View Full Version : The Restoration of #1768
jawn101
11-12-2013, 12:03 AM
Treated my self and the car to something nice
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_1139_zpsa0baeeed.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/IMG_1139_zpsa0baeeed.jpg.html)
First time the car has had completely new front shocks in 32 years, Below are the shocks Ive run before. Right to left: Stock Girling (off a 18kmile car), DMCH Eibach (used with 30k miles and one ended up being blown so ive never actually used these more the a trip around the block so Still need to find a place to rebuild them), New Koni Adjustables, Mazda Miata rear Bilstein HDs with a few seasons of racing on them.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_1142_zpsaf6ef6bd.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/IMG_1142_zpsaf6ef6bd.jpg.html)
These Konis are modifed Pontiac Fiero front shocks (Koni #8040 1092). The lower bushing was pressed out and a urethane bushing with a 1/2" ID sleeve was installed, they are adjustable by compressing the shaft fully and rotating it within a 720' window, I started out in the middle adjustment and they are a noticeable improvement over the Girlings and the (worn) Billys. There is a slight amount of residual bouncing if you bounce the car up and down on one corner so Im going to set them a bit stiffer but while driving they feel devine
I would like to get another pair of new Bilsteins and do the same bushing treatment and compare them back to back with the konis since my experience with the Bills are not fair since they were used cast offs I got in a trade years back.
Installed easy just like a stock shocks ad you can see they are barely smaller.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_1145_zps0d31748f.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/IMG_1145_zps0d31748f.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_1146_zps67180306.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/IMG_1146_zps67180306.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_1147_zps3b72d860.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/IMG_1147_zps3b72d860.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_1148_zpsf6f3f5b4.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/IMG_1148_zpsf6f3f5b4.jpg.html)
Those look great! So they really feel obviously different?
Chris Burns
11-12-2013, 12:23 AM
That's the first time I have heard of a Eibach shock going bad.:jawdrop:
vwdmc16
11-12-2013, 12:35 AM
Oh yeah, shocks can fail, the bad one I have has a leak and has lost some oil and all gas pressure.
@ Jon, Yes it has much more refined feel over speed bumps and bad pavement. They have a tighter feel and the front doesnt dive as much under hard braking, Its still no new BMW but it never will be with the suspension design flaws we have.
Thanks for the comparison, very interesting!
Do you think these Koni are better than the Spax (plug&play) design for the DeLorean?
On the other hand, I have some Koni's shock on my everyday car and they have more than 240000kms on them :)
vwdmc16
11-12-2013, 11:10 PM
Im afraid i cant speak for the Spax as i have no experience with them but i have only heard good things
vwdmc16
02-03-2014, 12:15 AM
It's been a while since any large projects on the Delorean. The car has been behaving quite well. Just about to hit 60k miles I bought some new wiring supplies for a long term project: replacing all the factory multi-pin connectors with some modern quality weatherproof Deutsch connectors. Also dressing up the wiring with some braided Nylon loom. First Ill do a few small sections, Like the rear fascia wiring harness. First have to de-pin the connector to fit the loom and heat shrink over. Used this tool to pull the pins out.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_1163_zpsdaabfe37.jpg
Here is some of the loom, it can stretch and shrink easily.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_1164_zps43b66d22.jpg
After some 3/4" heat shrink is applied, It secures the loom on tight.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_1166_zps813f1c97.jpg
I cleaned up the connectors with this sanding pen, It uses glass fibers to clean the metal.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_1165_zps3c9823be.jpg
Also dressed up the A/C clutch power wire and the cold start temp sender wire.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_1170_zps5b61a013.jpg
Here is one of the new 9 pin connectors I will try out, first one to change is the connector for the front fascia wiring which has become rather dirty over the years.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_1167_zpsf12ff90e.jpg
jawn101
02-03-2014, 12:19 AM
It's been a while since any large projects on the Delorean. I bought some new wiring supplies for a long term project: replacing all the factory multi-pin connectors with some modern quality weatherproof Deutsch connectors. Also dressing up the wiring with some braided Nylon loom. First Ill do a few small sections, Like the rear fascia wiring harness. First have to de-pin the connector to fit the loom and heat shrink over. Used this tool to pull the pins out.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_1163_zpsdaabfe37.jpg
Here is some of the loom, it can stretch and shrink easily.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_1164_zps43b66d22.jpg
After some 3/4" heat shrink is applied, It secures the loom on tight.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_1166_zps813f1c97.jpg
I cleaned up the connectors with this sanding pen, It uses glass fibers to clean the metal.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_1165_zps3c9823be.jpg
Also dressed up the A/C clutch power wire and the cold start temp sender wire.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_1170_zps5b61a013.jpg
Here is one of the new 9 pin connectors I will try out, first one to change is the connector for the front fascia wiring which has become rather dirty over the years.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_1167_zpsf12ff90e.jpg
Awesome! I really like how that loom ends up looking in there, especially over some of those bundles that get really crunchy over time. I'd do the wires to the starter/oil pressure sender too - do you think that wrap can take the heat right there?
vwdmc16
02-03-2014, 12:32 AM
Yes I will try to do all the visible wires eventually. The stuff can handle -94' to 257' it melts at 482'. I would like to cut down on the excess wires on the starter/alternator harness too.
DavidProehl
02-03-2014, 01:24 AM
Very clean looking! That des simplify and modernize the look while providing extra protection.
Oh man i need that tool! I got mine out but all the pins are garbage. Im running all new wires anyway, but this would have made things much easier.
vwdmc16
02-03-2014, 04:11 PM
For sure it helped a lot. It was in my new Deutsch connector tool kit and just happened to fit.
Ryan King
02-03-2014, 05:00 PM
Just went through this WHOLE thread for the first time. Wow! Awesome stuff. I look forward to the day when I have a second car so I can take some time and refurbish my car like you've done yours.
jawn101
02-04-2014, 12:36 AM
Just went through this WHOLE thread for the first time. Wow! Awesome stuff. I look forward to the day when I have a second car so I can take some time and refurbish my car like you've done yours.
Yep, Clint's a badass. You should come up our way sometime and meet the locals :)
Ryan King
02-04-2014, 01:39 AM
Yep, Clint's a badass. You should come up our way sometime and meet the locals :)
I was just saying that to him!! I would love to come up. Are you guys doing any Tech Days soon-ish? There is another local owner here that I am sure would want to join!
vwdmc16
04-19-2014, 01:19 AM
Yeah Ryan, Im planning on hosting a big tech day at my place this season, pulling my engine or something. I will post up when it gets closer.
After many years I finally got my Delorean back onto a chassis Dyno, Kinda disapointing what the WHP is, this is a different brand dyno and yeah alot has happened in the 4 years since I dynoed before. This is a Dynocom 5000 dyno, Just compared a BMW I built at work on this dyno vs a known accurate Dynojet that it ran the day before. This dyno was about 7% lower than the DynoJet readings.
The Mustang Dyno that I ran my D on years ago gave a best of 114hp/ 145tq
The Dynocom gave a best of 105hp/ 156 tq
With the 7% correction a dyno jet "should" put out 112hp/ 167 tq
No idea where all this extra torque came from.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/th_20140418_174031_zps99736c26.jpg
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/th_20140418_174038_zps983cee41.jpg
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/th_20140418_182530_zps84aa5054.jpg
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/th_20140418_182605_zps50db56a8.jpg
opethmike
04-20-2014, 12:59 PM
Those are better than stock numbers. What mods have you done? Apologies if you stated that already in the thread.
Another Marty
09-28-2014, 12:16 AM
It was a cold, rainy day here in SLC, UT today. And I have been looking for inspiration to start on VIN 2193. This thread did it, I believe. Spent a couple of hours reading through the pages. Great work. And that car is so much better off these days. Congratulations. :)
vwdmc16
09-29-2014, 03:20 AM
Glad you enjoyed the read, I've put alot of work into documenting the repairs. It has been a while since i have updated but more is coming.
vwdmc16
11-03-2014, 01:28 AM
Those are better than stock numbers. What mods have you done? Apologies if you stated that already in the thread.
Ive done quite little, MSD Coil, cold air intake, and bumped the timing up 3 degrees, also did a bit of port matching on the exhaust manifolds But mostly I think its just a solid motor, Some of the other local owners have driven it and agree it feels peppier than theirs.
jawn101
11-03-2014, 01:52 AM
It does feel fast. Don't forget your elimination of the ballast resistor!
vwdmc16
12-12-2014, 11:15 PM
Hi everyone, its been about six months since I had a proper update. Ive been pretty busy, but not on the Delorean. I finally had the chance to finish building a car that I got about a year before the Delorean and it has been waiting patiently for six years. Well let me back up a bit and tell it's story.
This is a brief overview of the build of my 1975 Volvo 242 the "V8olvo". About 7 years ago I helped build a cheap race car for some customers, its was an 84' Volvo 244 with a 1985 Mustang drivetrain and was set up for road racing, I fell in love with the sound, the feel and uniqueness of the car but I wanted to be able to drive it on the street too. That same customer found me this car, a '75 (first year of the 200 series and smog exempt in Cali) that had been sitting in a forest since 1988! He pulled it to build a second car but ended up selling it to me for $200.
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/18rifgtls9xfyjpg_zps038ea80a.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/18rifgtls9xfyjpg_zps038ea80a.jpg.html)
It was rough but back then I was ready to take on any project! I quickly began stripping the nasty rot that the forest had caused.
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/101_2670.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/101_2670.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/101_2660.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/101_2660.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/101_2668.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/101_2668.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/1499570_711694138874777_1050292209_n_zpsa09ca84b.j pg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/1499570_711694138874777_1050292209_n_zpsa09ca84b.j pg.html)
With a clean slate I could mock up the new power plant
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/100_3691.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/100_3691.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/100_4585.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/100_4585.jpg.html)
There is plenty of room for a big v8, Made my own engine mounts and modified the trans mount to connect to the Ford T5, It fit amazingly well.
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/IMG_3449.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/IMG_3449.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/IMG_3448.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/IMG_3448.jpg.html)
However I soon had to quit the job I had and didnt have the room and tools to continue the build so The car sat like this for 6 years in storage.
But Earlier this year I again had the time, space and tools at me disposal to finally build the beast. My new plan was to make the underhood very clean even if the exterior was faded and dented. I had to start with nothing in the engine bay, all the wiring was cut off at the firewall as mice had destroyed nearly every inch. I also filled and shaved any unneeded holes or brackets
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/10011241_732186006825590_1831400874_n_zps285cc04c. jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/10011241_732186006825590_1831400874_n_zps285cc04c. jpg.html)
I was able to modify mustang headers to fit but it was still very tight, This is a part I plan on redesigning soon. I also tweeked the engine and trans mounts to improve placement for balance and maintenance.
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/newheaders_zpsfc82f1b2.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/newheaders_zpsfc82f1b2.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/transmount_zpsfb901b0b.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/transmount_zpsfb901b0b.jpg.html)
My old T5 transmission I used before was stolen so after I got another and better one I was able to make a new shifter handle.
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/shifter_zpsdad6ada5.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/shifter_zpsdad6ada5.jpg.html)
jawn101
12-12-2014, 11:33 PM
The most important question is - does it drive yet?? :)
vwdmc16
12-12-2014, 11:45 PM
Full exhaust was built too, 2.25" from the headers with V band connectors, then merged to 3" back. very similar to the set up on that race car many years ago.
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/exhaustin_zps24957ce1.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/exhaustin_zps24957ce1.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/exhaust_zps668a2cf9.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/exhaust_zps668a2cf9.jpg.html)
The brakes were shot, I couldnt even get them apart to rebuild so some reman calipers were installed, these are the larger brakes from the 80's Turbo models, All new rotors, lines, junctions, Master cylinder too
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/brakes_zpsc2a66352.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/brakes_zpsc2a66352.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/100_3750.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/100_3750.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/cleanstrut_zps06d4c7b2.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/cleanstrut_zps06d4c7b2.jpg.html)
Many other little jobs ate up my evenings and weekends, restoring the fuel tank, new front suspension bushings, cleaning, painting. No dirty parts were put back on the car, That was my #1 rule. Finally the engine bay was ready for primer.
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/primer_zpsffd25398.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/primer_zpsffd25398.jpg.html)
Then factory Cascade White paint, Not spray paint but proper automotive hardened urethane:
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/painted_zps3c1d5ec8.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/painted_zps3c1d5ec8.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/906660_835856866458503_6765339198875428395_o_zpsef 130537.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/906660_835856866458503_6765339198875428395_o_zpsef 130537.jpg.html)
Now I needed a new engine, The old one I had planned to use had rusted out in the years sitting in the elements and it was a junk older block anyways,
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/mockup_zpsbbd77586.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/mockup_zpsbbd77586.jpg.html)
I picked up this '87 long block which has the roller valve train and better internals. I stripped it, measured it out, Rebuilt it withe bearings rings, seals, better heads too.
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/donor_zpsa73b5857.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/donor_zpsa73b5857.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/longblock_zpsfb9e764c.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/longblock_zpsfb9e764c.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/enginebuilt_zpsd589ebe7.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/enginebuilt_zpsd589ebe7.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/hoist_zps69a89bd1.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/hoist_zps69a89bd1.jpg.html)
Now final assembly could begin.
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/enignein_zpsaacb48cd.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/enignein_zpsaacb48cd.jpg.html)
I also found a decent used interior, not as cool at the retro Red but it was a good deal and had like new seatbelts too.
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/carpet_zps00ffc158.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/carpet_zps00ffc158.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/bench_zps3a0e149c.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/bench_zps3a0e149c.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/seats_zpsc4077598.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/seats_zpsc4077598.jpg.html)
Re wired the front end and tucked the harness inside the fender to hide it.
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/v8wiring2_zps81421b62.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/v8wiring2_zps81421b62.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/v8wiring1_zpsc3613cde.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/v8wiring1_zpsc3613cde.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/20141207_041153_zps5da5f600.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/20141207_041153_zps5da5f600.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/20141207_074042_zps8f4cdf7e.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/20141207_074042_zps8f4cdf7e.jpg.html)
Rear mounted battery needed heavy cabling to transmit the power.
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/wiring_zps7cd1577a.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/wiring_zps7cd1577a.jpg.html)
Then all the little details, throttle cable, heater hoses, starter power, alternator wiring,belt routing, custom drive shaft, clutch cable etc.
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/enginebay_zpsa5ec3c17.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/enginebay_zpsa5ec3c17.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/hoses_zps7ad67474.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/hoses_zps7ad67474.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/throttle_zps3d53c0c0.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/throttle_zps3d53c0c0.jpg.html)
Last weekend I took her for her first test drive in 26 years! it was great, but the car still needs work so I can drive it everyday, Then stage 1 begins, shocks, springs, swaybars, camber plates, lumpy cams, EFI.......
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/20141207_113614_zpsa2d8a0fd.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/20141207_113614_zpsa2d8a0fd.jpg.html)
Thanks for looking.
jawn101
12-13-2014, 01:21 AM
Well that answers that!! Too freaking cool man. I can't wait to take a spin :)
DMC5180
12-13-2014, 10:19 AM
A sleeper! 😏
DavidProehl
12-13-2014, 11:55 AM
Looks brand new! Can't wait to see it in action!
vwdmc16
12-22-2014, 11:31 PM
2015 will be the year of the Delorean, or at least my Delorean. Here is a preview of some of the projects in play:
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/spec1a_zpsa457a814.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/spec1a_zpsa457a814.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/bilstein_zps42db0b8d.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/bilstein_zps42db0b8d.jpg.html)
vwdmc16
11-15-2015, 05:03 AM
Back again, nearly a year later. Man i have been really slacking, not a huge amount to report however but lets catch up. I have mostly been busy at work and constantly tinkering on the V8volvo project so the Delorean has had it's quietest year since ive owned it. Only put on about 3k miles too, the least ever and there has been a reason for that, 2015 didnt work out to be the Year of my Delorean like I hoped, Ive hit (literally) a few snags.
Back in February I finished up my Bilstein rear shock swap and have put about 2800miles on them since. They have been great, you can check out all the details on how they were made on this thread:
http://dmctalk.org/showthread.php?11373-Bilsteins-for-the-Rear-of-the-Delorean
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150126_225740_zpsydtzhuno.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150126_225740_zpsydtzhuno.jpg.html)
In march I installed and did a dyno test of the Stage One exhaust which you can read about here:
http://dmctalk.org/showthread.php?11587-Stock-Exhaust-vs-Stage-1-Exhaust-Dyno-Tested-Results!
http://i31.photobucket.com/albums/c396/vwdmc16/Dmc%20exhaust%20mods/IMG_1307_zpsorssg2yk.jpg
http://i31.photobucket.com/albums/c396/vwdmc16/Dmc%20exhaust%20mods/IMG_1326_zpsadjo18i8.jpg
Now I did a rather interesting project back in August 2014 but I never posted about it as I wanted to keep it as a surprise for the local DMC club guys to see, then I forgot to post up about it here after that. So I will explain it now as it will help ( you can see in in these following pics), I was unhappy with the stock steering rack from day one and was always on the look for a better alternative. I drove a local car with a new rack but was still not happy with the feel and tightness. The Delorean needs a wide and thin rack with a small pinion area so it would fit in the frame of the front crush tubes, after years of familiarly with Mazda Mx5 race cars I grew to appreciate and respect the great quality of the steering rack in those cars made by Toyo Kogo. I opted to go with a non power rack from a base model 1991 Miata. I may upgrade to a Depowered hydraulic rack as they have a faster ratio.
I will post a new separate thread about the MX5 rack conversion when I get my pictures off my old PC. Things were going ok by April, that is except the head gasket was still getting worse, I had a combustion chamber to water jacket leak that would start over pressurizing the engine cooling when it got to temp and had more than a light load, So the car was still drivable but effectively only had a 30 mile range, Recently it has gotten much worse so that is my 2015 winter project. That is a story for the next installment...
But Then I Crashed....
Then on the morning of April 10th a momentary lapse in judgement allowed me to crash my car into a thick curb in a parking lot near my work. I didnt see it until it was too late, the impact was at about 10 mph and hit the passenger front frame area hard, nobody was hurt and luckily nobody saw me do it either. Thankfully I didnt get high centered on the cement and it wasnt quite tall enough to damage the Fascia but it did shear the right side sway bar mount off. I was able to limp the one block back to my shop to inspect what my stupidity did.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150410_183824_zpswmj4orgf.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150410_183824_zpswmj4orgf.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150410_183829_zpszoyogocm.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150410_183829_zpszoyogocm.jpg.html)
Radiator lower mount ripped too and caused a very minor weeping leak. I was planning to upgrade to the DMCEU aluminum anyway!
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150410_183844_zps2aohka93.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150410_183844_zps2aohka93.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150410_183906_zps7xs1p71e.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150410_183906_zps7xs1p71e.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150413_181436_zps18zuxncq.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150413_181436_zps18zuxncq.jpg.html)
You can see how the sway bar mounting studs I installed years ago help up, the original welded nuts were stripped so I installed studs.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150413_181448_zpsovl6dzjx.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150413_181448_zpsovl6dzjx.jpg.html)
After the inspection I decided that trying to straighten the crumble tubes was not an option and I briefly considered looking into getting another frame as that was still my plan from all the rust damage and repairs this one had from years ago. Next I put the car on an alignment rack and found that suspension wise, the car wasnt actually bent, The caster was way off but that was from having no front sway bar attached. Camber was just fine and the toe is going to be sorted when the rack it reinstalled in the front end. I knew that replacement crumple tubes are availble for the rather steep price of $1200 and Im a fabricator that builds Race cars for a living so I wouldnt have to pay to have that installed by someone else either. But then I got to thinking overnight, Ive never liked the weak design for the factory front frame anyways. Why not design my own??? This would become the first step to totally redesigning the front suspension on my car.
So I just cut the whole thing off and started over:
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150413_200359_zpseccyvxtd.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150413_200359_zpseccyvxtd.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150413_211845_zpsrr0slyyb.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150413_211845_zpsrr0slyyb.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150414_183206_zps4ztegx8h.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150414_183206_zps4ztegx8h.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150414_183225_zpskamom2wf.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150414_183225_zpskamom2wf.jpg.html)
New 1/8" steel on the front and bottom to create a strong foundation, No more worrying about denting the bottom of the frame with jack stands either. I spent alot of time with a wire wheel and sanding disc to finally rid the frame of rust and old epoxy, everything was sprayed with a good coat of weld through primer to keep the rust gone.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150415_200324_zpsnwtpabbo.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150415_200324_zpsnwtpabbo.jpg.html)
Then two pieces of 1.5x.120 DOM roll cage tubing bent in my tubing bender form the main two frame horns, with some 1 x.120 DOM braces. lots of measuring and trimming to get this square and level.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150416_213527_zpseezcznps.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150416_213527_zpseezcznps.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150416_213609_zpsrss2yidg.jpg
Now to mount the Miata steering rack, More tubing modified to make a clamp on system that will securely hold the rack and allow adjustments if I didnt get it quite centered.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150418_163505_zpsw9jin50q.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150418_163505_zpsw9jin50q.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150418_172101_zpsf1i2jsto.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150418_172101_zpsf1i2jsto.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150418_183206_zpsxhlpumnz.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150418_183206_zpsxhlpumnz.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150418_183315_zpskd62hxcp.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150418_183315_zpskd62hxcp.jpg.html)
Now the Sway bar:
Mounts were built but only tacked up, I would leave this weld for last. Using the Alignment rack I could get the Caster dead even left and right, better that before the crash. Also straighten the radiator and rebuilt its mounts too.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150418_214144_zps6n88wnq2.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150418_214144_zps6n88wnq2.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150419_145509_zpsvjq0okzw.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150419_145509_zpsvjq0okzw.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150419_154541_zps2tzzm023.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150419_154541_zps2tzzm023.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150419_171355_zpsbfopsnuk.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150419_171355_zpsbfopsnuk.jpg.html)
The steering rack also was installed slightly higher that it's original stock position, This would help remove bump steer on my lowered car.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150419_171616_zpslcl0hf1w.jpg
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150419_203237_zpsstirbtkn.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150419_203237_zpsstirbtkn.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150419_203254_zpsivkkpimi.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150419_203254_zpsivkkpimi.jpg.html)
Fully welded and stronger and straighter than ever, I could even jack the car up from the new cross tube which is much easier that reaching all the way to the front axle centerline on such a low car. I could now take her home after about 35 hrs of work and take it all apart again to spray on some fresh paint.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20150427_184709_zpsaobcham8.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20150427_184709_zpsaobcham8.jpg.html)
Amazing job done on the front of the car :wrenchin:
88KPH
11-15-2015, 04:44 PM
Yeah nice work Wolfie!
Intrigued.... Dealing with high spec race cars, in your fully kitted workshop, etc....... Why a Delorean?
vwdmc16
11-15-2015, 05:23 PM
Delorean is still my dream car, ever since I was 5, but building BMW race cars pays the bills right now. I wont lie, I get to build alot of neat stuff, It all starts out with raw tubing and plate, and a regular street car. I do 100% of the work from stripping it down, rewiring, fabricating the cage, all brackets, windows, vinyl, paint, even assemble the engines and drive train. Everything but drive them
http://i31.photobucket.com/albums/c396/vwdmc16/other/IMG_20150619_165123_zpsmrreiopz.jpg (http://s31.photobucket.com/user/vwdmc16/media/other/IMG_20150619_165123_zpsmrreiopz.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/other/IMG_20150902_103944_zps30dg5lql.jpg (http://s31.photobucket.com/user/vwdmc16/media/other/IMG_20150902_103944_zps30dg5lql.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/other/IMG_20150624_202035_zpskiyy1a4q.jpg (http://s31.photobucket.com/user/vwdmc16/media/other/IMG_20150624_202035_zpskiyy1a4q.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/other/IMG_20150812_154313_zps3oth0kaj.jpg (http://s31.photobucket.com/user/vwdmc16/media/other/IMG_20150812_154313_zps3oth0kaj.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/other/IMG_20150918_184307_zpselke2m6t.jpg (http://s31.photobucket.com/user/vwdmc16/media/other/IMG_20150918_184307_zpselke2m6t.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/other/IMG_20150915_184239_zpskkt5ghs7.jpg (http://s31.photobucket.com/user/vwdmc16/media/other/IMG_20150915_184239_zpskkt5ghs7.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/other/IMG_20150811_171659_zpsmtzgcp6k.jpg (http://s31.photobucket.com/user/vwdmc16/media/other/IMG_20150811_171659_zpsmtzgcp6k.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/other/IMG_20150527_094005_zpspo1y74wl.jpg (http://s31.photobucket.com/user/vwdmc16/media/other/IMG_20150527_094005_zpspo1y74wl.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/other/IMG_20150602_114141_zpsqqyn6atv.jpg (http://s31.photobucket.com/user/vwdmc16/media/other/IMG_20150602_114141_zpsqqyn6atv.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/other/IMG_20150626_152051_zpsnil3afrh.jpg (http://s31.photobucket.com/user/vwdmc16/media/other/IMG_20150626_152051_zpsnil3afrh.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/other/IMG_20150327_111812_zps7aawwexj.jpg (http://s31.photobucket.com/user/vwdmc16/media/other/IMG_20150327_111812_zps7aawwexj.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/other/IMG_20150318_143012_zpshkekq0bw.jpg (http://s31.photobucket.com/user/vwdmc16/media/other/IMG_20150318_143012_zpshkekq0bw.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/other/IMG_20150708_212041_zpsn8hs0som.jpg (http://s31.photobucket.com/user/vwdmc16/media/other/IMG_20150708_212041_zpsn8hs0som.jpg.html)
Bitsyncmaster
11-15-2015, 05:35 PM
Nice work. Some guys have all the luck securing a job like that.
88KPH
11-15-2015, 05:39 PM
Neat, Can I do the driving then? Seems fair!
I'd love to see a Delorean given that treatment. Go on, you know you want to, you've even made a start on the front of yours!
DMC5180
11-15-2015, 05:57 PM
I'd love to see a Delorean given that treatment. Go on, you know you want to, you've even made a start on the front of yours!
Well, it's been done by putsch racing.
http://dmctalk.org/showthread.php?12522-Custom-built-racing-Delorean-by-Putsch-Racing
Dennis
88KPH
11-15-2015, 06:09 PM
Cheers for that Dennis, love it, at last a Delorean that go's like it looks!!
vwdmc16
11-16-2015, 02:50 AM
My plans are a much more hard core race car, no longer street legal. ...
Well, it's been done by putsch racing.
http://dmctalk.org/showthread.php?12522-Custom-built-racing-Delorean-by-Putsch-Racing
Dennis
jawn101
11-16-2015, 06:36 PM
Clint is unstoppable. That's all I have to say about that - there's nothing this guy can't do. I've seen it! :)
vwdmc16
01-24-2016, 09:33 PM
Since im so "unstoppable" I better keep updating. I will update to a more current set of events. Ive begun to rebuild the engine and transmission. While the drivetrain is out I repaired the last of the rot.
So the engine is pulled and the car put on a trailer.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_20160103_142918_zpsbld9w9m5.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/IMG_20160103_142918_zpsbld9w9m5.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160116_134554_zpsa9sx0cwg.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160116_134554_zpsa9sx0cwg.jpg.html)
Back on the lift at Kontrolle. Sanded off alot of the nasty old paint and epoxy.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160116_214352_zpsiitrm3hu.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160116_214352_zpsiitrm3hu.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160116_140922_zpspdswx4nv.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160116_140922_zpspdswx4nv.jpg.html)
looking better, but now to cut out the rot on the passenger side rail where a water pipe mount is located.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160116_214328_zpsxwhel3ht.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160116_214328_zpsxwhel3ht.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160116_183613_zpsngmszc9d.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160116_183613_zpsngmszc9d.jpg.html)
Old metal removed and new plate covers the hole and makes the frame stronger.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160116_185553_zpsuxjtlm3q.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160116_185553_zpsuxjtlm3q.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160116_230759_zpsp5it59ft.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160116_230759_zpsp5it59ft.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160116_214339_zpsvisymucn.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160116_214339_zpsvisymucn.jpg.html)
Next I decided the rear frame support needs to be removable, so I carefully cut it off and make these new plates with welded in nuts to re attach the bumper.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160116_230718_zps8tefshl9.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160116_230718_zps8tefshl9.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160116_230725_zpsge0fiv02.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160116_230725_zpsge0fiv02.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160116_230743_zpsgbx2m7e6.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160116_230743_zpsgbx2m7e6.jpg.html)
vwdmc16
01-24-2016, 09:39 PM
Here is a quick update on the engine too. Most parts have now been cleaned.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20151212_125939_zpsqebvrb9e.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20151212_125939_zpsqebvrb9e.jpg.html)
massive crack in my dizzy cap would explain the rough running.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20151212_122900_zpsclue6hks.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20151212_122900_zpsclue6hks.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160103_143502_zps32m9jenm.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160103_143502_zps32m9jenm.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160103_172129_zpsjsyoitir.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160103_172129_zpsjsyoitir.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160104_193611_zpsqrdvz4ea.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160104_193611_zpsqrdvz4ea.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160111_125613_zpstygsq2a0.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160111_125613_zpstygsq2a0.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160112_173940_zpszrtnbrox.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160112_173940_zpszrtnbrox.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160112_173954_zpseao25tco.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160112_173954_zpseao25tco.jpg.html)
DavidProehl
01-25-2016, 04:39 PM
Impressive is now the norm for this thread!
nkemp
06-10-2016, 09:59 PM
I feel like I've just binge watched and got to the season finale and now I have to wait to see what happens next. Inquiring minds want to know how the EFI conversion goes.
vwdmc16
06-10-2016, 10:47 PM
Thanks! It's been slow going and I hope it picks up when the car is drivable again.
Need to paint the frame and reassemble this weekend.
http://i31.photobucket.com/albums/c396/vwdmc16/Mobile%20Uploads/20160530_203505_zps3x9trg1x.jpg (http://s31.photobucket.com/user/vwdmc16/media/Mobile%20Uploads/20160530_203505_zps3x9trg1x.jpg.html)
And Im ready to assemble the engine with my new modified engine stand mount that can hold the upper crank case securely without the lower girdle
http://i31.photobucket.com/albums/c396/vwdmc16/Mobile%20Uploads/20160610_184303_zpstqr7qarq.jpg (http://s31.photobucket.com/user/vwdmc16/media/Mobile%20Uploads/20160610_184303_zpstqr7qarq.jpg.html)
vwdmc16
06-10-2016, 10:57 PM
Cylinder head resurfaced light as possible along with a valve grind.
http://i31.photobucket.com/albums/c396/vwdmc16/Mobile%20Uploads/20160610_184952_zpsrdfqkkkv.jpg (http://s31.photobucket.com/user/vwdmc16/media/Mobile%20Uploads/20160610_184952_zpsrdfqkkkv.jpg.html)
Didn't get far with the trans rebuild yet, didnt get my trans parts from DPI so I may hold off since the engine build has taken so long and I want the car done by the end of the month. Atleast The bell housing is super clean.
http://i31.photobucket.com/albums/c396/vwdmc16/Mobile%20Uploads/20160610_185005_zpswivia1bu.jpg (http://s31.photobucket.com/user/vwdmc16/media/Mobile%20Uploads/20160610_185005_zpswivia1bu.jpg.html)
Did get this nice box from DPI with most everything ill need.
http://i31.photobucket.com/albums/c396/vwdmc16/Mobile%20Uploads/20160610_185015_zpsg6gu8hoa.jpg (http://s31.photobucket.com/user/vwdmc16/media/Mobile%20Uploads/20160610_185015_zpsg6gu8hoa.jpg.html)
DavidProehl
06-11-2016, 12:32 PM
Glad the parts finally arrived! That engine is going to be a beaut!
DMC5180
06-11-2016, 12:56 PM
Was the bell housing hot tanked with the block? It looks fantastic. Since this is a rebuild, are reusing the stock Pistons or going High compression?
Dennis
vwdmc16
06-11-2016, 02:02 PM
The bell housing along with many engine parts were walnut shell blasted by myself. Hot tanks would damage aluminum.
Stock pistons, i still have to pass smog with this engine.
DMC5180
06-12-2016, 12:16 AM
Interesting, I could swear I've seen our engine blocks after some kind of cleaning process that made them bright and shiny like new engine clean. I swore it was a chemical cleaning process.
Dennis
Lwanmtr
08-06-2016, 01:42 AM
Great work so far.
vwdmc16
08-06-2016, 10:25 PM
Slow process lately due to a few reasons, heat, time and lack of parts. But there are no more excuses, so here is an update. Trying to upload these in chronological order.
Blasted pistons and rods:
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160425_190722_zpsxgwe9kpm.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160425_190722_zpsxgwe9kpm.jpg.html)
Made some cylinder holding tools for setting up piston ring gap, a few rings needed some filing. Measured all the new bearing tolerances which came in spec.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160616_213814_zpss2ny2oaf.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160616_213814_zpss2ny2oaf.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160616_213805_zpstiwv7x7v.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160616_213805_zpstiwv7x7v.jpg.html)
Primed and painted the upper an lower block.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160430_194412_zpsnd0skjma.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160430_194412_zpsnd0skjma.jpg.html)
More head cleaning and porting before they went to be resurfaced.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160430_194435_zpspwzq6fcx.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160430_194435_zpspwzq6fcx.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160430_194358_zps7uvoxctr.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160430_194358_zps7uvoxctr.jpg.html)
Time to measure the new cylinders for the proper shims, ended up clamping my dial indicator to my machinist straight edge to get that critical measurement.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160616_213828_zpsstgsasjl.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160616_213828_zpsstgsasjl.jpg.html)
I ended up needing the thickest shims, (yellow) to get to .006" deck height as shown. Sealed them with a little smear of Permatex.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160616_213908_zpsifse1idg.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160616_213908_zpsifse1idg.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160616_214046_zpsgb07e5j7.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160616_214046_zpsgb07e5j7.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160616_214106_zpstzilcp18.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160616_214106_zpstzilcp18.jpg.html)
Next the pistons and rods installed and torqued. lower girdle installed and sealed. Heads installed too after they were reassembled with my new cams.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160616_231114_zpsulv41e26.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160616_231114_zpsulv41e26.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160619_163110_zpsnrvkh1fu.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160619_163110_zpsnrvkh1fu.jpg.html)
Now for the worst part, setting the timing. This actually took me a few days of frustration to get right, and im still not 100% sure it's set correctly (although I have really good compression on every cylinder). I really want to punch the engineer that decided not to have some simple casting alignment marks put in so make it super easy to set the cams and crank to one position then put the chains on, instead you have to have the parts vaguely point at each other or at "12o'clock or 9'oclock" an you have to rotate the crank after doing one side. its so easy to get it off and cause damage. No other engine Ive ever worked on had such a convoluted and terribly vague set up instruction. Seriously not fun.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160619_212634_zpsws8nigxz.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160619_212634_zpsws8nigxz.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160723_140503_zpskttblbiv.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160723_140503_zpskttblbiv.jpg.html)
vwdmc16
08-06-2016, 10:49 PM
Moved on to easier things to relieve my frustration with the timing, Painted the frame. Still want a new frame one day, but this one is now stronger and prettier than it has been in many years.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160616_214154_zpscd3cafs9.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160616_214154_zpscd3cafs9.jpg.html)
Starting to re-do a lot of other parts I have in powdercoating. Finally got an oven and powdercoat gun set up at work, POWDER COAT ALL THE THINGS! Im actually kind of mad that I didnt do this sooner, it's not that expensive and it yields such a better finish than paint could, so if it is metal, and fits in my oven, it's getting coated. Reblasted the valve covers and coated in wrinkle black.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160722_185423_zpsf5xrnfzh.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160722_185423_zpsf5xrnfzh.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160722_190725_zpsksfhed9q.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160722_190725_zpsksfhed9q.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160726_195801_zpsb8abxczq.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160726_195801_zpsb8abxczq.jpg.html)
Got some silver for the intake and W pipe, probably going to re do my Kjet metering housing too.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160806_172406_zpszz4bbm9u.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160806_172406_zpszz4bbm9u.jpg.html)
Coated the water pump rear cover and thermostat cap too, all new water pump even though my old one has been doing well. Looks so nice!
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160802_122704_zpsojy6ycsl.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160802_122704_zpsojy6ycsl.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160802_204343_zpsmencoiqu.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160802_204343_zpsmencoiqu.jpg.html)
With all these nice parts the hardware looks pretty bad, so ive ordered about $50 of new engine hardware and brackets to replace the ugly ones and a few other remaining gaskets that I didnt get with my engine rebuild set.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160801_231112_zpsq5nu1tnk.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160801_231112_zpsq5nu1tnk.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160801_231057_zpsghauaehn.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160801_231057_zpsghauaehn.jpg.html)
Now its time to reinstall the suspension and under carriage parts before the engine and trans go back in. But that brings up the last big question, Should I rebuild the trans now? I was in quite a hurry to get this car back on the road, then the project because a back burner after I had to put alot into the V8olvo. Then it was my main focus again until I bought a old BMW E30 which kinda distracted me for a few months. Then I really wanted to get the car done by June 20th for my Summer road trip to visit family in Colorado, I had plenty of time and energy but all my parts didnt show up until a few days ago (A long story I wont get into). Now I want to get the car done before the 19th of August so I can drive it to the Historic by Rolex event at Laguna Seca raceway to check out that cool event. However Im not sure I can tear down, clean, and rebuild the transaxle as well as reassemble the whole car, Lots to do.....
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160501_160636_zpsersqhip2.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160501_160636_zpsersqhip2.jpg.html)
Lwanmtr
08-06-2016, 11:23 PM
Its lookin pretty good. Definately alotta work..and alot of stuff I wouldnt even begin to know how to do..like rebuilding an engine..hehe.
DMC5180
08-07-2016, 09:43 AM
How is the operation of the transmission? Leaks, grinding gears, or spongy second gear? Are you planning to powder coat the exterior?
Dennis
Very impressive work done so far :thumbup:
vwdmc16
08-07-2016, 02:58 PM
The trans needs some love, it doesn't leak much. Its appearance is pretty bad now, I painted it with POR15 silver that has begun to peel and turn green. It has quite a lot of trouble getting into 2nd gear due to partially sheared shift fork roll pins. It pops out of 5th alot on decel, but I think the detent is weak/jammed. The 2, 3 and 5 syncros dont feel that great either.
So yeah it needs a rebuild for sure. Im really leaning towards doing it now.
vwdmc16
08-16-2016, 01:35 AM
Trying to move real fast and get the car driving this week.
Fresh Fuel hoses from DMCMW, Had to get the inlet and return hoses made at a local hose shop, Not cheap but I need fire insurance.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160806_195441_zpsih2m0frj.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160806_195441_zpsih2m0frj.jpg.html)
Exhaust was cleaned up again and painted with super high temp paint and baked on, new studs, nuts and gaskets. Got to use the stock exhaust to pass smog...:angry4:
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160807_175426_zpspbrozs0j.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160807_175426_zpspbrozs0j.jpg.html)
Here is a view of the cleaned up exhaust and intake ports too. Anxious to feel the power difference
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160807_202604_zpsm5fzrcr2.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160807_202604_zpsm5fzrcr2.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160807_202629_zpsqsm21cks.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160807_202629_zpsqsm21cks.jpg.html)
Engine is now just waiting on the transmission to be done.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160807_230158_zpsr7o3pp4x.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160807_230158_zpsr7o3pp4x.jpg.html)
So lets start on the trans! This was more of a refresh than a proper rebuild, No budget for new forks, gears or syncros. Just fix the busted roll pins, clean it up and re seal.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160807_230041_zpsq8ay3e7j.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160807_230041_zpsq8ay3e7j.jpg.html)
Nose cone blasted and coated silver.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160810_184752_zpsoj4p6nw0.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160810_184752_zpsoj4p6nw0.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160810_193752_zpsogcartor.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160810_193752_zpsogcartor.jpg.html)
Nose cone parts coated gloss black.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160810_184810_zpsrpwarche.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160810_184810_zpsrpwarche.jpg.html)
Back at home, I got the case open. found the usual issues.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160810_222745_zps6x09lmy7.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160810_222745_zps6x09lmy7.jpg.html)
2nd gear shift fork roll pin completely sheared off, makes for a very spongy and tricky shift to 2nd
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160810_222622_zpsqrngmraz.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160810_222622_zpsqrngmraz.jpg.html)
Found a broken part of it and the rest is probably in this thick metal sludge that the internal magnet picked up. NASTY.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160810_222631_zpsdosxi0m9.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160810_222631_zpsdosxi0m9.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160810_223018_zpswp64zqbp.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160810_223018_zpswp64zqbp.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160810_222647_zpskcnrvbmk.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160810_222647_zpskcnrvbmk.jpg.html)
I ended up spending about 25hrs tearing down, cleaning and rebuilding the trans. most was from blasting off the old POR15 that I painted on years back. Before and after:
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160812_194843_zpsuqhkiogo.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160812_194843_zpsuqhkiogo.jpg.html)
Then the other side. all new hardware too!
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160813_135117_zpsgyn7cju7.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160813_135117_zpsgyn7cju7.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160813_143517_zpsjgbbjqcy.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160813_143517_zpsjgbbjqcy.jpg.html)
Now to re assemble, I decided to polish up the shift rods to make them a little smoother.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160814_113331_zpsjaagomwt.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160814_113331_zpsjaagomwt.jpg.html)
New Roll pins and double roll pins to prevent shearing again.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160814_124829_zps3nckaf5a.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160814_124829_zps3nckaf5a.jpg.html)
Next was another hard part, Replacing the input shaft coupler. I got one of the new improved couplers that was for sale here on the forums from Ed G. My old coupler did NOT want to give up. A few days of oil penetrate did nothing against the 35 years of being together. but with more oil and heat and very careful cutting I was successful. that new one was a tight fit too.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160814_134314_zpsx5aupr8k.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160814_134314_zpsx5aupr8k.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160814_140822_zpsvtlynxvz.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160814_140822_zpsvtlynxvz.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160814_141841_zpsrt8gqixh.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160814_141841_zpsrt8gqixh.jpg.html)
After setting the diff bearing loading, its all clean and ready to go together again, I tried out a different Anaerobic sealant from Wurth, hope it lasts, sorry for fuzzy picture.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160814_142420_zpsdsolbd1i.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160814_142420_zpsdsolbd1i.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160814_143634_zpsb7uu7pkx.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160814_143634_zpsb7uu7pkx.jpg.html)
New front and rear seals from DPI
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160814_173632_zpso2dq29i1.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160814_173632_zpso2dq29i1.jpg.html)
And BAM she's sexy again, too bad its hidden under the car. Also freshened up the clutch slave and hose, It has a new braided clutch line to join up to now
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160814_180535_zps45hxopps.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160814_180535_zps45hxopps.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160814_180545_zpsbj0u7pel.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160814_180545_zpsbj0u7pel.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160814_182218_zpsjlcfptxj.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160814_182218_zpsjlcfptxj.jpg.html)
Glad to see things coming back together! That transmission looks amazing. Better than brand new.
DMC5180
08-16-2016, 11:47 AM
Looks Great.
The only thing that stands out to me is that you only used a single 2nd gear Roll pin. DMCH supplies a second pin to drive inside the larger one just like the pin installed at the other end of the spring for added strength.
Dennis
jawn101
08-16-2016, 12:09 PM
Looking so good, Clint!! I really hope nothing leaks on all this great new coating :)
Looks Great.
The only thing that stands out to me is that you only used a single 2nd gear Roll pin. DMCH supplies a second pin to drive inside the larger one just like the pin installed at the other end of the spring for added strength.
Dennis
He said he double-pinned everything...
jawn101
08-16-2016, 12:11 PM
Also, I LOLd at the pic of you flipping the engine off. Reminds me of this one, which was of you working on my transmission :)
http://www.orangeoblivion.com/gallery/d/66925-2/DSCN3932.JPG
DMC5180
08-16-2016, 12:28 PM
Looking so good, Clint!! I really hope nothing leaks on all this great new coating :)
He said he double-pinned everything...
Going by the installed photo, 2 out of 3 pins are doubled. The important one looks to be a single, unless he took the photo before installing the second pin in that location.
Dennis
DMC5180
08-16-2016, 12:33 PM
Also, I LOLd at the pic of you flipping the engine off. Reminds me of this one, which was of you working on my transmission :)
http://www.orangeoblivion.com/gallery/d/66925-2/DSCN3932.JPG
BTDT! Those split plastic bushing are a bugger to get reinstalled. Probably easier if you remove the cross gate shaft completely though.
Dennis
vwdmc16
08-16-2016, 05:19 PM
Looks Great.
The only thing that stands out to me is that you only used a single 2nd gear Roll pin. DMCH supplies a second pin to drive inside the larger one just like the pin installed at the other end of the spring for added strength.
Dennis
Its in there, for some reason I took that picture first, all the other pins are doubled up too.
vwdmc16
08-16-2016, 05:22 PM
Also, I LOLd at the pic of you flipping the engine off. Reminds me of this one, which was of you working on my transmission :)
http://www.orangeoblivion.com/gallery/d/66925-2/DSCN3932.JPG
I recall that, I made a tool from a plastic panel pry tool that helps greatly by holding the spring to one side.
I also bought new bushings and boot for that shaft but ended up forgetting to install them since the old ones were in good shape.
vwdmc16
08-20-2016, 12:58 AM
Found a better picture of the new roll pins. Double pin is there.
DMC5180
08-20-2016, 01:21 AM
Found a better picture of the new roll pins. Double pin is there.
Whew !
Dennis
jawn101
08-20-2016, 01:39 AM
Found a better picture of the new roll pins. Double pin is there.
I never doubted you :) These other guys just don't know you well enough! :)
vwdmc16
08-26-2016, 07:58 PM
Pic of the tool i made from a plastic scraper to hold the trans shifter selector spring to one side.45955
vwdmc16
08-26-2016, 08:01 PM
Engine and trans installed hoping to fire up this weekend.
Lwanmtr
08-26-2016, 08:38 PM
The engine always looks like its on the floor when I see pics of them like that. Hope it fires up all nice for ya.
vwdmc16
11-06-2016, 01:23 AM
Time for another update. Car is all together and driving but the rebuild isnt really done as I have some significant issues still. Lets go back where we left off.
Rear main before and after:
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160103_172129_zpsjsyoitir.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160103_172129_zpsjsyoitir.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160820_191731_zpsclqeqsyw.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160820_191731_zpsclqeqsyw.jpg.html)
Engine ready to be connected to trans.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160807_230127_zpsud2zfewf.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160807_230127_zpsud2zfewf.jpg.html)
Newly blasted and clear powdercoated coolant pipes.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160810_224401_zpsyqnujhac.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160810_224401_zpsyqnujhac.jpg.html)
Dropped in and trans looking fine in its new clean home. coated fuel filter holds the new filter. Painted exhaust looks nice too. I did have a bit of a fight with the new DPI stainless clutch hose, the flare fitting at the master cylinder had a imperfect flare that would leak, I had to tighten the hell out of it to get the buble flare faces to mate fully. Then I had the same issue with the fittings at the transmission end. 2 hours or messing with that and I had a clutch again.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160820_211725_zpstdh4mdfv.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160820_211725_zpstdh4mdfv.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160820_211833_zps4ph08y59.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160820_211833_zps4ph08y59.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/1fda8a70-89a5-4f29-bc70-7f27e3017077_zpsl7tebmj2.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/1fda8a70-89a5-4f29-bc70-7f27e3017077_zpsl7tebmj2.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160828_144829_zpszwywvjir.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160828_144829_zpszwywvjir.jpg.html)
Finally all back together. Primed the fuel system after cranking for about 30 seconds to get good oil pressure and she started up nicely! Went back over all the connections and tightened up some fuel and coolant leaks. Held the revs at 2k for about 20 minutes to break in the cams, cooling system held the temp cool and steady.
After another full inspection for leaks or issues I took her around the block without the rear fascia, clutch felt great, trans shifted better than ever. However the car really lacked power, felt like maybe 60 to 70 hp max, something wasnt right. went over the timing and fuel CO adjustment, checked the plugs, nothing was out of order but the car had no kick to it, throttle response was lazy and dull.
GRRRR! so frustrating. Well I took it back into to my shop to dig in more, thats when I noticed a large amount of oil leaking from the bellhousing area after my 20 mile drive. WTF! I was certain the rear main was bad, and I was so careful about it too. Well no two ways about it, the trans must come out.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160905_151047_zpstxq3w2jn.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160905_151047_zpstxq3w2jn.jpg.html)
To make it easier, I whipped up this quick adaptor tool for the trans jack.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160905_182719_zpsid7dijzl.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160905_182719_zpsid7dijzl.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160905_151035_zpsc96qk5v4.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160905_151035_zpsc96qk5v4.jpg.html)
Lwanmtr
11-06-2016, 01:31 AM
Ouch..hope you get it sorted.
vwdmc16
11-06-2016, 01:45 AM
The heavy oil leakage was a light grey color so I was thinking engine oil as my RedLine trans fluid was well, Red. Bottom of trans and engine mounts were soaked. Removed the like new belhousing protection plate, what a pain. Not sure that is going back on...
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160905_151023_zps58npio86.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160905_151023_zps58npio86.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160905_151031_zpsvkzpjvji.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160905_151031_zpsvkzpjvji.jpg.html)
Got the trans out and the inner bellhouse is soaked too, but no big leak from the rear main!
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160905_155341_zpsnvsrkqnh.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160905_155341_zpsnvsrkqnh.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160905_155431_zpslwkgvsgt.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160905_155431_zpslwkgvsgt.jpg.html)
Hard to see in pictures but the bottom of the engine at the oil pan level was all wet, the engine mount area too. lots of oil on the engine side of the flywheel.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160905_155254_zpsvvcowryx.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160905_155254_zpsvvcowryx.jpg.html)
But where did it come from? Not the oil pan, that wouldnt explain the oil in the bellhousing, Look how dry this rear main is. its doing great!
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160905_155314_zps4icfop0z.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160905_155314_zps4icfop0z.jpg.html)
I concluded the oil had to be trans fluid, It was still full (of red fluid) so where is it leaking? So I decided to reassemble and go drive again for a short distance to get a better idea where it starts from. A quick 3 mile drive around the business park at my shop later and I put the car back on the rack, still dry! This was puzzling, it would not leak at idle or after a short drive, just long ones where it all gets hot. It had to be the input main shaft seal leaking when the trans got hot, the oil must be turning dark as its being flung through the clutch disk on its way to coat the bellhousing. Ugh that was a new clutch too.I knew the trans would have to come out and apart again.....
Since I had no parts to fix it I drove home, inspected it again to find the same huge oil mess again. And yes I know I didnt paint the bottom of my frame cradle, still planning on welding a 1/8" plate to cap over all that beat up metal so I can actually put some jack stands under it without smashing it up.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160905_193201_zps960rjitu.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160905_193201_zps960rjitu.jpg.html)
jawn101
11-06-2016, 10:46 AM
Bummer about the leak, still. Any chance it's clutch fluid? I guess you said it still felt tight though.
Still amazed how good it looks. Are you still going to be able to get it into town for next weekend?
vwdmc16
11-09-2016, 03:53 AM
Yes, I was sure it was not clutch/brake fluid since I also had that leak too. My rebuilt Slave cylinder is not entirely sealed. Still leaking a bit today, put it on the list...
Ill update more when I have time on my main computer but yes the trans leak has been fixed and the car will be going to see Grady and Nicholson this sunday. Driven if it passes smog, trailered if not.
opethmike
11-09-2016, 09:33 PM
Off-topc; do you still have your Esprit? How is that doing?
vwdmc16
11-10-2016, 02:18 PM
Ive never owned an Esprit.
opethmike
11-10-2016, 03:44 PM
Ive never owned an Esprit.
Had you confused with someone then, sorry.
vwdmc16
11-17-2016, 01:14 AM
Determined to get the refreshed trans sorted I ordered a new input shaft seal and output shaft roll pins. After a few days it arrived and I trailered the car back to my shop as to prevent more oil leakage and pulled the trans. It was a quick job all told, only about 3.5 hrs to remove the trans and old input shaft seal, then install the much tighter and more pliable new one in its place, re assemble the trans again with the Wurth Flange adhesive and using Wurth super Grey RTV on the bellhousing and tail cone flanges since the new DPI gaskets were now destroyed.
Pulling the old lip seal off the input shaft was not an issue but installing the fresh new seal without damaging it as I slipped it over the new and thicker than stock input coupler was going to be hard. I briefly thought about pulling the new coupler back off the main shaft but its pretty much a press fit where as the original coupler is not, so this wasnt really an option that wouldn't damage the key components to the trans, so my clever Idea was to roll a sleeve of clear plastic sheeting over the input shaft and coupler to funnel the new lip seal over the sharp corner of the coupler and its roll pin hole. It was the same idea of slipping that plastic sleeve over a cylinder head valve stem when installing new valve stem seals.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20161002_175659_zpsdynktrqe.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20161002_175659_zpsdynktrqe.jpg.html)
The offending seal on the left that I know I should have replaced in the first place....
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20161002_173934_zpsuaf9d3c9.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20161002_173934_zpsuaf9d3c9.jpg.html)
All back together and installed that night. Since then Im glad to report that the trans oil is staying inside as it should. However I do have clutch fluid seepage still after a long drive. time for a new clutch slave.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/IMG_20161007_131650_zpsuoxyq9pm.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/IMG_20161007_131650_zpsuoxyq9pm.jpg.html)
With one major issue fixed I turned back to my more worrisome fault, the low engine power. Another compression test was in order using a different gauge. Results were still disappointing: 90psi on the 4-6 cylinders and just 65psi on the 1-3 cylinders.
I decided to remove the muffler to gain access to the crank pulley to turn the engine over manually and investigate closer. With the spark plugs out and a light shining down into the cylinder you can just see the intake valve on the peak of its opening stroke. As I turned the engine over by hand I saw the piston was also rising back up as the intake valve was closing, this is not correct at all! how can the engine build compression if the intake is still open while the piston is on the compression stroke? The cam timing has to be retarded. So off came the timing cover while keeping the valve covers on.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160919_072550_zpsgrnklv7f.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160919_072550_zpsgrnklv7f.jpg.html)
As I stated before I had a really difficult time getting the cam timing set when assembling the engine, nothing quite lined up as the manual stated in its strange method. I found that I could remove the chain tensioner and the guide to give me just enough slack to allow me to slip the chain over one tooth at a time on the cam gear, Reinstall the guide and tensioner and move to the other chain. After a bit of experimenting I found the 1-3 bank could be advanced one tooth but the 4-6 bank could not without having piston to valve interference. It seems that the right hand cam was off one tooth the whole time.:bash: Before reinstalling the timing cover I performed another compression test with the engine spinning by starter.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20160919_072542_zpscdk3ypwi.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20160919_072542_zpscdk3ypwi.jpg.html)
BAM even compression on all 6 cylinders! Now strangely it was still just 95psi where a healthy engine should be at 140-160psi. Long story short I later found that even this, the second compression gauge I used was reading about 35% lower than actual. A third and know calibrated gauge later found that my engine makes 145psi which isnt bad for a stock compression engine that isnt fully broken in ( still wishing I sprung for high compression pistons..... So I put the cover back on and reinstalled the muffler, went for a drive; the engine had more power but if im honest, still didnt feel anywhere as peppy and strong as I was hoping, It actually didnt feel as strong as the engine was before the rebuild....with stock cams......and unported heads...... then again it's been what, nearly a year since I drove this car or any other Delorean. More tuning was in order but a trip to the dyno will be what really tells the power that it puts out, then the DMCH exhaust will go back on and hopefully wake it up. But I need to smog before that...more about that adventure next time.
Here is a quick video of the engine running without the timing cover, yes it made a bit of a mess.
https://youtu.be/GGVjJth9eeg
Delorean Industries
11-17-2016, 10:05 AM
I would have sent you another pair. That Wurth crap is worse than GM factory gray. Takes a jack hammer to get it apart.... I know it sucks that some gaskets such as trans matting surfaces are one time use....
vwdmc16
11-18-2016, 12:49 AM
Ive had great luck with the Wurth Grey RTV, I use it all the time on the BMW engines, never had them overly bond aluminum together, yes they require some effort to seperate but not too much that it becomes serviceable. I do think I will need to go back into the trans again in the future, still having 5th gear pop out of gear on me occasionally during decel, thinking the 5th gear fork may be bent.
DMC5180
11-18-2016, 01:09 AM
The 5 gear is all under the back cover. That's not major surgery like you just did. That's just removing the back cover while the transmission stays in the car.
Sent from my iPhone using Tapatalk
vwdmc16
11-18-2016, 03:38 AM
True, I might be able to change the fork in car.
Delorean Industries
11-18-2016, 09:19 AM
Want us to send over another pair of gaskets?
vwdmc16
11-18-2016, 04:13 PM
That would be fantastic Josh, thank you!
vwdmc16
11-27-2016, 06:31 PM
Now with the trans and engine mechanically sorted, I did some further tuning with the AFRs. Using my Innovate LM1 wideband dataloger I was able to moniter the fuel ratio during cruise and WOT.
http://static2.shopify.com/s/files/1/0023/1812/files/3723_small.jpg
The car was running a little lean, high 13's at full throttle, tuning the CO adjustment screw little by little I was able to get down to 12.8 at WOT and still hold 14.7 at cruise and idle. Perfect! but there was still no notable power increase, oh well, it was running very well and started better than ever.
While checking Craigslist regularly for Delorean items I found an ad for Delorean panels. They were painted a dark blue and looked a bit worn. The seller was a motorcycle guy and just wanted them gone, he was asking $600 for all four fenders plus T panel, lower engine lid and what appeared to be some Ford 5.0 parts that neither of us wanted. I set up a time and went to see them an hour and half away from Sacramento. Most of the panels had damage repair that was visible on the back side. But they werent thrashed and Im always looking for some stainless to practice repairs on. $300 later I piled them in my truck and headed home hoping it was worth it.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20161023_162236_zpstcilumey.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20161023_162236_zpstcilumey.jpg.html)
Soon began to strip them with aircraft paint stripper and a paint scraper. T panel first, showed no damage from the back side but it did have some light wrinkling and ripples.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/tpanel1_zpsy91269gk.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/tpanel1_zpsy91269gk.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/tpanel2_zpsf4mqvyoi.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/tpanel2_zpsf4mqvyoi.jpg.html)
Next the LFF, it had some dent puller holes welded up (stainless Tig welding atleast!) near the dents on the trailing edge where it meets up with the door, plus some other repairable dents on the leading edge. Overall pretty rough. Next I started the RR quarter, the only panel left with no visible damage on the backside. After another 2 hours of chemical stripping and scraping, then acetone to clean it up it looked like I had one undamaged panel, NICE! It wasnt even that badly sanded for the primer! Ill get to the other panels soon but they will be ugly ones too. More wall art! I just need a rear Fascia and a driver door to have a complete set of extra panels!
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/lff%20and%20lr_zpswhf2h7fm.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/lff%20and%20lr_zpswhf2h7fm.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20161127_121714_zpstvcsffw7.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20161127_121714_zpstvcsffw7.jpg.html)
This November Rob Grady and Chris Nicholson came to my area to service the NCDMC , I quickly jumped on the list to have some body work done by the best stainless guys there is! When my day came I trailered my car over to Wrench Works in Vacaville. My plans was to have the car regrained after 3 hours of dent repairs as I wasnt planning on dumping alot of money into the car after the engine and trans job became more expensive than planned.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20161113_115022_zpshs6yjkt1.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20161113_115022_zpshs6yjkt1.jpg.html)
Chris gave his once over and gave his thoughts on the damage, The car was quite bad, every panel needed hours of work, especially the doors but I didnt want to change out doors since they operated so well. He was confident that everything else could be fixed on the car even the gas flap hood could be saved.
"There there you poor beat little car, Im here to fix you up"
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20161113_113312_zpsejb6dycz.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20161113_113312_zpsejb6dycz.jpg.html)
vwdmc16
11-27-2016, 06:47 PM
Rob Grady and I went over the large estimate to determine the best option for me, To repair the entire car was going to be 28.5 hrs of Nicholson hammering and flap sanding, regain included. That exceeded the purchase cost of the car for me and out of my budget!
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20161113_120523_zpsahj3sojs.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20161113_120523_zpsahj3sojs.jpg.html)
I decided the worst damage had to be dealt with so the LFF and hood were priority #1. I still cant believe the results! He did all this without removing the LFF and by drilling just tiny holes under the trunk rubber seal to push that long dent out, you open the trunk and you cant even tell!
BEFORE
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/hoodllffbefore_zps7fjgnzvv.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/hoodllffbefore_zps7fjgnzvv.jpg.html)
AFTER!
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/hoodlffafter_zpssfxi51xl.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/hoodlffafter_zpssfxi51xl.jpg.html)
Next the passenger door dent on the b pillar was next as that was the ugliest part of the car, it was a very strange dent that someone had attempted to repair before. I had written that off to be repaired only by cutting the metal skin off and welding on a donor piece that I had, But somehow Chris was able to make that damage vanish! it still makes me speechless!
BEFORE
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/rdoorbefore_zpsqoforswf.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/rdoorbefore_zpsqoforswf.jpg.html)
AFTER
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/rightdoorafter_zpssymqh0fs.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/rightdoorafter_zpssymqh0fs.jpg.html)
In the end I decided to alot more than 3hrs of repairs, (the hood was than much alone and well worth it) and repair everything but the Drivers door. My plan is to replace that door next year with a good used one since that is cheaper than fixing this one that has bad glass and seals anyway. I could have posted pages of before and afters on my car alone, but here is another, this one on the LR quarter
BEFORE
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/quarterbefore_zpsslzqczs4.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/quarterbefore_zpsslzqczs4.jpg.html)
AFTER
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/quarterafter_zpsvwgzsf13.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/quarterafter_zpsvwgzsf13.jpg.html)
If you are on Facebook you can see this video of my hood being repaired, incredible work Mr. Nicholson! thanks so much,
https://www.facebook.com/jordanlivingston82/videos/10210139129808294/
Lwanmtr
11-27-2016, 06:50 PM
Definately alotta work..and looking good
sdg3205
11-28-2016, 03:06 AM
I asked Chris if he was going to be in the PNW any time soon. I'm sure if he spent a week in Seattle at DMCNW he could make a fortune tweaking the dents out of our cars. Hell I'd drive down there to get mine done in a heart beat.
Lwanmtr
11-28-2016, 03:29 AM
Lol..would have to be a house call, since mine's pretty much immobile for a while.
vwdmc16
04-02-2017, 07:16 PM
It's a new year, time for a new update. Progress is again slow but things are happening. it also seems that again this year wont be fully focused on the Delorean... more unfortunate events have occurred. My other main car project got a powerful set back.
One early January damp morning on the way to the shop for some more upgrades A Ford van pulled out of a parking lot into my path and I had no time to stop before we collided at about 40mph. My mighty V8 Volvo Fyord was totaled, I walked away with whiplash but the car is too far gone.
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/20170118_081936_zpsfnnjskqg.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/20170118_081936_zpsfnnjskqg.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/20170118_081835_zpsagiqqdit.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/20170118_081835_zpsagiqqdit.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/20170119_192934%201_zpsdmhovks4.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/20170119_192934%201_zpsdmhovks4.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/20170213_200415_zpswypp0f7f.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/20170213_200415_zpswypp0f7f.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/my%20v8olvo/20170213_200422_zpshmhi3gcy.jpg (http://s31.photobucket.com/user/vwdmc16/media/my%20v8olvo/20170213_200422_zpshmhi3gcy.jpg.html)
So that was a huge and painful upset however the planets aligned and the Swedish viking gods looks fondly on me as an identical '75 Volvo 242 popped on craigslist just then in the next town over. For $1500 i could have another identical donor shell to rebuild my car, Some how this seemed reasonable so I bought it and have begun the V8 swap. this car will require more cosmetic work than the first car, but it was actually a straighter shell. So I present project Fyord 2.0! This car was made a month later, and is 1230 Vin #s off of my crashed one and mostly the same condition that I started off with all those years ago. Atleast this time I have a donor car and I know what Im doing.....
http://i31.photobucket.com/albums/c396/vwdmc16/fyord2/20170122_121613_zpsqhxvzzit.jpg (http://s31.photobucket.com/user/vwdmc16/media/fyord2/20170122_121613_zpsqhxvzzit.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/fyord2/20170122_121624_zps8ofd7uop.jpg (http://s31.photobucket.com/user/vwdmc16/media/fyord2/20170122_121624_zps8ofd7uop.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/fyord2/20170212_124922_zpsshq4wxaa.jpg (http://s31.photobucket.com/user/vwdmc16/media/fyord2/20170212_124922_zpsshq4wxaa.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/fyord2/20170212_124938_zps1r0yxxdu.jpg (http://s31.photobucket.com/user/vwdmc16/media/fyord2/20170212_124938_zps1r0yxxdu.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/fyord2/20170401_195906_zpschardee0.jpg (http://s31.photobucket.com/user/vwdmc16/media/fyord2/20170401_195906_zpschardee0.jpg.html)
So this may take up most of the first half of this year's spare time, I also bought a new daily Driver: a clean 2001 330Ci, I doubt I can leave that alone either
http://i31.photobucket.com/albums/c396/vwdmc16/other/20170301_121131_zpsa9yoztzb.jpg (http://s31.photobucket.com/user/vwdmc16/media/other/20170301_121131_zpsa9yoztzb.jpg.html)
Meanwhile I have done some more work on the Craigslist panels, My first attempt at filling the antennae hole, Im probably going to drill it out and try again with some thinner diameter Stainless filler rod, I was having trouble getting enough heat to melt the rod while not destroying the base metal, its all just practice and getting the right set up.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170201_131031_zps63iuzuz3.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170201_131031_zps63iuzuz3.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170201_181947_zpsw3hziiwt.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170201_181947_zpsw3hziiwt.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170201_181951_zps29hmaffl.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170201_181951_zps29hmaffl.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170201_183022_zpscmwjr9zr.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170201_183022_zpscmwjr9zr.jpg.html)
First Job of the year on my car was to remove the Pedal box for new bushings, paint, and to replace the broken pedal return springs, plus I start another neat upgrade to the steering column. stay tuned!
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/columnout_zpsmlgjbise.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/columnout_zpsmlgjbise.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/column_zpsmz6remqu.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/column_zpsmz6remqu.jpg.html)
jawn101
04-02-2017, 08:09 PM
Still hurts to see those pictures of the Fjord... but I'm glad the new one is coming along well.
And now you've got me interested.... what's your plan for the steering column??
vwdmc16
05-07-2017, 06:12 PM
Time for another update. Back in January I pulled out the entire pedal assembly to rebuild it, new bushings, replacement springs for the broken one and a good cleaning. Also reset the firewall steering bushing in the correct direction and tightened up the play in the steering column shaft where is collapses. What a huge chore that turned into, but it was worth it, The pedals feel much tighter and responsive and now I have just about zero steering play.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170101_225239_zps3ylnuhts.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170101_225239_zps3ylnuhts.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170101_225305_zpsnjjznwg8.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170101_225305_zpsnjjznwg8.jpg.html)
Another quick Project I did was whip up a "front strut" brace. Now ive been very weary of the benefits of such things on these cars, for one there are no struts like McPherson suspension cars that could use the reinforcement. Two, there is a decent crossmember right in front of the fuel tank and directly below this brace, Three, the length that this brace has to go up to fit in the trunk creates alot of leverage arm length that works to weaken its design and negating the purpose of it to enforce the transverse loads in the chassis.
But I had some spare time one night, some 1.25" tubing and thought why not test it. This is what I cam up with, I made it simple as possible, short and straight too in order to maximize its stregth.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20161216_192344_zpsgajaxr5r.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20161216_192344_zpsgajaxr5r.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20161216_192359_zpsdocsou4k.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20161216_192359_zpsdocsou4k.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20161216_192715_zpsmzoyb7je.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20161216_192715_zpsmzoyb7je.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20161216_192706_zpsflmyhkp5.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20161216_192706_zpsflmyhkp5.jpg.html)
My impressions: Like everyone that has installed one of these, I also lack some hard scientific way of measuring any increase in torsional strength gained by this, I would need some million dollar frame torsional strength rig that OEM companies may use. That would be a very interesting test to see just how weak our cars are compared to a modern car. So really it comes down to human judgement. I will note that the front of my car no longer creaks as I enter my driveway at an angle without this braces, and there does seem to be a hint of increased stiffness in the front end's mannerisms.
Does it do anything? It has decreased some front end noise for sure.
Is it worth it? Borderline yes with the increased difficulty to remove the spare tire and get to the Brake Master.
Conclusion: I want to do more testing with it on vs off. Also build another version that has a freely collapsing center section that I can use to measure compression and expansion amounts during regular and heavy cornering. (This may be a while as its low on priority in my life currently)
Lwanmtr
05-07-2017, 06:44 PM
Nice work.
I saw a brace up at DMCNW that is curved and looks like it goes around the spare and that..but didnt ask about it, as I have enough I still need to do on mine before that kinda thing.
vwdmc16
05-07-2017, 08:01 PM
Bam second update, Im spoiling you guys.
This is the beginning of my Cruise control retrofit. As some of you know i work at a BMW shop and have kinda become a bmw guy too. I was really impressed with how well the BMW E30 cruise control set up works for a 30 year old system. I also like the way the handle looked and felt, very high quality. The entire cruise system is actually self contained, fully electric, compact and I thought it wouldn't be a terrible project to retrofit into my Delorean plus it almost looks OEM doesnt it? I wouldnt stand to put a modern or vintage aftermarket cruise system in as they look very tacky. So here it goes:
Complete E30 cruise system: stalk, actuator, wiring, control unit, just needs power, ground, brake/clutch switch and a speed signal.
http://designbolt.com/thestore/e30earlycruise/IMG_8282.jpg
First off i want to make sure I could mount the control stalk onto the Delorean column, so I went to the local junk yard and got all the parts I needed from a '90 BMW 325i. I found it would fit nicely under the wiper stalk with a simple tab.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170108_170529_zpsrgnmauki.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170108_170529_zpsrgnmauki.jpg.html)
Template for stainless tab I welded on the DMC column
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170108_170538_zpsshnpgtx8.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170108_170538_zpsshnpgtx8.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170108_172716_zpsh5lgwcqk.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170108_172716_zpsh5lgwcqk.jpg.html)
Tig welded on
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170108_172728_zpsvys9fse0.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170108_172728_zpsvys9fse0.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170108_173536_zpszhghbfyf.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170108_173536_zpszhghbfyf.jpg.html)
Now there are two arm lengths made for the BMWs, Air bag and non air bag. Neither style matched the Delorean style so I would have to cut up, shorten and re design the arm which is just a 6mm thick solid steel rod. So more cutting and welding
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170108_175018_zpsfvauv9q5.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170108_175018_zpsfvauv9q5.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170108_181842_zps0flwvyg0.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170108_181842_zps0flwvyg0.jpg.html)
1" section removed and the rod all sanded smooth
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170108_180246_zpscff3732i.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170108_180246_zpscff3732i.jpg.html)
looked to be a good shape now
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170108_184314_zpscg3njzxp.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170108_184314_zpscg3njzxp.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170108_184346_zpswexnq1l4.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170108_184346_zpswexnq1l4.jpg.html)
Now to make it look bettter, I tried some heat shrink
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170108_183735_zpsgip3sqol.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170108_183735_zpsgip3sqol.jpg.html)
However it did not come out nicely so simply black paint would be the end method
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170108_183927_zpsv2fkzy8s.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170108_183927_zpsv2fkzy8s.jpg.html)
Now to make the column cover work, preferably with minimal cutting
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170108_184828_zpsarhhbtwx.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170108_184828_zpsarhhbtwx.jpg.html)
And assembled, fits in very nice and tigthly
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170108_203741_zpsgedokp0l.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170108_203741_zpsgedokp0l.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170108_203721_zpsdk12etfv.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170108_203721_zpsdk12etfv.jpg.html)
Now to test leg room, im 6'4" so this is important, while it does work and I was happy with it at first, ive decided to go back and change the angle again to raise it up about an inch, this would mean the two arms will hit if you engage the wiper demist and raise cruise stalk at the same time but that isnt really a real world problem that should happen.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170108_211512_zps0i0gfwho.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170108_211512_zps0i0gfwho.jpg.html)
Currently this is all I have installed now, the control unit and switches should be pretty simple to mount under the dash, the actuator will need to be put in the rear pontoons and possibly a custom cable made to go to the throttle spool. I entertained the idea of putting the actuator under the dash too and having it pull on the gas pedal, this would negate the need to extend the 7 wire harness all the way to the rear of the car but I have doubts the actuator is strong enough to pull the DMC throttle cable from up front as its much heavier than the BMW throttle. That could cause issues. As for the speed signal, I intend on replacing the Lambda box with an inline VSS box like the DMCEU power steering kit uses.
Lwanmtr
05-07-2017, 08:20 PM
Very clever work there. Definately something I would never think about doing, since I have zero fab skills in that area...lol
vwdmc16
07-23-2017, 11:12 PM
I have been posting about my front brake modifications in the MX5 vented front brake thread but ill also post here for posterity.
The idea is to have vented front brakes that are:
1. less prone to fade as stock
2. Reasonably priced to convert
3. Easy to service/rebuild
4. Low cost parts and Readily available most places in the world.
5. Greater selection of brake pad compounds
6. 100% bolt on and reversible
Josh S in Canada is the real worker in making this possible, he CAD'd up these brackets and had them laser cut, they fit really well and with a few more parts it was ready to test. The basic but key parts:
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170502_072627_zps04xzn5p0.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170502_072627_zps04xzn5p0.jpg.html)
One OEM part can be reused with simple machining unless we created a scratch replacement:
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170430_144541_zps9pzpcmia.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170430_144541_zps9pzpcmia.jpg.html)
Spindle spacer is cut down a bit to allow room for the larger and improved wheel hub, 2000 Ford Escort rear hub. Replacement spacers are availble and cheap from DMCH.
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170430_144107_zpsvhgstsju.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170430_144107_zpsvhgstsju.jpg.html)
Some good used calipers were sourced, cleaned up and rebuilt with the easy to get and very low cost rebuild kits, new and Reman calipers are still available too and much cheaper than stock DMC calipers:
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170428_172737_zpsgfmsimyg.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170428_172737_zpsgfmsimyg.jpg.html)
Caliper, bracket and new hub installed, With some trimming the factory dust shield can also be installed but I opted not to during this testing phase:
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170506_190745_zpse73tnv3l.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170506_190745_zpse73tnv3l.jpg.html)
Fully assembled and plumbed with a easy to get universal 18" stainless -4 AN brake hose
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170502_230940_zps2a5gtesb.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170502_230940_zps2a5gtesb.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170502_230932_zpsge5lml5s.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170502_230932_zpsge5lml5s.jpg.html)
Plenty of room inside the stock 14" wheels
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170429_120130_zpschujhxcl.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170429_120130_zpschujhxcl.jpg.html)
vwdmc16
07-23-2017, 11:57 PM
Also here is a quick angle drive dust cap I made to allow the brake conversion to still work the speedo, A nice 3D printed one would be more slick.
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170508_183737_zpshstb2dgr.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170508_183737_zpshstb2dgr.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170508_183850_zpsxcdw6q6p.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170508_183850_zpsxcdw6q6p.jpg.html)
Now with the ability to easily attach other brake options on my car I jumped at the chance to try out this really nice aftermarket brake kit from Stoptech. This is their just released big brake kit made for 1990-2001 Miata and designed to fit under most 15" wheels or larger. I got a great deal on this kit as a local Miata shop I work with is a dealer for them now. Since it is bolt on for Miatas, its bolt on for me too!
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170524_134423_zpsz59hdaan.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170524_134423_zpsz59hdaan.jpg.html)
A few comparisons:
Stock DMC to ST ( you can see Ive been getting my stock brakes hot)
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170525_072436_zps77cihdws.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170525_072436_zps77cihdws.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170525_072507_zpsffo3qmxt.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170525_072507_zpsffo3qmxt.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170525_072703_zps4hoc80bi.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170525_072703_zps4hoc80bi.jpg.html)
mx5 1.8 stock vs ST vs DMC stock
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170525_210813_zpstlpdtaxp.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170525_210813_zpstlpdtaxp.jpg.html)
The big draw back (for some people) is the ST kit wont fit in the 14" delorean wheel.
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170525_210302_zpsealdhg72.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170525_210302_zpsealdhg72.jpg.html)
Plenty of room in a Delorean rear 15" wheel, which means I kinda want to go bigger already!
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170525_210135_zpszjbq373d.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170525_210135_zpszjbq373d.jpg.html)
With Josh S' adaptor kit they literally bolted right on, could even use the same universal brake hose although another 2" would be nice.
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170525_205951_zps0unqxpc9.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170525_205951_zps0unqxpc9.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170525_205937_zpstyoyjfdf.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170525_205937_zpstyoyjfdf.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170525_210015_zpse0yv7anj.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170525_210015_zpse0yv7anj.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170525_210024_zpsiudvocm1.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170525_210024_zpsiudvocm1.jpg.html)
So now I need another set of 15" wheels to get on the road with, wrong color but I was going to re coat all my rims anyways.
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170701_173059_zps6nxfaqbg.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170701_173059_zps6nxfaqbg.jpg.html)
A pair of 205/50R15s are very close to the stock 14" tire size in height so the speedometer stays very accurate ( 2mph fast when compared to a phone based GPS!) but having that extra 10mm of rubber up front on sticker and better tires really does improve the cars stability.
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/20170703_192459_zps2niqo2hk.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/20170703_192459_zps2niqo2hk.jpg.html)
Quick preview of what it will look like after some expensive re coating.
http://i31.photobucket.com/albums/c396/vwdmc16/dmc%20brake%20upgrades/received_1743069225706583_zpslq3t8bue.png (http://s31.photobucket.com/user/vwdmc16/media/dmc%20brake%20upgrades/received_1743069225706583_zpslq3t8bue.png.html)
DMC5180
07-24-2017, 08:15 AM
How much further does the wheel / tire stick out of the wheel opening? How close is the tire to contacting the front of the wheel opening when the tires are turned inward with a load in the trunk? How close is the possible contact with the ARB at full steering stop.
Sent from my iPhone using Tapatalk
vwdmc16
09-17-2017, 05:18 PM
How much further does the wheel / tire stick out of the wheel opening? How close is the tire to contacting the front of the wheel opening when the tires are turned inward with a load in the trunk? How close is the possible contact with the ARB at full steering stop.
Sorry for the long delay.
Short answer is they dont stick out too much but they are much larger!
Here is the width from the front, yes they contact the front of the fender arch/ front lip with mild steering input. The wheels also rub on the swaybar at full lock but so did my stock 14" wheels, Remember I have a Mazda MX5 steering rack that gave me more steering angle since its has more travel than the DMC rack.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170702_212200_zpsfmaikwso.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170702_212200_zpsfmaikwso.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170702_205852_zpslitk3x7r.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170702_205852_zpslitk3x7r.jpg.html)
Note they are still fully covered by the fender arch and when the suspension compresses it goes in father due to our natural camber gain of unequal length control arms.
Here is a more head on picture
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170702_205912_zpshzlzb7mb.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170702_205912_zpshzlzb7mb.jpg.html)
Since the rubbing on the leading edge of the fender is not acceptable I took the hub design apart again and removed the 10mm spacers that were welded onto the Shattenkirk brake adapter brackets and I cut the wheel bearing- hub spacers down the same amount. This pulled the front wheel track inboard 20mm over all and has stopped the rubbing, the front track is still wider than stock at this point too. I think pulling it in helped improve the look of the wheel fitment, I prefer them to be sucked in a little not " hella flush" but not like a heavily Narrowed beam on an aircooled VW. one drawback is the Ive lost a bit more of my turning radius, however with my MX5 rack its its still TIGHTER than stock.
I also have re machined the flange on the '95 Civic lug nuts ive been using, they now have the proper flat taper. This was easy to do on my benchtop lathe in 10 minutes for all 16, they are still deep enough that the stud does not bottom out and crack the cap. Solid lug nuts at last!
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170702_202000_zpspaarppej.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170702_202000_zpspaarppej.jpg.html)
vwdmc16
09-17-2017, 05:34 PM
Found a picture of the newly narrowed front end, its under a bit more compression than ride height, hence the extra camber. I also had to deepen my test angle drive /wheel centering cap. Need to 3d print a nice one soon.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170809_001153_zpsx61f6pwu.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170809_001153_zpsx61f6pwu.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170811_220823_zpskwymuz1a.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170811_220823_zpskwymuz1a.jpg.html)
Other projects:
Rebuild the shifter mechanism, full tear down, filed smooth a few notch areas, sand basted, powder coated, reassembled and wow it feels much nicer. some how this has fixed the issue of 5th gear randomly popping out of gear on the highway! I still need to replace the Crossgate cable as mine is extremely stiff and corroded, making the shifter very stiff left to right. Just another $200..... and Yes I wish I could get the DPI stainless shifter lever, maybe in a few more years.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170724_173403_zpsae67s4f8.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170724_173403_zpsae67s4f8.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170724_185200_zps0g3uvj0c.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170724_185200_zps0g3uvj0c.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170724_191410_zpsjvtzsaui.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170724_191410_zpsjvtzsaui.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170730_145428_zpst8epbx55.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170730_145428_zpst8epbx55.jpg.html)\
Also finally stripped down and powder coated my LCAs, new bushings which is what it really really needed.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170822_211352_zpswrwwtqop.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170822_211352_zpswrwwtqop.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170822_211343_zpsc9u0z0ky.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170822_211343_zpsc9u0z0ky.jpg.html)
Amazing work as usual Clint!
Lwanmtr
09-24-2017, 03:00 AM
Very nice...wanna do mine? :)
DavidProehl
09-24-2017, 09:13 AM
So nice!
vwdmc16
01-10-2018, 11:59 PM
Happy new year everyone! :flamed:
It was only August of last year, I just finished one last road trip: a solo trip to Reno, NV for Hot August Nights; and I declared that I was limiting myself from buying anything else on my Delorean for the year. I was already over budget.....but the car and my will broke down and couldnt stop myself from another expensive order to improve me car.
I heard many good things about the new Delorean vendor called Deloreango.com and I had a shopping list that they had great deals on. I really wanted a new shifter cable to round out my shifter rebuild since I knew the original cable still in the car was very worn and exceedingly stiff. That was the part I really wanted but I could really use new Ball joints and I had a few cooling parts that I needed after another incident. On a late night test drive in November and my Otterstat decided to blow out on a freeway on ramp. I did touch it the day before but I didnt think I disturbed it that much, Plus it was facing downward ( to avoid bubbles) and that made it rather close to the DMCH exhaust. After a long night with duct tape and some water I borrowed from some neighborhood water spigots, I was able to limp the 3 miles home on surface streets without overheating.
I also didnt trust my water tank so a new one was ordered as well as some fresh ball joints for the LCAs.
In with the new
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20171125_110817_zpsjwb5onmm.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20171125_110817_zpsjwb5onmm.jpg.html)
Out with the old!
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20171205_191343_zpsm0m3git7.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20171205_191343_zpsm0m3git7.jpg.html)
New vs old cable: shifter feels better and lighter but honestly not as light as I hoped.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20171205_191330_zpssawmcjkk.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20171205_191330_zpssawmcjkk.jpg.html)
Much better thread in design fan switch:
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20171206_180623_zpssayxiw3c.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20171206_180623_zpssayxiw3c.jpg.html)
Rip that front end apart again! I had a bit of play in the passenger lower ball joint. new one is much tighter and pressed in nice and tight too!
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20171207_192010_zpsnt7ia7bn.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20171207_192010_zpsnt7ia7bn.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20171207_195947_zpsw0whosvv.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20171207_195947_zpsw0whosvv.jpg.html)
Also painted the front end finally.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20170914_195131_zpsnxcry81v.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20170914_195131_zpsnxcry81v.jpg.html)
The rear also received some attention, New lower bolts to replace the tired old ones and I trimmed the lower bushing eyelet of the Bmw e32 cross reference shocks. The lower bushing is huge compared to any other shock set up available for Deloreans, and unfortunately they were gouging out the inner sidewall of my new BFG tires on hard turns. Still looking to try different shocks in this new year.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20171206_191842_zpssyaqcwbu.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20171206_191842_zpssyaqcwbu.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20171206_192427_zpsxxginnb3.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20171206_192427_zpsxxginnb3.jpg.html)
opethmike
01-11-2018, 12:16 AM
I've had mine blow out as well. Mine was zip tied in place, so it wasn't catastrophic, but it sure as hell wasn't good. I'll have to get one of those pipes well.
Lwanmtr
01-11-2018, 01:20 AM
Yaay, new parts. Looking good. my bottle is on my list, but pretty far down on the priority right now.
vwdmc16
04-29-2018, 12:52 AM
Another update, the car has been sitting most of this time but ive been busy. Found a 85 volvo 760 at the local wreckers, looks like overheating finally did it in. I wanted to get a spare set of heads and cams to experiment with but they were far too rusted.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180103_144422_zpswyttd1m0.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180103_144422_zpswyttd1m0.jpg.html)
I did grab the injectors, WUR, fuel dist, warm up switch, and cold start to clean up and use as spares since this stuff is only getting rarer. Ill send the injectors off to be cleaned and balanced. I also grabbed the different W pipe and throttle linkage as it should allow my BMW cruise control to be integrated easier.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180103_152407_zps9amegttt.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180103_152407_zps9amegttt.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180103_154404_zpsfrnpr2dl.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180103_154404_zpsfrnpr2dl.jpg.html)
fuel dist cleaned up well.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180104_191424_zpshedr74ty.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180104_191424_zpshedr74ty.jpg.html)
a Side project to rebuild some stock LCAs, reinforce, weld powdercoat and install new bushings and balljoints, these are set up for coil overs.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180117_141544_zpsa4vlwohj.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180117_141544_zpsa4vlwohj.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180123_192459_zpsoozytawd.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180123_192459_zpsoozytawd.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180125_190259_zpsaruhnbfj.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180125_190259_zpsaruhnbfj.jpg.html)
Meanwhile back on my car, I stripped the engine back down to a short block to remove the cams, my waterpump inlet hose was leaking into the valley too, more to clean.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180225_122843_zps0kwrxhpt.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180225_122843_zps0kwrxhpt.jpg.html)
Long story short the cams I bought when I rebuilt this engine in 2016 were not ground correctly, the engine made less power than stock. It sounded mean but had no bite, it also had very little engine vacuum, 12-14"hg so the brakes didnt even work well. So back to stock cams and maybe ill start up my 3.0 monster engine to satisfy my horsepower needs or go in another direction. I did not take any good pictures since nothing was really new and I was kind of upset throughout this process of trying to figure out my cams.
While reassembling I cracked the water pump rear cover.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180414_210853_zps1sltxopr.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180414_210853_zps1sltxopr.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180414_210859_zpsrgmsgbx8.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180414_210859_zpsrgmsgbx8.jpg.html)
So a quick TIG weld and its back in business, all because I wanted to change the color of the yellow W/P pulley to black.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180414_214841_zpsxxrhy374.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180414_214841_zpsxxrhy374.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180414_215241_zpsoncpwdk4.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180414_215241_zpsoncpwdk4.jpg.html)
Also re routed the engine wire harness, replaced some wires, removed others, shortened a bunch of wires that were routed in a poor way. All the main power cables stay on the left side of the engine bay and follow the frame cradle to the starter instead of going through the engine where it could be damaged.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180415_150831_zpsmzx63qxq.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180415_150831_zpsmzx63qxq.jpg.html)
Finally reassembled after many long hours, and fixing more faults including a bent intake valve on cyl # 4 after the head came back from a cam shop.
I also added some gold heat reflective tape on the frame and heat shields, yet another experiment, trying to lower engine bay temps and save the frame paint from the hot headers.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/received_1890533087657537_zpsslcabjan.jpeg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/received_1890533087657537_zpsslcabjan.jpeg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180415_213406_zps8so4su7a.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180415_213406_zps8so4su7a.jpg.html)
Finally running.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180416_192234_zpsciddsrdj.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180416_192234_zpsciddsrdj.jpg.html)
Tried another product to help save my crumpling rear bumper foam, some thick coats of this spray able rubber sealer, works well.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180417_191509_zpshpd9bwrm.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180417_191509_zpshpd9bwrm.jpg.html)
My test drive still yielded a bad alternator so time for another 1993 Saturn SL1 unit, plenty of voltage again, plus this one is much quieter than the old that always whined.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180419_182457_zps52ueka5d.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180419_182457_zps52ueka5d.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180419_182613_zpsjpqeiik7.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180419_182613_zpsjpqeiik7.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180419_182544_zps72im0gyi.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180419_182544_zps72im0gyi.jpg.html)
In conclusion, im glad the car is back together but very disappointed with how it drives, and the engine feels boring and stock again, since it is. I may need to re-evaluate how I will proceed since I have not been happy with most of my modifications the last two years. ive done alot of work and spent alot of money but I dont feel like it was worth it.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180419_183946_zpsqnwgubp3.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180419_183946_zpsqnwgubp3.jpg.html)
Lwanmtr
04-29-2018, 01:20 AM
Hehe..I hadnt though of flex seal...I used bedliner stuff that came in a rattle can.
Chris Burns
04-29-2018, 02:20 AM
This car has come a LONG way from where it was in 2009. I would be proud of that at least:race:
Granted it's no hot rod, but it's roadworthy and driveable and that's more important!!
MikeWard
04-29-2018, 02:00 PM
What are the part numbers from the Volvo CPR / Fuel Distributor / Ignition Distributor and Air metering unit? If they are the same as we have here in the UK then you could transplant those parts onto the D engine for a little extra power.
jawn101
04-29-2018, 02:16 PM
And it even runs well enough to make it through a whole parade! That’s a punishing afternoon for even the best cars - so it’s definitely something to be proud of!
My muffler heat shield is peeling apart (new-ish DMCH one) and it might be time to take it down and put some of that heat reflective tape on it. Does it come in a silver tone?
vwdmc16
04-30-2018, 05:19 PM
What are the part numbers from the Volvo CPR / Fuel Distributor / Ignition Distributor and Air metering unit? If they are the same as we have here in the UK then you could transplant those parts onto the D engine for a little extra power.
Is that a proven swap? I dont see how a different set of injectors, CPR or meter would gain power over the US DMC parts if both were tuned to maximum efficiency. A larger injector won't make more power if there isnt more air to go with it.
Ill definitely try all the parts to see if they work well atleast.
Injectors off to be cleaned and balanced this week.
I do know the distributor has a more aggressive curve, and I have installed a volvo dizzy years ago after my old one died, there was a subtle improvement.
Jon, yes there is silver tape to do the same job if the gold is too gawdy for you.
jawn101
04-30-2018, 06:03 PM
Jon, yes there is silver tape to do the same job if the gold is too gawdy for you.
Nice! Where do I find it? Only available at Wolff Auto or is it a Summit Racing special too?
vwdmc16
04-30-2018, 11:48 PM
The 1985 volvo parts are:
CPR: 0 438 140 128
Meter: 0 438 100 105
Injectors: 0 437 502 022
US DMC parts :
CPR: 0 438 140 066
Meter: 0 438 100 109
Injectors : I have to remove to see...
vwdmc16
05-01-2018, 01:37 AM
Nice! Where do I find it? Only available at Wolff Auto or is it a Summit Racing special too?
Yeah search Summit. Heat barrier, heat wrap, heat shield tape.
MikeWard
05-03-2018, 05:12 PM
Is that a proven swap? A larger injector won't make more power if there isnt more air to go with it.
I do know the distributor has a more aggressive curve, and I have installed a volvo dizzy years ago after my old one died, there was a subtle improvement.
It is in the UK, have a read of this thread http://www.deloreaneurotec.uk/viewtopic.php?f=12&t=495&p=4655 see the notes for Stage 4 for info on running with Volvo fueling and ignition components.
The air metering flap on the Volvo should be larger, 88mm wide vs a 78mm flap on the stock DeLorean metering unit.
Correct, the Volvo ignition dizzy has a better mid range advance curve.
For info here is a list of Bosch part numbers for the Volvo 260 and 760 (although only the 760 lists as B28 E/F)
56259
vwdmc16
05-03-2018, 10:46 PM
Oh the air meter is larger? Ill have to go measure that. I was hoping the throttle body would be bigger but they are identical, although somehow the throttle off that beat to hell volvo with 4 times the mileage is much smoother and tighter operating than my dmc unit.
vwdmc16
05-07-2018, 12:28 PM
Measured my Dmc vs volvo metering body, both are 80mm. So no real Difference in the bodies I can tell beside the pipe of agony connection is different.
MikeWard
07-03-2018, 04:28 AM
Measured my Dmc vs volvo metering body, both are 80mm. So no real Difference in the bodies I can tell beside the pipe of agony connection is different.
Strange, if they are the same then I can only assume it's for emissions requirements to allow the Volvo to be sold in the US.
Here is a top down shot of a Volvo 760 metering unit from a European Volvo 760 (left) next to a DMC metering unit (right). You can see that the circular disc is smaller and the housing slightly different on the DMC unit.
57115
vwdmc16
07-03-2018, 11:11 PM
I bet you are 100% right on that, Id bet there is only one US Epa approved size for volvo's Kjet on the b28F, hell I wonder if its the same part number from the B27F from the beginning of the PRVs imported in the US
But then its strange there are other minor emission things that differ on DMC vs Volvo B28Fs.
But hey, there were other K jet cars with simular designs, Years ago I found a late 80's Mercedes Ket metering unit and upper manifold at a local junkyard as an idea to cheaply hop up my PRV until I build a proper engine for my car.(long story short: it has an 88 mm air flap hole, bolts right on, superior design and quality) I wanted the try the individual cylinder adjustable ports this thing had to try and really dial in the cylinder fuel balance but decided not to as I realized how much dyno time that may take to even get running okay if its flow rates and ramps are way off/wrong. I also liked the improved CO adjustment access port, it wasnt plugged up and a pain to open up/seal but had a well made spring loaded head that sealed the air in the unit from vacuum leaks and was easy to use, a brilliant improvement for those two reasons BUT I never measured the main air inlet hole diameter as it never occurred to me until a few weeks ago that it might be bigger. Sadly I dont have the acutal internals for that hosing anymore, I kept the metering head and the stripped down body. Now im kicking myself for stripping it down that much and tossing the inards, this would have been a grear upgrade, even the air filter O-ring was the same size so the DMC airfilter works too! time to look out for another 1989-ish Mercedes 300? I forgot what model that it was.
vwdmc16
07-22-2018, 07:05 PM
Ive been pecking away at more smaller projects on the car to make it better, still feeling kinda down about the car as a whole but feeling feeling hopeful that improving a few key areas will make it much more enjoyable.
Finally finished rebuilding the UCAs with new Urethane bushings from DeloreanGo, some hand made boxing plates and finishing it off with black powdercoating.
one finished, one to go:
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180702_190449_zpsdvzmudns.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180702_190449_zpsdvzmudns.jpg.html)
Fully sandblasted and old bushings removed.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180702_193223_zpsmf06bklx.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180702_193223_zpsmf06bklx.jpg.html)
Original, bushings were looking quite sad, not fully failed but not trustworthy, I believe these are the last of the original suspension bushings.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180702_205353_zpsmy8dgpi8.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180702_205353_zpsmy8dgpi8.jpg.html)
UCA Reinforcement plates fitted and TIG welded up.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180702_193314_zps7las3xmw.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180702_193314_zps7las3xmw.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180702_195847_zpsi6brpvbd.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180702_195847_zpsi6brpvbd.jpg.html)
After another quick sandblasting and cleaning, the arms were powdercoated semi gloss black. Now the new bushings pressed in with sockets and a quick tool I made from a section of 1.5" tubing cut in half to support the thin sheetmetal where the bushing goes.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180702_194654_zpsruxukhsr.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180702_194654_zpsruxukhsr.jpg.html)
looking good and stronger than ever.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180702_195050_zpsd4x5o6jj.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180702_195050_zpsd4x5o6jj.jpg.html)
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180702_205414_zps9mt3chd7.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180702_205414_zps9mt3chd7.jpg.html)
The car has crossed the 70k mile mark, getting close to doubling the car's mileage since I purchased it in April 2009 with 36,800 miles.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180712_200403_zpsexwnjjzw.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180712_200403_zpsexwnjjzw.jpg.html)
The next critical preventative repair to do was the fuel pump, still running a OEM style pump that was renewed in 2001 by the PO. this pump has served me well be has been getting very loud on long drives and hot days. Time to upgrade while im in there. Installed a 2002 Chevy Tahoe fuel pump, went with a genuine Ac Delco unit which is a bit more expensive at $160 vs the knock off ones that can be had for as little as $50. Total cost for this fuel pump update was just over $300, which is a bit cheaper than the DMCH kit, I elected to keep using my OEM fuel level sender since it works quite well still.
The new parts: ended up returning a few of these as some of the fitting were too bulky and the V band wasnt the right size, thankfully the correct parts were actually cheaper.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180708_105259_zpspa4fmatd.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180708_105259_zpspa4fmatd.jpg.html)
Out with the old, I really want to repaint my trunk now, that should help me feel better about the car too.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180708_105305_zps0obhgvmy.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180708_105305_zps0obhgvmy.jpg.html)
First step, cut off this small alignment tab, don't need it here, a hacksaw makes good work of it.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180708_105328_zpsiq6xvan2.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180708_105328_zpsiq6xvan2.jpg.html)
Next a test fit, found my V band was too small at this point, also the fuel pressure sensor would have to go, installed a 6mm solid metal pin into the sensor's gasket with some fuel proof RTV to seal it up.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180708_105529_zpsnuubks8x.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180708_105529_zpsnuubks8x.jpg.html)
With the correct clamp and the fuel hoses installed with a nice Alcohol proof check valve installed. Fits in nicely.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180710_202611_zpspmgq9suh.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180710_202611_zpspmgq9suh.jpg.html)
Unfortunately no matter how I oriented the pump or pushed it down I could not get the pump cover to sit flush, looks like some fiberglass modifications are coming to this part too. Other than that I was very pleased with how the pump works, its practically silent.
http://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20180713_170900_zpsissvepvp.jpg (http://s31.photobucket.com/user/vwdmc16/media/DMC2/20180713_170900_zpsissvepvp.jpg.html)
powerline84
07-22-2018, 07:23 PM
Nice !
jawn101
07-22-2018, 08:15 PM
Those upper control arms look great! Any noticeable change in feel with the replacement bushings/strengthening?
Lwanmtr
07-22-2018, 09:24 PM
Looking good
vwdmc16
05-28-2019, 12:37 AM
Some big updates for you guys:
I built a new way to plumb the idle air motor, completely over the way the stock plumbing works with the "pipe of agony" I decided to re route the air from the intake plenum to the IAC motor by going around the back side of the fuel distributor with aluminum tubing.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20180926_171435_zpsjkag0ts8.jpg (https://s31.photobucket.com/user/vwdmc16/media/dmc3/20180926_171435_zpsjkag0ts8.jpg.html)
I used a small hole saw to make the 5/8" hole needed:
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20180926_171644_zpsnx6jy4oe.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc3/20180926_171644_zpsnx6jy4oe.jpg.html)
Then I TIG welded up the original hole where that damn pipe of never sealing agony would go.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20180926_180549_zpslulkeimq.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc3/20180926_180549_zpslulkeimq.jpg.html)
Next with a small assortment of old BMW secondary air injection tubing, A/C lines and fittings I laid out the new air pathway in a nice simple straight path to the idle motor:
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20180926_180501_zpshxmlrntl.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc3/20180926_180501_zpshxmlrntl.jpg.html)
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20180926_180540_zpsbkk2rehq.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc3/20180926_180540_zpsbkk2rehq.jpg.html)
Nice large clampable silicone coupler would make it easy to remove and ensure a great seal.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20180926_191446_zpszz0rm5lc.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc3/20180926_191446_zpszz0rm5lc.jpg.html)
Now to clamp the other end to the new hole I made, this bracket and bolt should do it:
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20180926_193017_zps0snpfipc.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc3/20180926_193017_zps0snpfipc.jpg.html)
This system has been working fantastically a much better idle and no more vacuum leaks.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20180926_193047_zpsmbxxwrba.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc3/20180926_193047_zpsmbxxwrba.jpg.html)
Back inside the car I finally got around to one of the biggest flaws which was the passenger side lower door panel. the arm rest area was broken off since I bought the car and was a constant source or squeaks and rattles any time a passenger would lean on it, I decided a new panel was a much better use of my time and money than trying to repair the old one. After nice call to Robert Grady I had a quality lower door panel ready to install, well unfortunately it didnt fit on my car as well as I was hoping.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20180903_152456_zpstbqy0y0j.jpg (https://s31.photobucket.com/user/vwdmc16/media/dmc3/20180903_152456_zpstbqy0y0j.jpg.html)
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20180903_144606_zpsst6vsfgt.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc3/20180903_144606_zpsst6vsfgt.jpg.html)
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20180903_144557_zps7loawvom.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc3/20180903_144557_zps7loawvom.jpg.html)
After a bit of tinkering I was able to move the upper forward bracket inwards and slotted one hole to reduce the gap, its not concourse quality but it will do for now. I also finally was able to get a pair of door air vents to replace the sad broken pair my car has had for many years, these little things sure make the inside a much nicer place.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20180903_144557_zps7loawvom.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc3/20180903_144557_zps7loawvom.jpg.html)
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20181103_160415_zpsgdnoobuh.jpg (https://s31.photobucket.com/user/vwdmc16/media/dmc3/20181103_160415_zpsgdnoobuh.jpg.html)
Wow that picture is too big
vwdmc16
05-28-2019, 01:02 AM
About two weeks after installing stock cams again I noticed some coolant leakage again on the floor, after investigating I found that the new head gaskets were not sealing, I was having leakage on the perimeter of the cylinder heads and into the valley. The heads would have to come off again.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20180923_210934_zpscqvnbpus.jpg (https://s31.photobucket.com/user/vwdmc16/media/dmc3/20180923_210934_zpscqvnbpus.jpg.html)
After getting the heads off it was easy to see the gaskets I used were not up for the task of sealing the heads to the block, the "aftermarket" gasket set was not the correct choice even though it came with the rest of the engine gaskets needed to do a top end reseal, lesson learned, stick to quality name gaskets. the cheap gaskets failed in an odd way, the composite paper of the gasket had become very water logged and soft, as if the coolant broke it down into a mush, very odd.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20180920_072721_zps0tzhluwx.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc3/20180920_072721_zps0tzhluwx.jpg.html)
Re assembled again and the engine has been staying dry for a few about 5k miles now. As you may have noticed I had the stock exhaust back on again, another one of our terrible Biannual smogs required it, I still wasnt able to find a local smog shop that would pass my DMCH system, I hope that is the last time I have to swap back to that.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20180920_072936_zps3yu4k3eb.jpg (https://s31.photobucket.com/user/vwdmc16/media/dmc3/20180920_072936_zps3yu4k3eb.jpg.html)
I also picked up a bunch more little parts, more fuel lines-no more originals left on the car, new heater motor resistor connector as mine began to melt, new LEDs, and spare gaskets.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20181123_180836_zpsorotklkv.jpg (https://s31.photobucket.com/user/vwdmc16/media/dmc3/20181123_180836_zpsorotklkv.jpg.html)
Back in the interior i decided the smashed up seat backs could use an upgrade too:
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190327_174731_zpsp4jzadf2.jpg (https://s31.photobucket.com/user/vwdmc16/media/dmc3/20190327_174731_zpsp4jzadf2.jpg.html)
Some .080" aluminum would be much stronger than that fiberboard.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190327_181011_zpsd114rdwt.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc3/20190327_181011_zpsd114rdwt.jpg.html)
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190327_184115_zpsaqphf9it.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc3/20190327_184115_zpsaqphf9it.jpg.html)
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190327_185826_zpsvckon8wl.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc3/20190327_185826_zpsvckon8wl.jpg.html)
Riley88
05-28-2019, 02:05 AM
About two weeks after installing stock cams again I noticed some coolant leakage again on the floor, after investigating I found that the new head gaskets were not sealing, I was having leakage on the perimeter of the cylinder heads and into the valley. The heads would have to come off again.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20180923_210934_zpscqvnbpus.jpg (https://s31.photobucket.com/user/vwdmc16/media/dmc3/20180923_210934_zpscqvnbpus.jpg.html)
After getting the heads off it was easy to see the gaskets I used were not up for the task of sealing the heads to the block, the "aftermarket" gasket set was not the correct choice even though it came with the rest of the engine gaskets needed to do a top end reseal, lesson learned, stick to quality name gaskets. the cheap gaskets failed in an odd way, the composite paper of the gasket had become very water logged and soft, as if the coolant broke it down into a mush, very odd.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20180920_072721_zps0tzhluwx.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc3/20180920_072721_zps0tzhluwx.jpg.html)
Re assembled again and the engine has been staying dry for a few about 5k miles now. As you may have noticed I had the stock exhaust back on again, another one of our terrible Biannual smogs required it, I still wasnt able to find a local smog shop that would pass my DMCH system, I hope that is the last time I have to swap back to that.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20180920_072936_zps3yu4k3eb.jpg (https://s31.photobucket.com/user/vwdmc16/media/dmc3/20180920_072936_zps3yu4k3eb.jpg.html)
I also picked up a bunch more little parts, more fuel lines-no more originals left on the car, new heater motor resistor connector as mine began to melt, new LEDs, and spare gaskets.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20181123_180836_zpsorotklkv.jpg (https://s31.photobucket.com/user/vwdmc16/media/dmc3/20181123_180836_zpsorotklkv.jpg.html)
Back in the interior i decided the smashed up seat backs could use an upgrade too:
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190327_174731_zpsp4jzadf2.jpg (https://s31.photobucket.com/user/vwdmc16/media/dmc3/20190327_174731_zpsp4jzadf2.jpg.html)
Some .080" aluminum would be much stronger than that fiberboard.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190327_181011_zpsd114rdwt.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc3/20190327_181011_zpsd114rdwt.jpg.html)
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190327_184115_zpsaqphf9it.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc3/20190327_184115_zpsaqphf9it.jpg.html)
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190327_185826_zpsvckon8wl.jpg (http://s31.photobucket.com/user/vwdmc16/media/dmc3/20190327_185826_zpsvckon8wl.jpg.html)
great stuff but check the pipe with the otterstat, the otterstat should be facing the floor not facing up tbh
vwdmc16
05-28-2019, 04:37 AM
After hitting 72,00 miles its time fore more upgrades:
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190112_092901_zpsqb4f2urs.jpg
I wanted to make the front suspension feel more solid and safer, so I built some LCA braces. I purchased some urethane bushings that fit into 1.50"x .120" wall steel tubing, im unsure of the durometer of this urethane but it believe it to be around 75D. these bushings were cheap as well. just $8 each.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190212_135909_zpsilgya5fi.jpg
After some measuring I mocked up some arms with some 1" tubing to connect the inner pivot point with the lower shock mount.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190227_194632_zps6ysvgrni.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190227_194959_zpsrniss2kh.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190227_195032_zpsnxnzuckq.jpg
Happy with the fitment I powdercoated them and installed with new longer bolts, some 6" and 8" grade 8 bolts replaced the stock suspension bolts as well as some large thick fender washers to make sure the bushing stays in place. Still need to fully paint the front frame section.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190228_201718_zpsodteptcw.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190228_202515_zpsezcijpsx.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190228_202529_zpsf3xehkps.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190228_202635_zpsznzgu3gm.jpg
Those braces had a great effect of making the car much more stable under braking. After that success I wanted to rebuild my adjustable rear upper links with stronger parts. These parts also came from teh same place I bought the front bushings, Barnes4x4.com
These self contained and grease-able urethane turnbuckle style joints have a 1/2" ID and are the same width as the stock links, they connect to 3/4" threads to some heavy duty threaded sleeves. with one side reverse thread I can easily adjust my rear camber. I made these able to become longer than stock as I dont need more that the -3.2 degrees of rear camber I have at this lowered ride height. Setting the rear to -1.8 degrees has worked great.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190308_172100_zpsmscj8ztc.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190308_180116_zpsq6cpyhbs.jpg
Powdercoated and assembled
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190308_184351_zpsgm2xtfes.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190308_190036_zpscdbpi4nm.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190308_192443_zpsjfxfkh2k.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190308_192450_zpsjw1wnmii.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190308_192506_zpsthknvypf.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190227_182835_zpsbm5gbca4.jpg
vwdmc16
05-28-2019, 04:52 AM
great stuff but check the pipe with the otterstat, the otterstat should be facing the floor not facing up tbh
If I set it up facing down, the exhaust will burn the wiring when the DMCH headers are on, there is so much water flow when the engine is running the chance of a air pocket to stay on that sensor is very low.
vwdmc16
05-28-2019, 04:58 AM
A few more small repairs: rebuilt the rear brake calipers, the last clean up and painting with POR15 did not last. Stripped down, blasted, and powdercoated, rebuilt the parking brake calipers too but I doubt they will ever work as well as Id want them to.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190409_171603_zpsdvdhkcpn.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190409_192055_zpsiaifh4eh.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190410_194934_zps10qetkg4.jpg
All the original tail light nutserts were rusted/ cross threaded over the years, time to drill the, out and replace them with M5 rivnuts and some smarter looking stainless allen head bolts.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190323_200313_zpsflbltfjm.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190323_200601_zpsmg1wkyls.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190323_200918_zpsbyxuv7se.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190323_202722_zpssxf58dft.jpg
nkemp
05-28-2019, 03:28 PM
I like how you think ... and what you can accomplish. If only Vulcan mind-melds worked!
BTW ... no smog checks in MN... just saying ... we'd be happy to have you here:)
vwdmc16
05-28-2019, 09:07 PM
Thanks man! I doubt I could handle the cold out there, I'm from Arizona.
nkemp
05-28-2019, 09:26 PM
Thanks man! I doubt I could handle the cold out there, I'm from Arizona.
Too much heat or too much cold .... there are only so many layers of clothes you can take off in the excess heat. Plus not everyone should do that:shock:
Keep up the good work and posting it.
jawn101
05-29-2019, 01:38 AM
That new idle pipe routing looks awesome! Did you try the new computer yet? How is the overall idle treating you?
Also, wow - new door panels? I’m pumped you’re getting to some of the interior cosmetics!
vwdmc16
05-29-2019, 04:27 PM
The idle was working great for about a week, now its inconsistent again. Once hot it wont go below 1100, sometimes higher. If connect power to the ISC to fully close the valve the engine always stalls, I'm thinking the idle controller just wont restrict the air enough to give a proper idle. I've yet to try the new idle ECU. Engine is still out of the car.
Bitsyncmaster
05-29-2019, 05:22 PM
The idle was working great for about a week, now its inconsistent again. Once hot it wont go below 1100, sometimes higher. If connect power to the ISC to fully close the valve the engine always stalls, I'm thinking the idle controller just wont restrict the air enough to give a proper idle. I've yet to try the new idle ECU. Engine is still out of the car.
The stock idle ECU never closes the idle motor fully. My bet is your deceleration valve springs are bad.
vwdmc16
05-29-2019, 10:03 PM
My decel springs are removed and soldered shut.
I'm really hoping your idle controller does the trick .
nkemp
05-30-2019, 07:35 PM
Are you sure it is the idle control holding the RPM up and not the spool?
I have trouble getting my spool to drop to the neutral position, to the point where idle takes over. It is as if there is a dead spot as the spool return to its neutral position.
I suspect if I readjust the control arms so that the returned position in not at the 6 o'clock position but closer to the 7 o'clock position it would work better.
vwdmc16
07-04-2019, 12:43 PM
Hey guys,
I decided to get a new brake booster as I felt my car's brake performance had declined over the last few months and pedal effort was higher than I remember before. After a quick test of driving around the block, then disconnecting and plugging the vacuum supply to the brake booster before another lap around the block; it was very easy to tel that my brake assist from the booster was pretty much gone. So a few days later a new booster arrived from DPI:
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190410_203152_zpsjkebcuw6.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190410_203058_zpsbgztkduu.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190410_203112_zpsye4muhiv.jpg
Wasn't fun to install but not the worst job, I was able to get the old out and the new in without opening the hydraulic circuits, just gently pulling the master cylinder to the side. Impressions: The brakes were much more powerful again. Far less effort required, however the first 25% of brake application feels more sensitive than the original booster, not in a bad way but it something to get used to. I was able to compare it side by side with an original booster and the DPI does feel lighter to the touch.
Continuing with brakes, Ive been trying a new Mazda Miata configuration: 2001+ 1.8 Sport brakes which I now feel is superior to the regular 1.8 miata brakes.
larger calipers which still bolt onto the Shattenkirk brackets.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190301_082354_zpsilgyg1du.jpg
270mm rotors, are a little bigger than the regular 1.8 and obviously bigger and vented over stock.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190304_202008_zpsiev7thmp.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190304_202105_zpskomrafks.jpg
1.8 vs 1.8 Sport:
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190104_214437_zpsl9lih60w.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190301_180654_zpsok893yyj.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190304_203312_zpstcejpaug.jpg
Being a larger set up it will not fit in a 14" wheel and its actually kind of tight in a DMC 15" wheel, a tight group of fitting was needed to clear. So some more development required but im quite happy with the performance of this caliper. For those of you wondering about the Stoptech kit I had, Im still going to use it, but im waiting to get a new custom sized caliper set so I can go four wheel StopTech.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190304_202644_zpsyq2p2ygu.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190305_202923_zpse9i2m5t7.jpg
vwdmc16
07-04-2019, 01:08 PM
Another late night experiment to improve the feel of my car on the road, increasing front Caster. I work on BMWs all day and whenever I align them I see how much Caster the front suspension has compared to other makes, such as a Delorean, or atleast my Delorean that only had 2.7 degrees of caster where some Bmws have 9 degrees. Caster is not adjustable stock so to allow this I could have to move the upper control arm rearward in relation to the lower arm.
luckily there is about 10mm of material to remove on the the frame's shock tower, by adding a spacer to the rear side the upper arm moved in relation to the frame and lower arm, adding caster.
Driver side:
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190307_185100_zpsdzuaufcl.jpg
Shims for the test alignment, a full solid spacer will be made when I get the numbers I want.
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190307_191559_zpskeivlddr.jpg
Moving the Upper control arms rearward 9mm gained me 2.8 degrees to a total of 5.5 caster. Need to tune that rear tow a bit more.
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190307_193345_zpsc2dwrnuj.jpg
No regrets with that modification, it really helped the way the car tracks down the freeway at high speed. Steering feels extra planted and centered, low speed steering effort has increase a little but not enough to complain about. The increased caster, front LCA braces and the wider 15" wheels have changed the front end characteristics quite alot over stock, and for the better in my opinion.
After than I received some tired old original LCAs from a friend and decided to clean them up, box them, powdercoat, then install new bushings and balljoints. always good to have spares.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20181124_175258_zps7rsceybz.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20181127_191403_zpsjjepbwxl.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20181127_191513_zpsqqrr6pmd.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20181129_182226_zpsjpt7g8i8.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20181129_182201_zpspaoa2sji.jpg
Lwanmtr
07-04-2019, 05:14 PM
Looking good
vwdmc16
12-10-2019, 02:51 AM
Time for some new camshafts, I decided to pull the whole lump for a good clean and some more updates too:
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190617_224402_zpsqwswsgxi.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190617_215513_zpstheln53z.jpg
Im glad it came out with the Headers attached but it was a bit tight.
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190422_210303_zpshv1inxco.jpg
Up on the stand, First remove the timing cover, valve covers and chains, then the rocker shaft can be pulled out
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190525_212537_zpsnoy5pyo1.jpg
yes I hide Oreos in the garage so the wife doesnt eat them all.
Loosen all the adjuster as much as possible
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190525_212533_zpspa4yy492.jpg
Keep everything in the order it came out, very important. Ideally you want new rockers with the new cams, very pricey I elected to polish the cam follower faces to give it a new face for the new cam to touch,
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190525_212716_zpsdihp1jv3.jpg
Now the cams can slide out when the rear access cover is removed.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190525_212720_zpsouj9stno.jpg
Remember to pull the distributor drive up a little. the engine was set at TDC beforehand so the distributor should go right back in but will need to verified after the new ones are in.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190525_213355_zpszglgo1xk.jpg
New versus old, not much different but they are.
https://i31.photobucket.com/albums/c396/vwdmc16/dmc3/20190525_213446_zpsteosdkvq.jpg
Old cams out, new ones just slide back in with assembly lube. Rockers go back in reverse of disassembly and then repeat on the other bank.
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190525_214319_zps2hkz1j4r.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190525_231116_zpsszdctsya.jpg
Now getting the new ones lined up correctly is not trivial now that my heads have been decked slightly and these are custom ground cams, They need to be dialed in like I have documented before with a large degree wheel and a dial indicator. If installed like the Factory manual indicated, one cam was off 6 degrees, the other was 4 degrees. Both cams retarded to the correct setting which robs me of high RPM power. Pictures would explain this much better but I did not photograph this as a How to.
The short of it it was that I would need to drill new holes in the cam gears to set the cams at the correct position in relation to the crank.
I set the crank in the position I wanted for cylinder #1's intake cam lobe to open the valve 0.050".
Removed the cam sprocket and pressed out the pin that locks it to the cam.
I re installed the cam gear a bunch of teeth off off from its original position and installed the chain with tensioner, now without the locating pin I could rotate the cam independently of the chain drive.
I rotated the cam to the correct position I needed as indicated with the dial indicator to get 0.050" valve lift.
Now I could mark a new position for a new pin using a sharp pick in the groove that holds the cam sprocket pin.
Removed the cam gear again and using the stock reinforcing washer as a centering guide over the marks I made, I center punched the location for the new hole.
Drilled a pilot holes and undersized hole for the pin with a drill press. Chamfered the hole smooth, very important the pin is a tight fit as you dont want that falling out. Tack welding the pin to gear after confirming is a good idea.
Pressed the pin in the new hole and with reinforcement washer.
Reassembled and confirmed the cams were now matching the cam card.
Repeat on the 4-6 bank.
New hole drilled in the cam gear:
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190609_094235_zpsinboj1jk.jpg
Now I didnt get the first hole spot on, it was still 2 degrees off. So I repeated with the cam gear rotated a few more teeth. There is enough room to do this about 6 or 7 times before you would need a new gear or weld up the old holes. Here it is installed.
Now obviously the Factory cam gear mark is no longer valid but finally the cams are in correct time again. What a relief, i should have don that years ago with the first set of cams
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190609_104224_zpsooly9tun.jpg
Reassembled and ready to run properly now
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190422_210316_zpsvjks167s.jpg
Lwanmtr
12-10-2019, 07:56 AM
Looks good...waay beyond my skillset to undertake something like that.
nkemp
12-10-2019, 10:27 AM
Nice work. When I do a "a good clean" it usually means a sponge and soapy water.
jawn101
12-14-2019, 09:17 AM
Looking great as always, man!
vwdmc16
04-04-2020, 11:22 PM
One more item I upgraded while the engine was out was a oil pan baffle, ive noticed loss of oil pressure on really hard turns. This 1/8" thick aluminum plate I TIG welded into the pan should help keep the oil from sloshing up the side wall of the crankcase. upon assembly I found the dipstick needed a hole to reach the bottom of the pan so another small hole was made on the driverside to allow that. After some testing since installing this ive determined the baffle helped but does not completely solve the oil starvation issue.
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190606_134526_zpskpflszh8.jpg
While the engine was out I sent my window switches off to Dave Mackeen to have the illumination LEDs repaired, they both burned out the LED on a few months after I installed them initially, very odd; but nice to have them back.
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190618_124958_zpsgmgexffz.jpg
To help with improving how the car runs when cold I upgraded the oxygen sensor to a 3 wire set up so It can heat up much more quickly. I made a new connection with a three pin Deutch plug to power it off the Idle ECU power source behind the driver seat. the sensor is a Bosch unit from a 90's buick, the ones with a 3.8 v6. One signal, one power and the third is ground. I used metal P clamps and 5mm Rivnuts to secure the wire away from the suspension. I noticed an improvement in how quickly the Lamda system comes awake and stays awake which had been an occasional issue with the DMCH headers.
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190724_185046_zpsqyjwi8je.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190724_185007_zps06steqer.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190724_184946_zps2gcubgvp.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190724_184955_zpsfnfjnp03.jpg
The car was running nicely so I decided to take it for a solo trip over the mountain to Nevada to visit family, Stopped for a photo on this nice vista overlooking Donner lake.
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190811_125116_zpsd7kdaovy.jpg
Also had time to see my old favorite, the Gold car at Harrah's Auto Museum. My car worked great the whole trip!
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190812_115655_zpswxepp6a9.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190910_192544_zpsjvphr4nn.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190910_192559_zpsyxenl1qf.jpg
vwdmc16
09-08-2020, 01:30 AM
Hi everyone, feels like another year has gone by, just 5 months, anyways not that many big things with the car. Ive been working on a few local cars that need more work than my car, and they help pay for my silly projects.
New fuel hoses, cv boots and seals for Maor:
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20200704_105430_zpsyzj70ef6.jpg
New exhaust and A/C for this lovely painted car. I worked on this car a number of years ago when the previous owner had it, sadly he has passed but now his son in law owns and enjoys it, plenty of upgrades coming.
New DMC CA California legal exhaust!
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20200706_093106_zpsdhuc3eyf.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20200706_094748_zpsfpebgvoy.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20200710_175616_zpsioplfygc.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20200706_174443_zps1vsxhvvb.jpg
I replaced my noisy cheap no name power antenna with a lovely West German Hirshmann unit from a '89 BMW. Made a custom bracket as the ones ive seen for sale look a bit flimsy. 14ga steel and powder coated, installed with fresh rivnuts and fully adjustable.
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190922_182905_zpsaiaommas.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190922_191615_zpsrad99kff.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190922_191731_zpsgxt3wfal.jpg
All the tools needed to install.
Still need to wire it up, its electronics are self contained so no separate relay in the ECU box, but it does work very smoothly with a new mast, extremely quiet and tall.
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20190923_220305_zpsgdqoq5y1.jpg
Replaced the seals and pistons on the LF caliper as it was starting to leak, old corrosion. Works a treat now, still planning to go 4 wheel Stoptech but more pressing matters are at hand so im fine with good working stock clampers
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20191006_125528_zpsiwp9x776.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20191006_125536_zpsliznxbyq.jpg
Bought a NOS luggage rack, havent put it on yet, while it was "new" there was large rust spot bubbling through the paint on the center tubes. So maybe after that gets re powder coated. Still its a nice bit of kit.
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20191009_194014_zps7vwodkuv.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20191009_193945_zps0uecrra1.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20191009_193941_zpstvykprow.jpg
Picked up a empty PRV to use as a mock up to build a new intake manifold, I want o do some dyno testing versus stock.
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20200803_195143_zpsguqh9qhc.jpg
https://i31.photobucket.com/albums/c396/vwdmc16/DMC2/20200805_173243_zps8rhwy46n.jpg
The photo you've posted on Donner lake is just amazing!
Really good job done on the car, as always.
The white DMC also look really nice, is the owner a member here?
vwdmc16
09-09-2020, 02:15 AM
Thanks! Here's some more beauty pics from my drive up in the hills on my last birthday.
https://hosting.photobucket.com/images/c396/vwdmc16/20191228_112450.jpg?width=1920&height=1080&fit=bounds (https://app.photobucket.com/u/vwdmc16/a/11c3b01a-5d10-4b0c-8d04-cec97f51515b/p/2860bbf0-52c1-4a75-aa8f-b8853b0bfc0c)
https://hosting.photobucket.com/images/c396/vwdmc16/20191228_123148.jpg?width=1920&height=1080&fit=bounds (https://app.photobucket.com/u/vwdmc16/a/11c3b01a-5d10-4b0c-8d04-cec97f51515b/p/4eecfef9-5820-476f-9c4b-3de091dfd5a9)
https://hosting.photobucket.com/images/c396/vwdmc16/20191228_123218.jpg?width=1920&height=1080&fit=bounds (https://app.photobucket.com/u/vwdmc16/a/11c3b01a-5d10-4b0c-8d04-cec97f51515b/p/7bf3786a-322b-4a5a-89c9-1634e95ba276)
Finally had some time to full strip down the front end for a good coat of paint on the frame, also fully powdercoat the last of the parts that were only coated in POR15 from years ago.
https://hosting.photobucket.com/images/c396/vwdmc16/20200418_140518.jpg?width=1920&height=1080&fit=bounds (https://app.photobucket.com/u/vwdmc16/a/11c3b01a-5d10-4b0c-8d04-cec97f51515b/p/628c1785-6bd5-4584-8dad-6b70de5f9607)
https://hosting.photobucket.com/images/c396/vwdmc16/20200418_143801.jpg?width=1920&height=1080&fit=bounds (https://app.photobucket.com/u/vwdmc16/a/11c3b01a-5d10-4b0c-8d04-cec97f51515b/p/fff5d583-a239-4bdd-bc5f-a8f8488ca7f7)
https://hosting.photobucket.com/images/c396/vwdmc16/20200414_202205.jpg?width=1920&height=1080&fit=bounds (https://app.photobucket.com/u/vwdmc16/a/11c3b01a-5d10-4b0c-8d04-cec97f51515b/p/844df4d9-bd82-4916-8c6c-6ac5d1d2e7aa)
Powdercoated, and reassembled with new hardware, had to have the coolant pipes and sway bar professionally done as they are too large for my oven.
https://hosting.photobucket.com/images/c396/vwdmc16/20200414_192118.jpg?width=1920&height=1080&fit=bounds (https://app.photobucket.com/u/vwdmc16/a/11c3b01a-5d10-4b0c-8d04-cec97f51515b/p/65051720-f198-4034-81c0-ddd89a059110)
https://hosting.photobucket.com/images/c396/vwdmc16/20200414_192100.jpg?width=1920&height=1080&fit=bounds (https://app.photobucket.com/u/vwdmc16/a/11c3b01a-5d10-4b0c-8d04-cec97f51515b/p/6bbb4948-7ded-4dc6-bc06-292476daff93)
https://hosting.photobucket.com/images/c396/vwdmc16/20200512_193344.jpg?width=1920&height=1080&fit=bounds (https://app.photobucket.com/u/vwdmc16/a/11c3b01a-5d10-4b0c-8d04-cec97f51515b/p/f466b676-832e-42fb-a116-272abd9c3f61)
Prepped the frame and masked up the spots I didnt want painted, just Rustoleum machine grey.
https://hosting.photobucket.com/images/c396/vwdmc16/20200426_005013.jpg?width=1920&height=1080&fit=bounds (https://app.photobucket.com/u/vwdmc16/a/11c3b01a-5d10-4b0c-8d04-cec97f51515b/p/8dc3a67c-7ff3-4b46-bec0-23875bccd048)
https://hosting.photobucket.com/images/c396/vwdmc16/20200426_005024.jpg?width=1920&height=1080&fit=bounds (https://app.photobucket.com/u/vwdmc16/a/11c3b01a-5d10-4b0c-8d04-cec97f51515b/p/53e8a784-9cbc-4082-bb1d-2f0438ba6e7d)
https://hosting.photobucket.com/images/c396/vwdmc16/20200426_005034.jpg?width=1920&height=1080&fit=bounds (https://app.photobucket.com/u/vwdmc16/a/11c3b01a-5d10-4b0c-8d04-cec97f51515b/p/de5fbccc-6cba-48af-89b1-157d58390748)
After two coats it was time to fully assemble all clean, Also finally have the correct sized front Stoptech pistons much better!:
https://hosting.photobucket.com/images/c396/vwdmc16/20200515_220247.jpg?width=1920&height=1080&fit=bounds (https://app.photobucket.com/u/vwdmc16/a/11c3b01a-5d10-4b0c-8d04-cec97f51515b/p/b89c8279-5c97-4610-a488-f39bb7eedbf5)
https://hosting.photobucket.com/images/c396/vwdmc16/20200515_220258.jpg?width=1920&height=1080&fit=bounds (https://app.photobucket.com/u/vwdmc16/a/11c3b01a-5d10-4b0c-8d04-cec97f51515b/p/3c56a6b0-7244-436e-a476-fa622e7b3f9b)
https://hosting.photobucket.com/images/c396/vwdmc16/20200515_220322.jpg?width=1920&height=1080&fit=bounds (https://app.photobucket.com/u/vwdmc16/a/11c3b01a-5d10-4b0c-8d04-cec97f51515b/p/2acde3cc-c3d3-4a01-b225-756b051b473d)
https://hosting.photobucket.com/images/c396/vwdmc16/20200515_220336.jpg?width=1920&height=1080&fit=bounds (https://app.photobucket.com/u/vwdmc16/a/11c3b01a-5d10-4b0c-8d04-cec97f51515b/p/9f83583b-fc7e-40f0-ba3d-606dbdc8bafe)
https://hosting.photobucket.com/images/c396/vwdmc16/20200517_011449.jpg?width=1920&height=1080&fit=bounds (https://app.photobucket.com/u/vwdmc16/a/11c3b01a-5d10-4b0c-8d04-cec97f51515b/p/85ac866c-d5fd-4f51-b804-b0f64053f958)
Lwanmtr
09-09-2020, 03:56 AM
Awesome work.
andyo
09-10-2020, 09:15 AM
Great Work Clint! Its great to see the updates.
Sent from my iPhone using Tapatalk
vwdmc16
09-01-2025, 11:27 PM
Hey everyone! A new record for me not updating this, nearly 5 years! ugh I know, sorry. I want to get back into updating this more,
not just for those of you still reading this but for my own personal records and nostalgia.
I'll need to dig up the phots of the major events the car has has over the last 5 years but to honest there hasn't been nearly as much as before.
The real short of it is that for a few of these last years I've kinda lost my passion for the Delorean and the community,
its back a bit now but I had so many frustrating delays, and minor issues that built up to me no wanting to keep pouring my heart into this machine that wasn't returning the love on top of frustrations at work and with my personal life, this car has been put in the back seat.
Another reason for lack of posts is as we have all seen the sad truth that car forums are dying off fast, I really hate that Facebook did that,
its an awful format that wont have any good records for the future, its all about showing off and arguing about current trends and issues.
Id like to see this platform going as long as it can.
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/dbe86f3c-ebcf-4756-b515-6fe849c14a83.jpg
Otherwise the car has still been quite reliable, only recently the K jet has given me more big headaches, I think I have is ready again for yet another Smog here in California.
But lets go over the big mile stones I can remember and Ill go into them more with photos as I get them uploaded:
June 2024: Car is at 87,700 miles
August 2025 88,900
1: Brakes: Im still running the StopTech St43 4 piston calipers and 280mm rotors up front and stocks in the rear.
I've made bolt-on brackets to install the same type calipers in the rear with a lightly modified 300 mm rotor from the front of a Mini Cooper R56 JCW.
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/dad68a4b-029a-4a8b-a3ef-b32970ae3887.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/6a4bf160-f0ae-4277-bde2-dfafb53992dc.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/e4271e99-1e7f-4ba8-9284-e0530a939de1.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/5469989d-9ba7-4037-b02a-61780294d425.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/0bbd33da-9f1c-4f2f-bead-ed706db4457d.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/4eeab939-cc33-415b-b984-814470fc4e7a.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/c52438ad-91cb-404c-993c-7f97f128558b.jpg
However I will need custom made caliper pistons to get the rear brake balance correct while still using the stock DMC master Cylinder.
This does not give a parking brake option, my plan was to add another bracket off the trailing arm to mount a Universal Willwood electronic parking brake caliper.
No plans to get that done soon. I have about 8k miles on this current set up and while its stronger than stock, I still dont love it.
Its a bit more sensitive than I wanted and makes more brake dust that anyone wants.
2: Suspension: My 2021 Ive gone to a KW v2 coil over set up since May 2021. I really like it, definitely better than any other set up ive tried.
I didnt like the colors of the purple and yellow so I re-powder coated the springs on day one.
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/7d990157-e0f4-49f7-85e3-bd1530aecf64.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/017dcfff-fe32-453d-9b94-c63dfd092400.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/6c2acd04-420e-47cc-84e3-1a4d959e6061.jpg
I also made these short front lower arm braces from 1.25" DOM to triangulate and secure under braking. Works fantastic
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/13f188f6-77ac-4e4d-865c-3248ea50d631.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/a6244379-0d32-4836-9ea2-47dab00f6bfe.jpg
4k miles on it the system was working pretty good untill about 6moths ago when ive been having a possible front spring failure.
the car would bottom out and really bang on the front left corner over speedbumps and clockwise on ramp.
Raising the spring does nothing to change ride height. its very odd. Ive ordered a taller and heavier spring from Eibach, 70mm 285in/lbs 200mm springs.
Unfortunately those have been on permanent back order since ordered in February '24 So I ended up buying a set of some weire branded Japanese universal springs.
285ft/lb and 9" long was about an inch too much but I was able to get them in and it made a huge difference, Car feels so much better that it actually has travel
and a good spring rate. Now to do the same for the rear to help reduce body roll, The car also finally has full Urethane bushings too.
In April of '22 I stopped using the BFG rear tires and with to Toyo R888R in 235-50-15 size which sadly do not look anywhere as well fitted to the car as a 60 profile does.
But the rear has way more grip and less sidewall deflection, really pushes the limits of the suspension and brakes!
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/e39e126b-e121-44b1-81ab-fafb1f4f4e24.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/66a74194-daf8-40e5-ae56-9de58fb9169b.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/5ea2102f-f3ea-421c-95e2-e98e02b86e42.jpg
Interior: New seat covers!
November 2021 finally I fixed the biggest blemish of the interior by installing the nicest seat covers from DeloreanGo. stripped and powder coated the seat frames after fixing broken welds too. Amazing how much better they work!
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/36d22272-63ce-46a9-9ad7-a4ab93832e8b.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/55ecd2ae-3810-42ce-82b5-db1503343a17.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/2ccfc625-698a-4920-87dc-e635e0ee3f75.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/cc78af56-d213-47f9-8e5e-9cae73db46b1.jpg
Really like them alot, they fit very well and look like the originals do. i just wish they kept that strong leather smell longer,
still need to do the steering wheel and Binnicale, also have a big crack in my Glove box door, boo. Ive kinda given up on thinking to re do the interior in Suede.
.......CONTINUED.......
vwdmc16
09-02-2025, 12:32 AM
Some other fun, Had this great photo shoot with this photographer that wanted to make his own version of a Album cover for his favorite band Daft Punk that was breaking up at the time.
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/1b92135f-e723-4372-b87b-35a0a6a445cb.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/e35dbc38-11f8-4e13-8599-a2d502a1ceb4.jpg
Had my wheels sandblasted to be be re coated all in the same dark grey, after a wrong color that looked more like primer was done I finally got the color I wanted, Its called Black Chrome but looks like a great early grey, Sadly my powder coater guy stopped talking with me after just doing the one test wheel....
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/74caffca-3b3e-406a-8a5b-8d92abb664c8.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/fc4041a3-22dd-4bd5-a670-15c3d6fe01b7.jpg
2023 my heater core started to leak so the last big item ive not touched on my car the HVAC came out for a full refresh and reseal. New heater core, the AC works much better with all the leaks sealed but sadly the heater is not quite as strong as it once was
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/160f15e9-90a5-4c44-b390-d78d823e34a5.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/5b0bd5f0-b19b-4d4b-8d4d-6517830ae42e.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/36b28593-b612-44bd-94ab-1166a1b630df.jpg
CRASH!!!!!!
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/6cb4fd36-a9bd-480f-b4b6-ad9b1f997912.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/40007918-61fa-4d35-9985-0881357b8c25.jpg
Yeah it was bound to happen sooner or later. One evening on the way home from a car show driving south on Interstate 5 I ran over
something that looked like a large bumper shock or a McPherson strut, It went right under the driver seat avoiding the tires but hit my front frame horn,
punching a hole in the 0.120" thick DOM tubing
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/03aa2058-8f49-4987-9399-9fe942bd9240.jpg
Went under the floor scratching the tub and punching a big hole in the storage cubby behind me:
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/b19a90a0-a135-4d8d-a48e-cdb1c92b85e7.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/6920ed39-e860-4eb7-a222-68895a0c6aef.jpg
Balled up the trailing arm shield as you saw above, bent my lower rear control arm
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/d3d9c720-48f9-4ea1-acfc-1c54f0d68670.jpg
Put a large hole in the DMCH exhaust after the cat.
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/5f1e25dd-383b-4871-9107-0b30a88f7641.jpg
The impact was hard enough to crack the windshield and pop the inertia switch.
Thankfully I didn't loose control or hit anyone but that metal took out some other cars. I was able to limp home a mile and access the damage more.
Stupidly I filed a claim with insurance and of course they think a few dents in holes in fiberglass will cost $55k to repair and wanted to total the car.
NOPE, retracted claim, I'll fix it myself for a grand. Still mad about that and ever since then I really havent been driving the car near as much for fear of the insurance being poor.
I cant raise the agreed value until its all repaired and inspected again, still they may not want to cover it.
I still wont go back to Hagerty after my Volvo crash they want a ridiculous premium for my DMC too.
Engine swap:
Ive wanted to do this before I even had the car and somehow after 15 years ive still not really started it, until recently. Ive toyed with the idea of a few different engines. I mocked up a few just to see how viable they could be:
Honda k24 with the original transmission ( right before anyone had finished one)
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/e1f7d0c8-75af-4787-8782-dd2cddae2d2c.jpg
But Ive become a real BMW guy the last 10 years so How about a BMW M62 v8!
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/41760e73-3a8d-48ca-b227-44ce9b623e67.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/d6b9ad11-b10f-4c0c-82b5-6c2a83d54d5c.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/1ac9e7aa-34ea-40c0-ae8e-24549662ad33.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/42e622c5-3a6f-4de0-95d5-09516cde206b.jpg
I was more into the straight 6 engine though. so I was leaning towards a M54 3.0, all aluminum, solid engine. Although I think the next generation called the N52 would be even better as its a blittle more power (270hp and is the lightest 6 they ever made with all the magnesium they have
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/dc75a096-7a22-4ec7-831a-7874bb36f2c5.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/2ae2607a-a550-41af-8de8-95bf5e99dec0.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/128f3bab-f210-409e-b5d0-dbb86ef13564.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/4744ca70-4702-42ea-b13d-f7685dfa489b.jpg
The ultimate in silliness would be the BmwM70 5.0L V12, does not fit well, but imagine a v12 Delorean!
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/a5e42811-75bd-471e-90e0-068566d57104.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/6bd0b94b-6827-4cb7-8082-e534e66fba48.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/492151f4-b4c7-4189-a0a8-3c85752207eb.jpg
So back into reality ive decided to go with something else a bit different that what's been done before
I bought a Porsche G96 6 speed and a GM LF3 Twin turbo V6 to drop
in, Nobody has done this combo to my knowledge, there has been a LFX swapped D here mentioned on this forum but no pics of finished proof. This engine is based on that same GM 60 degree "high Feature v6" made from 09 to now. 3.6 Liter DOHC 24 V, Direct fuel injection, VVT on all cams, water-air intercooler in the manifold.
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/3c8716b4-c355-416b-a5aa-ef79ebad2085.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/a8a4b343-87c3-477c-8850-650808071e9c.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/abfbd72b-7d1c-465a-87d0-de2063baab47.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/bec870b7-d5e9-482f-b571-d660e7e2a510.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/78959025-0b80-46ed-ab15-260d1f4d9cb6.jpg
I swapped in a 5th gen Camaro LFX into a 1986 Maserati Biturbo as a side project for a customer a few years back. 330hp and 300 tq and revs to 7k all day. I Really like the power and sound of that engine, they are cheap and can be durable if you change the oil and don't put a ton of miles on them.
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/e967579d-77bf-4d92-9b51-b11d843f046d.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/4cab4c0b-7f1f-4992-bd6f-de42a4365ad0.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/3a4d1214-c124-4d73-a01a-2ac68735448e.jpg
The LF3/4 is a stronger version made for boost in the CTS V sport and XTS V sports. 430hp isnt bad. Unfortunately its its heavier than I thought and
will add over 100lbs to the rear, Also I was told by Kennedy adapters that they made and adapter plate for that engine to the Porsche transmission until I bought all the parts and went to order
that adapter they said actually no We will not make you one as there are too many over lapping fasteners.
SOOOO, I just have to chop and weld a GM bellhousing onto the Transaxle myself.
That's basically where I am with this project now. Really hoping it will fit into the Delorean after I have the drivetrain assembled. basic measurements says it should but you
never really know until you mock it up.
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/e1201a6c-3b62-43c8-b007-4ab89524a8bb.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/eb3f2a66-58bd-468d-a5bb-de762d62ba01.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/4b30ca65-82c0-41e2-bd8d-b6a9282c5a04.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/a5982426-25d7-4461-9c49-f986215a9a26.jpg
And thats about caught us up with the Delorean. Ive been playing with some other cars recently, been on a Prewar car kick. Bought my first American car: 1930 Ford Model A that I put a BMW
M54 3.0L into, its been pretty fun.
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/9359d804-74c6-4ce7-a71a-330639125185.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/a6157841-63c9-43f7-89ff-9d47523f75cf.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/53ebf24a-a7c3-4b4b-8d04-ff049f9a6957.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/152e2dd7-59c6-4597-8cf3-c8d7134d5f91.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/019ae67c-ce7e-4a98-94ce-3c6c0e063a38.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/e9dd7bfd-47ec-4a0f-a48a-2465d87e0f1f.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/103b7e1a-7ce0-4eeb-a22f-7f65c9ceaa30.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/717aea35-6f45-449f-a5f8-23f5aacf8ae6.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/16028616-a425-4f33-b60d-54bf27592a8e.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/a724020d-a3b2-496c-b1c8-b4dde5f75edb.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/ff32a52d-b0d9-4848-9f95-9a04d0facbc3.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/6c40a8fe-6e3f-4cc0-8e2b-570f36212936.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/28a086dc-2f0e-4ea1-8ea8-653f4b9f1a84.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/af1a715a-3819-4f2f-bc7c-5a7513755721.jpg
But I also wanted something even older:
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/8254db2b-add9-4a05-b589-d9e102d78843.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/9c90b999-fe62-46a2-95ed-1fc16904d0db.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/77fd76f8-7315-4869-9ce8-0b274ce46c97.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/03a5bd12-83ef-4b35-9ed2-4bb30213b199.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/d8a52d72-46ea-4d31-8bbf-3c1d3e63dc77.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/c1b6bf7d-4711-4bb3-abdc-65a38a8bc1d0.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/a26b9c36-fedc-4660-a745-e75514a6a86e.jpg
https://hosting.photobucket.com/426414d7-a640-4aac-81b9-07d80d669ebe/c4663598-d52c-4dd8-9cce-65635cb40e23.jpg
yeah ive been busy!
Thanks for looking!
ssdelorean
09-02-2025, 11:02 AM
Another reason for lack of posts is as we have all seen the sad truth that car forums are dying off fast, I really hate that Facebook did that,
its an awful format that wont have any good records for the future, its all about showing off and arguing about current trends and issues.
Id like to see this platform going as long as it can.
Agree.
FB is a horrible format for any club/hobby where you need to document or find information.
Long live the forums.
Get off my lawn. :-)
Love the Model A. Great stance & window AC unit.
Bitsyncmaster
09-02-2025, 12:10 PM
Agree.
FB is a horrible format for any club/hobby where you need to document or find information.
Long live the forums.
Get off my lawn. :-)
Love the Model A. Great stance & window AC unit.
I second that. It's a shame it's so hard for owners to get to be a member on this forum. I wish there was an email we could send about a new owner to get verified.
ssdelorean
09-02-2025, 12:55 PM
I second that. It's a shame it's so hard for owners to get to be a member on this forum. I wish there was an email we could send about a new owner to get verified.
I have a couple Detroit owners who said they are waiting approval here.
Timeless
09-03-2025, 10:06 AM
Agree.
FB is a horrible format for any club/hobby where you need to document or find information.
Long live the forums.
Get off my lawn. :-)
Love the Model A. Great stance & window AC unit.
Agreed. Stay off my lawn!
Helirich
09-07-2025, 12:09 PM
Good update! Please keep us updated in the future.
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.