TestPoint
07-16-2012, 10:45 AM
Please forgive the intrusion of a Volvo nut but I have discovered that the DMC folks know a lot more about the B28F engine than the Volvo dudes. The PRV is not held in high regard 'over there'. Most prefer the tractor engines.
Long story but I found an '81 Volvo Bertone Coupe in a barn in TN with 25k original miles on it. The elderly owner had attempted to get it running after 19 years in storage after his wife died. A local tune up shop worked extensively on it without success. They cleaned the rusty fuel tank, installed a tank pump, a pressure pump, filter, spark plugs, plug wires, distributor cap and rotor and generally took everything apart and put it back together. The 'take apart' included the fuel distributor which then leaked.
http://i772.photobucket.com/albums/yy4/tporterellijaycom/Volvo%20Bertone/P6220932.jpg
I bought it in non-running condition and have succeeded in getting it running . . . but not well.
Found corroded fuses and the relay contacts in both the pump relay and Lambda System relay were corroded and erratic.
Found several vacuum leaks in cracked and broken 31 year old hoses and connectors, the gasket between the upper and lower air plate assembly was only half installed, the 'ram horn' connection to the intake manifold was connected with bolts too long and therefore not sealing. Bolts were broken and washers missing all over the top of the engine. Found the spark advance at 10 degrees before TDC. In short, Elroy, the Master Oil Change Technician that had worked on the car to the tune of over $2,000 left a mess. I replaced the O2 sensor which was dead, had the fuel distributor rebuilt, replaced the Lambda Module which was the wrong one for the car, tested the injectors, tested the line pressure, and the control pressure, and set the CO adjustment using the dwell settings found on this forum. Oiled the distributor wick, which was dry as a bone, and set the ignition timing to specs. Found the spark coil resistor out of spec and jumped that.
The line pressure is 72 psi, the cold engine control pressure is 38 psi and rises to 52 psi in 5 minutes as it should. The cold high idle drops at 2 min, 35 seconds, the 066 Control Pressure Regulator loses its vacuum at about the 125 degree spec. Dwell at idle is 30-40 on the 4 cyl scale and drops to 28-32 at 3k rpm. The Frequency Valve seems to operate correctly as it is buzzing and passes fuel back to the fuel return line under control of the Lambda dwell. The return line is clear. Ignition advance is 10 degrees at idle and advances to 30+ degrees at 2k rpms. The exhaust does not seem restricted.
I have not figured out how to view the control pressure while driving but it does not change when revving to stall speed.
The engine starts easily, runs smoothly, will rev to redline, runs to torque converter stall speed (2300 rpm) but bogs on throttle while driving it. What am I missing? Any suggestions?
Thanks for any consideration of an alien to the forum.
Long story but I found an '81 Volvo Bertone Coupe in a barn in TN with 25k original miles on it. The elderly owner had attempted to get it running after 19 years in storage after his wife died. A local tune up shop worked extensively on it without success. They cleaned the rusty fuel tank, installed a tank pump, a pressure pump, filter, spark plugs, plug wires, distributor cap and rotor and generally took everything apart and put it back together. The 'take apart' included the fuel distributor which then leaked.
http://i772.photobucket.com/albums/yy4/tporterellijaycom/Volvo%20Bertone/P6220932.jpg
I bought it in non-running condition and have succeeded in getting it running . . . but not well.
Found corroded fuses and the relay contacts in both the pump relay and Lambda System relay were corroded and erratic.
Found several vacuum leaks in cracked and broken 31 year old hoses and connectors, the gasket between the upper and lower air plate assembly was only half installed, the 'ram horn' connection to the intake manifold was connected with bolts too long and therefore not sealing. Bolts were broken and washers missing all over the top of the engine. Found the spark advance at 10 degrees before TDC. In short, Elroy, the Master Oil Change Technician that had worked on the car to the tune of over $2,000 left a mess. I replaced the O2 sensor which was dead, had the fuel distributor rebuilt, replaced the Lambda Module which was the wrong one for the car, tested the injectors, tested the line pressure, and the control pressure, and set the CO adjustment using the dwell settings found on this forum. Oiled the distributor wick, which was dry as a bone, and set the ignition timing to specs. Found the spark coil resistor out of spec and jumped that.
The line pressure is 72 psi, the cold engine control pressure is 38 psi and rises to 52 psi in 5 minutes as it should. The cold high idle drops at 2 min, 35 seconds, the 066 Control Pressure Regulator loses its vacuum at about the 125 degree spec. Dwell at idle is 30-40 on the 4 cyl scale and drops to 28-32 at 3k rpm. The Frequency Valve seems to operate correctly as it is buzzing and passes fuel back to the fuel return line under control of the Lambda dwell. The return line is clear. Ignition advance is 10 degrees at idle and advances to 30+ degrees at 2k rpms. The exhaust does not seem restricted.
I have not figured out how to view the control pressure while driving but it does not change when revving to stall speed.
The engine starts easily, runs smoothly, will rev to redline, runs to torque converter stall speed (2300 rpm) but bogs on throttle while driving it. What am I missing? Any suggestions?
Thanks for any consideration of an alien to the forum.