon in the cylinders (not often a problem) but it can't do anything to clean the injectors that way.
DMCVegas
04-17-2012, 03:29 AM
What makes Techron better then other fuel system treatments? I have used a combination of Techron and Marvel Mystery oil at different times to help maintain my fuel systems integrity and have had very good luck with this combination so far. But why is Techron better then say STP? Or any of the store bought fuel system cleaners?
I always hear people recommending this from professional mechanics to garage cowboys and everyone says the same thing "use Techron" but why?
Techron breaks down gum, varnish, and carbon deposits on valves. Something I like since the CIS system is always spraying them even when closed.
What's nice about Techron though is that while it's tough on carbon deposits, it's very gentle on rubber. Used Techron on the DeLorean, never had a problem. Used Berryman's B12 Chemtool as well as STP and others, and I wound up with a deteriorating fuel pump boot, and suddenly split the rubber O-Rings on the Primary Pressure Regulator inside of the Fuel Distributor. And that was just on the DeLorean. It broke some crap loose and seized up the fuel pump on an old Dakota that I used to own as well.
If you used Chevron or Texaco fuel, you're getting Techron on every use and probably don't need the extra bottle on a properly tuned car. If not a bottle of Techron dumped into your tank every once in a while doesn't hurt.
And of course here is the website to give you a better idea of what it's all about:http://www.techron.com/
ccurzio
04-17-2012, 08:52 AM
I'm not sure what good the vacuum line treatment will do, I supposed it could break loose carbon in the cylinders (not often a problem) but it can't do anything to clean the injectors that way.
Exactly right. The first can is for the tank to clean the injectors. :)
I know the carbon deposits are rarely a problem in the cylinders, but I'm working on hammering out some engine issues and I'd like to get everything cleaned internally as much as I can without actually taking the engine physically apart. That being said, which vacuum line would you say is best to use? Something that goes to all cylinders equally, obviously.
DMCMW Dave
04-17-2012, 11:05 AM
Exactly right. The first can is for the tank to clean the injectors. :)
I know the carbon deposits are rarely a problem in the cylinders, but I'm working on hammering out some engine issues and I'd like to get everything cleaned internally as much as I can without actually taking the engine physically apart. That being said, which vacuum line would you say is best to use? Something that goes to all cylinders equally, obviously.
The two ports on the cold start injector feed all 6 cylinders through special runners on the bottom of the intake. Equally? As equally as the cold start injector does. Any other vacuum port on the intake runners only feed one side or the other.
ccurzio
04-17-2012, 11:29 AM
The two ports on the cold start injector feed all 6 cylinders through special runners on the bottom of the intake. Equally? As equally as the cold start injector does. Any other vacuum port on the intake runners only feed one side or the other.
So I guess it would just be a simple matter of removing the CSV and pouring it down that paricular line?
Chris4099
04-17-2012, 12:33 PM
They make SeaFoam in a spray bottle now.
http://www.seafoamsales.com/sea-foam-spray.html
That's what I used. I simply removed the air cleaner, put some shop towels around the intake and with the engine running at about 2K RPMs, I sprayed the SeaFoam right into intake (half a bottle). It splashes a little bit off the air meter plate, so that's what the shop towels are for. You get lots of smoke both during and after the application. Once done, it seemed to run a little smoother and have quicker throttle response. Unfortunately I didn't feel like taking the engine apart both before and after to see how well it did with carbon removal. :)
As for Techron, I run a bottle through the tank about once a year. I normally use Chevron gas (or other Top Tier), but I figured it doesn't hurt to give the injectors an extra cleaning. One tip I heard was if you are about to go on a long drive, put the cleaner in then. That way it gets run through the system as quickly as possible and won't put any stress on the rubber parts. Just make sure to put in another full tank of gas afterwards to dilute any remaining cleaner.
82DMC12
04-17-2012, 01:15 PM
I would definitely ***NOT*** just "pour" a bottle of seafoam into a vacuum hose. Right after high school I worked at a quick lube and we used to sell a complete fuel system cleaning package.
This is the package: http://www.amazon.com/3M-Intake-System-Cleaner-3-Pack/dp/B000ALCOMG.
You also need this: http://tinyurl.com/cx6grys
You would hang the first can in the top link from the hood latch upside down and connect the hose to it. Then you would get the S-shaped end of the hose into the throttle body so that it would spray directly down the throttle. There is a brass knob on the hose so that you can finely tune the flow of cleaner. The idea is you wanted a fine mist coming out and not get all drippy or a steady flow of liquid. This kit actually worked pretty well.
Before that, we had a less sophisticated cleaning system that had a simple IV-drip kind of hose that you would just stick into a vacuum hose, usually something big like the brake booster hose. On that thing you could tune it so it was a slow drip (ideal) or a steady stream. Sometimes a stupid tech would try to make it go too fast, get a steady stream going, open the throttle, and it would blow white smoke like crazy. If he let the foot off the gas the engine would usually start knocking LOUDLY from hydrostatic lock and I saw it kill a few engines that were very hard to restart. I can't imagine the damage possible or what that stuff would do washing into the oil from an engine flooded by it. Which is exactly what would happen by just pouring a bottle of seafoam into a vacuum hose.
My suggestion is if you really have to do this, get the 3M kit. I don't know what actual benefits there is though besides possibly cleaning carbon off the pistons. I have the intake mainfold off a D right now and I can see all of the intake valves are covered in black soot - but so what? It doesn't do anything, all that matters is the valve seat is good. Might as well leave it alone instead of letting it jam up into the combustion chamber.
Andy
ccurzio
04-17-2012, 01:19 PM
I would definitely ***NOT*** just "pour" a bottle of seafoam into a vacuum hose.
Uh... You do realize that you don't just dump the entire bottle into a vacuum line and leave it at that. You pour around half a bottle in VERY SLOWLY a little at a time. Otherwise, that's what you're supposed to do. It's fine.
That kit accomplishes the exact same thing, except with added expense.
82DMC12
04-17-2012, 03:16 PM
Yes, and in post #10 you asked "So I guess it would just be a simple matter of removing the CSV and pouring it down that paricular line?". I have seen and heard things so scary come from engines because of people who pour liquid into a vacuum hose that I thought my personal experience of probably running an intake cleaner on hundreds if not thousands of cars would be helpful to anyone reading this thread some time in the future. If they want to do it without risking damage, there are options.
Andy
Uh... You do realize that you don't just dump the entire bottle into a vacuum line and leave it at that. You pour around half a bottle in VERY SLOWLY a little at a time. Otherwise, that's what you're supposed to do. It's fine.
That kit accomplishes the exact same thing, except with added expense.
stevedmc
04-17-2012, 03:42 PM
I did the Seafoam treatment on my Geo Metro a few weeks ago and it seemed to help out with idle. This is what I did:
1. Poured 1/3 of a bottle in my fuel tank.
2. Poured 1/3 of a bottle in my engine.
3. While my engine was hot and running I slowly poured the remaining 1/3 of a bottle into my throttle body while reving the engine to prevent vapor lock. While doing this there was plently of white smoke/steam coming from the exhaust. It was pretty amusing because I did this while in a parking lot.
4. I drove the car a little over a hundred miles and then changed my oil.
From what I understand, doing this as regular maintenance can be a good thing. My Geo Metro didn't blow much white stuff out of the exhaust (after the treatment) because the engine is new (barely 2 years old) and I'm sure it didn't have many deposits. Pouring this stuff into a running engine could be a nightmare on a 30 year old car if it breaks up carbon and it gets stuck somewhere. Plus, do you really want to be standing by the exhaust when all that white stuff starts puffing out of the exhaust?
Yes, and in post #10 you asked "So I guess it would just be a simple matter of removing the CSV and pouring it down that paricular line?".
I wouldn't pour this stuff into a running engine that is 30 years old but if you do there is no reason to really pour it. All you need to do is put the stuff in a cup and then use a vacume line to gently suck the stuff into the engine. This is the easiest way and allows you to regulate how much goes into your engine at a time.
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.