Log in

View Full Version : clogged injector on my 03 S10?



timothymoore
07-13-2012, 11:41 AM
truck started running like crap on the way home last night. runs ok at highway speeds but when at idle the motor is shaking like crazy.i scanned it and i have a cylinder 4 misfire. im beginning to think i have a clogged injector.gonna see if autozone has a injector cleaner i can rent to clean them.

Dangermouse
07-13-2012, 11:49 AM
Do you have coil packs?

On my old minivan, I had the same symptoms and code description and it was the coil-pack (it was a common 6-pack on that car rather than individual coil packs I have had on other cars)

$70 and running like new.

timothymoore
07-13-2012, 11:53 AM
it has one main coil powering the distributor. all plugs wires , rotor and cap are good and new. i thought it was the filter , im gonna change it later today and see if it helps. but i checked fuel pressure and it is good.

Ron
07-13-2012, 12:11 PM
Do you have a stethoscope?

timothymoore
07-13-2012, 12:13 PM
nope. i thought about swapping plugs just to confirm it isnt them although i know it isnt

Ron
07-13-2012, 12:23 PM
Try taking a long extension and holding it right on an injector and your ear while plugging & un-plugging the injector to see if it is working.
....do this on another cylinder that you know is working first to learn the sound change and distinguish it from all of the other ticky-tick sounds the engine makes ;-)

If in doubt, swap with another.

timothymoore
07-13-2012, 12:34 PM
i will do that when i get the filter changed, and i think i will put some sea foam in it to help a little.

Ron
07-13-2012, 12:43 PM
I always viewed it as a preventative (works well but usually used too late)... but it is one of the very few things that comes in a can that IMO isn't pure snake oil.

DMCVegas
07-13-2012, 03:03 PM
Try taking a long extension and holding it right on an injector and your ear while plugging & un-plugging the injector to see if it is working.
....do this on another cylinder that you know is working first to learn the sound change and distinguish it from all of the other ticky-tick sounds the engine makes ;-)

If in doubt, swap with another.

If it's a 4.3 Vortec V6, that's not gonna work. Take a look:

http://ecx.images-amazon.com/images/I/419KOo0PenL.jpg

The Vortec uses what's called a "spider" to distribute the fuel to each injector. Imagine an evolved K-Jetronic where the Frequency Valve is intergrated into the Fuel Distributor. It's a CIS system. There are no individual solenoids for the injectors.

SeaFoam and other cleaners are nice and all, but you really need something more powerful that doesn't get diluted at all by other fuel in the tank. Modern Fuel Injection systems have cleaning ports on them. Little schrader valves to connect equipment to. Specifically a hose with a valve and a pressure gauge that you connect a pressurized can of fuel injector cleaner to. Pull the fuse for the fuel pump, connect the hose and canister, dial in the factory spec fuel pressure with the valve and gauge, and run the engine until it burns through all of the cleaner and dies. Disconnect, replace the fuse, and you're good to go.

You may or may not resolve the issue admittedly if you've got a bad injector. The good news is that you'll clean the rest and the new one just pops right in to the spider and the manifold. Otherwise this may very well take care of your problem. Otherwise if it's just gunk, this should clean everything out and get it running again. It's safe for catalytic convertors, and is probably a maintenance procedure you'll want to run on your EFI cars every once in a while anyways.

Ron
07-13-2012, 04:39 PM
If it's a 4.3 Vortec V6, that's not gonna work.
...
It's a CIS system.
...


Good point!

I should of thought of that since I actually have both, wife's 4.3 Blazer and a 2.2 Pickup.
I saw "cylinder 4" and...you know...;-)

Rereading...He definitely has a 4.3 since the 2.2 has multiple coils...
Actually not CIS, but SCPI (Sequential Central Port Injection.)

Makes swapping even easier ;-)

timothymoore
07-20-2012, 07:47 PM
update: this is what ive replaced and fixed so far. some needed replaced and some i did in hopes of fixing the random misfire:

plugs
wires
cap
rotor
ignition control module (fixed the cylinder 4 misfire)
Ignition coil
Tensioner assemply
serpentine belt

I fixed/replaced all of the those items and yet i still have a random misfire code popping up and the truck has very little power until i get going a decent speed. as soon as i hit the pedal the ses light blinks and then stays solid after i get going and when i scan it all that pops up is a random misfire.also at idle it fluctuates from 500 down to 400 rpms then back up to 500 repeatedly. i do have onequestion though. i have a bad intake gasket as well as no cat (cut it off after it plugged up) could one of these if not both cause a misfire? ive done what i think i can do and im boggled right now as to what it is.

Ron
07-20-2012, 11:25 PM
i have a bad intake gasket as well as no cat (cut it off after it plugged up) could one of these if not both cause a misfire?
Cat missing, no. Intake gasket, ABSOLUTELY!

Also, once you get the misfires straightened out, your SES light is going to come on the first time you take it for a good long ride -- Removing the cat will throw off the the down stream O2 signal causing the ECU to throw a trouble code. You can not get away with simply removing/unplugging it. Ignoring it means failing emission tests and "performance" problems. PM me your email and I will tell you how to get around the problem with ~$10 worth of parts if you want.

lorentbj
07-21-2012, 12:07 AM
I believe you first diagnoses of a stuck inj. is correct.I believe cleaning will not unstick it.If you can not see your injs. you have the spider system shown earlier.It is inside the plastic cover.If you change one you might want to change all injs. You will also want to replace fuel pressure regulator that is part of spider. If you go in there for the first time you should have someone to help that has done this before.Also take care when installing plug wires on drivers side of engine as the numbering on cap may not be in order like the passenger side is.
Good luck and let me know how it goes. bob

timothymoore
07-21-2012, 12:50 PM
I believe you first diagnoses of a stuck inj. is correct.I believe cleaning will not unstick it.If you can not see your injs. you have the spider system shown earlier.It is inside the plastic cover.If you change one you might want to change all injs. You will also want to replace fuel pressure regulator that is part of spider. If you go in there for the first time you should have someone to help that has done this before.Also take care when installing plug wires on drivers side of engine as the numbering on cap may not be in order like the passenger side is.
Good luck and let me know how it goes. bob

i beleive it is the intake. i inspected it yesterday and it is getting worse than what it was before. before it was just in front by the water pump, but it has now spread over to the driver side of the intake. i guess i got a intake gasket to buy and a project to do in the next couple days.

DMCVegas
07-22-2012, 03:52 AM
update: this is what ive replaced and fixed so far. some needed replaced and some i did in hopes of fixing the random misfire:

plugs
wires
cap
rotor
ignition control module (fixed the cylinder 4 misfire)
Ignition coil
Tensioner assemply
serpentine belt

I fixed/replaced all of the those items and yet i still have a random misfire code popping up and the truck has very little power until i get going a decent speed.

I honestly don't want to be a dick, and my intentions here are not to offend or hurt anyone's feelings. However I do believe that this post has a great deal of merrit to it to serve as an example of others.

When it comes to Car Repair, be it the restoration of a Classic, or the Maintenance of an everyday driver, this is the prime example of why cars so quickly become money pits that shatter people's dreams. You cannot unleash a "scorched earth" repair on a car and just expect it to fix your problems 100% of the time. But 100% of the time when you perform massive repairs you do in fact waste money.

As an example, if your clothes were bloody you wouldn't just change clothes. You'd go ahead treat the wound that is causing the bleeding. And in the process of that you wouldn't still yet simply wear a tourniquet and pop pain pills for the rest of your life. You would of course figure out what has caused the bleeding and in turn address the wound itself and treat it accordingly. Same thing if a pipe burst in your basement. Would you simply install a sump pump to prevent it from flooding? Or would you just go ahead and fix the pipe? Redundant questions I know, but you all get my point. Especially here. If you've swapped out these items, the root problem is still here and the truck WILL throw error codes again just as soon as that Spark Plug either fowls up again or the new ECU finishes it's testing and gets to throw that code one more time as it recognizes that same problem. You haven't "fixed" the error code, but have just sent it away for a while.

The Blazer's SCPI and the DeLorean's K-Jetronic are very similar in their troubleshooting for this type of issue. The two similar items here are the symptoms of the engine & the goals that individual troubleshooting methods use. The only differences are of course the specialized tools and the OBD-II system that assists us in troubleshooting. It does NOT always pinpoint the specific issue, that is impossible. But it does help quite a bit. But even then it's not totally necessary here. The advantage that it does present of course is that now you have narrowed it down to a specific cylinder.

If you have accurate knowledge of a specific part that you know for a fact is bad, replace the thing. Unless any other parts fail testing, don't replace them. The part that I speak of here is that gasket. Get it fixed. I don't however think that it is the specific issue. Maybe I'm wrong, but none of us will know until it's fixed. The reason I say that is that I believe that if that was the issue, you should be getting an error code which states that the Cylinder Bank which #4 is apart of is running a lean condition.

Most likely the issue here is #4's Fuel Injector. But still you can't just go about swapping damn parts left and right. You need to continue troubleshooting to see what the issue is. In this case it's either the Injector Itself that is clogged, or the Distributor that is not properly allocating fuel. To troubleshoot that of course what you really need is a set of graduated Cylinders, or at the very least some Mason Jars. Poke holes in the tops of the jars to hold the injectors, and the trip the fuel pump. The two things that you want to look for are Spray Patterns from the injectors, and Flow Rates. By the time you kill power to the pump, you should have the same amount of fuel in each jar. If one of the jars is radically different in it's final fluid amount, OR you witness that particular injector having a poor spray pattern, swap injectors on the Spider and see if the issue remains with the injector or the socket that said injector plugs into. That will give you a good idea of what is going on.

Yes, it is possible to clean the injectors and have that resolve your issue if the problem is deposits on the injectors. But you need a specific tool to connect to the schrader valve on the fuel supply line in order to pump that cleaner in there.

This is the stuff you'd need:
http://ww2.justanswer.com/uploads/Micharoe/2010-04-03_024403_cleaner.gif

And this is the tool you need to administer it with:
http://images.drillspot.com/pimages/7426/742682_300.jpg

Is it work? Yes. But it's allot less in time and cost to do this than what you've already done. Especially with tools that you can reuse on your other vehicles, and the achievement of that quick, proper repair.

ccurzio
07-22-2012, 06:04 AM
As an example, if your clothes were bloody you wouldn't just change clothes. You'd go ahead treat the wound that is causing the bleeding.

Sorry to zero in on this, but this is some seriously backwards thinking.

If your clothes are bloody, you dump the body into the shallow grave (after they've told you what you need to know) and then you ABSOLUTELY change clothes, burning the old ones.

Treat the wound? Where's your head, man?

Ron
07-22-2012, 11:18 AM
Sorry to zero in on this, but this is some seriously backwards thinking.

If your clothes are bloody, you dump the body into the shallow grave (after they've told you what you need to know) and then you ABSOLUTELY change clothes, burning the old ones.

Treat the wound? Where's your head, man?
:hysterical:


==================

I don't understand parts of some of the latest responses -- Note he said that replacing the ignition control module fixed the #4 misfire. If all of the parts in the list were changed at the same time (doesn't read that way to me tho..), it would be highly questionable...BUT there is no mention of fuel related parts being disturbed!....(or the condition of #4 spark plug??) I don't see a single injector causing a random misfire AND no other codes being thrown(possible, but unlikely here).

I'm with Vegas except for the #4 injector, 100%, which makes me point to a different tool. I'd fix the gasket because it is definately needed. If that didn't fix it, as I said before, a better scanner is need here. Being able to read which cylinders and their individual misfire counts is invaluable. For example: as said, random misfire only means "2 or more" are missing. Now, how many, which ones, same bank, which bank, are they adjacent cylinders (hmmm vacuum leak)...a very long list of conditions and combinations for misfires alone to help diagnose the problem is missing. As low tech as the term sounds, a "shake and wiggle" test, is on most diagnosis charts for a lot of problems -- you need to monitor the results real time. If you can't afford one spend ~$30 at dealership if you have to.

lorentbj
07-22-2012, 05:28 PM
Cat. converter--What takes out a cat.?I would suggest coolant going through engine or an engine miss caused by unburned fuel.
No one wants to throw away time or money.Most of the parts changed were normal preventive maint.
Yes proper diagnostics is the way to go.Check for vacumn leaks,check compression,and injector output.
On this type of veh. with spider inj.is it possible to do a inj. output test?
thanks,bob

timothymoore
07-23-2012, 12:24 AM
I honestly don't want to be a dick, and my intentions here are not to offend or hurt anyone's feelings. However I do believe that this post has a great deal of merrit to it to serve as an example of others.

When it comes to Car Repair, be it the restoration of a Classic, or the Maintenance of an everyday driver, this is the prime example of why cars so quickly become money pits that shatter people's dreams. You cannot unleash a "scorched earth" repair on a car and just expect it to fix your problems 100% of the time. But 100% of the time when you perform massive repairs you do in fact waste money.

As an example, if your clothes were bloody you wouldn't just change clothes. You'd go ahead treat the wound that is causing the bleeding. And in the process of that you wouldn't still yet simply wear a tourniquet and pop pain pills for the rest of your life. You would of course figure out what has caused the bleeding and in turn address the wound itself and treat it accordingly. Same thing if a pipe burst in your basement. Would you simply install a sump pump to prevent it from flooding? Or would you just go ahead and fix the pipe? Redundant questions I know, but you all get my point. Especially here. If you've swapped out these items, the root problem is still here and the truck WILL throw error codes again just as soon as that Spark Plug either fowls up again or the new ECU finishes it's testing and gets to throw that code one more time as it recognizes that same problem. You haven't "fixed" the error code, but have just sent it away for a while.

The Blazer's SCPI and the DeLorean's K-Jetronic are very similar in their troubleshooting for this type of issue. The two similar items here are the symptoms of the engine & the goals that individual troubleshooting methods use. The only differences are of course the specialized tools and the OBD-II system that assists us in troubleshooting. It does NOT always pinpoint the specific issue, that is impossible. But it does help quite a bit. But even then it's not totally necessary here. The advantage that it does present of course is that now you have narrowed it down to a specific cylinder.

If you have accurate knowledge of a specific part that you know for a fact is bad, replace the thing. Unless any other parts fail testing, don't replace them. The part that I speak of here is that gasket. Get it fixed. I don't however think that it is the specific issue. Maybe I'm wrong, but none of us will know until it's fixed. The reason I say that is that I believe that if that was the issue, you should be getting an error code which states that the Cylinder Bank which #4 is apart of is running a lean condition.

Most likely the issue here is #4's Fuel Injector. But still you can't just go about swapping damn parts left and right. You need to continue troubleshooting to see what the issue is. In this case it's either the Injector Itself that is clogged, or the Distributor that is not properly allocating fuel. To troubleshoot that of course what you really need is a set of graduated Cylinders, or at the very least some Mason Jars. Poke holes in the tops of the jars to hold the injectors, and the trip the fuel pump. The two things that you want to look for are Spray Patterns from the injectors, and Flow Rates. By the time you kill power to the pump, you should have the same amount of fuel in each jar. If one of the jars is radically different in it's final fluid amount, OR you witness that particular injector having a poor spray pattern, swap injectors on the Spider and see if the issue remains with the injector or the socket that said injector plugs into. That will give you a good idea of what is going on.

Yes, it is possible to clean the injectors and have that resolve your issue if the problem is deposits on the injectors. But you need a specific tool to connect to the schrader valve on the fuel supply line in order to pump that cleaner in there.

This is the stuff you'd need:
http://ww2.justanswer.com/uploads/Micharoe/2010-04-03_024403_cleaner.gif

And this is the tool you need to administer it with:
http://images.drillspot.com/pimages/7426/742682_300.jpg

Is it work? Yes. But it's allot less in time and cost to do this than what you've already done. Especially with tools that you can reuse on your other vehicles, and the achievement of that quick, proper repair.

ive used those tools before at school, but do not have access to them outside of school.

DMCVegas
07-23-2012, 07:08 PM
Cat. converter--What takes out a cat.?I would suggest coolant going through engine or an engine miss caused by unburned fuel.

And what is your suggestion based upon? Lead from leaded fuel will cake and clog up a cat, raw gasoline can melt the honeycomb from overabundance of chemical reactions (as well as wash the cylinders out). While glycol from a blown headgasket *might* lower the efficiency, there is no way that it would clog it let alone lead to an issue like this. It would of course contaminate the O2 sensors and cause poor fuel economy, but not bog the whole engine down as described. Again you have to actually troubleshoot and follow common sense as well as diagnostic procedures, and not just continually guess as to what might be the problem.



No one wants to throw away time or money.Most of the parts changed were normal preventive maint.

http://blackjeezus.files.wordpress.com/2010/07/carl-facepalm.png

Replacing perfectly good parts is NOT "Preventative Maintenance", rather it simply put is the lie that either a bad mechanic or YOU tell yourself in order to justify the expensive mistake. You can do an oil change 500 miles and call it preventative maintenance too, and it's just as dumb. The "Preventative" part of preventative maintenance is supposed to mean that the entire goal of the "maintenance" is acheived to prevent a mechanical failure of whatever machinery you're working on. It does not mean that you are taking care of an inevitable task and are preventing yourself from doing this again in the future. Like that oil change, all you're doing is resetting the clock as to when you've got to inevitably do the work again. Only replace what you need WHEN you're supposed to replace it. As I said this kind of haphazard, reckless troubleshooting methods are what cause so many projects to become nightmarish money pits.



Yes proper diagnostics is the way to go.Check for vacumn leaks,check compression,and injector output.
On this type of veh. with spider inj.is it possible to do a inj. output test?
thanks,bob

Read my post, and others again and you'll have your answers.

DMCVegas
07-23-2012, 07:10 PM
ive used those tools before at school, but do not have access to them outside of school.

Such is the life of a mechanic to buy tools.

They're only about $125 or so on average.

timothymoore
07-24-2012, 12:03 AM
Such is the life of a mechanic to buy tools.

They're only about $125 or so on average.

now that i just started my new job, i can get that tool. ive been unemployed since early september of '11