Log in

View Full Version : Looking into a SS engine cover...



adam_knox
08-08-2012, 11:26 AM
Okay, I think I have it figured out how I want to "customize" my future Delorean! :cool: First of all, I really really like the look of the prototype without the louvre. So that's going to come off. My real idea is to replace the black engine cover with a brushed stainless steel one (to match the grain on the car). The grates would then either be the stainless after-market inserts or the stock black ones (to sort of tie in the black trim by the windows).
Does anyone see any practical reasons this is a terrible idea? Any input would be appreciated.

Things I need to investigate: :reading:
1. Cost of a stainless panel and someone to cut/fabricate it
2. How to best match the brushing on the rest of the car
3. Water and debris entering engine bay...would the grates need to be moved to other locations? How much risk is there for excessive corrosion/malfunction without the louvre to deflect the elements?
4. Ability of shocks able to hold up cover
5. Heat retention and light reflection

Jimmyvonviggle
08-08-2012, 11:52 AM
I think the louvres actually serve a function besides the look. Anyone please correct me if I am wrong but don't the louvres actually help with the fuel consumption by increasing the aerodynamics.

I personally think it finishes the car off nicely but to each his own.

thirdmanj
08-08-2012, 12:04 PM
They do. They minimize drag, thus increasing mpg.

adam_knox
08-08-2012, 12:40 PM
Yeah, to my understanding its slightly a bit louder with the louvre off in the passenger compartment and the engine may run slightly warmer. I'm fine with the slight decrease in mpg, maybe if I add a mega huge spoiler it'll counter that! :jk: I do believe the louvres were added solely for cosmetic reasons (there was a discussion about it from the old site where this was mentioned i think).

thirdmanj
08-08-2012, 01:00 PM
Well it wasn't just for cosmetic reasons. The mpg increase was a deciding factor I'm sure.

BTTF-1
08-08-2012, 01:14 PM
SS is Awesome!

Ed:notworthy::wave2::notworthy:

Spittybug
08-08-2012, 01:22 PM
Not stainless, but painted stainless. Right now it's plexiglass, but I found a guy that can provide tempered glass to shape at a good price. Shows off the new EFI engine and manifold work nicely (this is an old shot however). Louvers chopped below second row. Maintains good air flow over car. It's homage to Giorgetto Giugiaro (http://en.wikipedia.org/wiki/Giorgetto_Giugiaro) and one of his other designs, the Maserati Merak. http://commons.wikimedia.org/wiki/File:Maserati_Merak_silver_rear.jpg

No good louvers or engine covers were butchered for this modification thanks to James at DMCH having a couple of busted up ones that were beyond repair.

Getting a stainless cover made with the required bends, creases and openings would be expensive...

Jacko
08-08-2012, 01:44 PM
Soon after getting my first Delorean I met another new owner who had removed the louvers ... he said he wanted his car to 'stand out'. I thought ... "Good God, man, doesn't it stand out enough just being a Delorean?!" The louvers is one of my favorite design elements of the D.

Once I made an engine cover for a '72 Pantera I had out of 1/4" plexiglas ... didn't last long. The heat from that 351 Cleveland soon melted it.:screwy:

adam_knox
08-08-2012, 02:44 PM
Thanks for the pics and sharing your process Spittybug! Looks great! Thirdmanj, I'm sure your correct that there were multiple considerations, including mpg, when DMC decided to add the louvres. Jacko, I wish I could say I like the louvres, but that is honestly the one thing I don't like about the cars... Good thing I wasn't on the final design team, woulda tanked sales with my "style" sense!:tongue2: I sort of equate it to the look of the Lotus Espirit without the spoiler.

dmc6960
08-08-2012, 03:06 PM
Well it wasn't just for cosmetic reasons. The mpg increase was a deciding factor I'm sure.

I think it was just for cosmetic reasons. All the other benefits (which ARE there) were a bonus.

Trying to find the thread a while back where we discussed it all in detail, I think it was back on .com.

So let me see if I can summarize from memory...


Someone posted about higher engine temperatures when driving around with the louvers off.

People tended to agree that the louvers had an added function (never mentioned intentional or not!) to cool the engine by extracting heat.

Bill argued that they perform no such function and are there solely because JZD wanted them.

People also added the fact that they improve the aerodynamics of the car thus increasing fuel economy.

Bill argued that they perform no such function and are there solely because JZD wanted them.

People tried discussing with Bill that while the louvers may not have been added for the purpose of gaining those effects, they are still present.

Bill argued that they perform no such function and are there solely because JZD wanted them, provided documented source for this statement.

Someone ran some DeLorean outlines, with and without louver cross-section through some CFD (Computational Fluid Dynamics) programs and posted the results showing how much less the drag is with the louvers present.

Bill may have argued his point one more time.

.com crashed.

adam_knox
08-08-2012, 03:29 PM
DMC6960, that's what I remember too for the most part. I didn't remember reading about the CFD or could attribute the claims and evidence of the louvres being added per JZD request by any particular member, but I'm pretty sure someone had quoted a document or two. Such a shame the .com site went down and we lost all that. Its like we're a bunch of people with conversing with memory problems, repeating topics without recalling what was said or by whom or knowing the conversation had already taken place before!

thirdmanj
08-08-2012, 03:31 PM
I think it was just for cosmetic reasons. All the other benefits (which ARE there) were a bonus.

Trying to find the thread a while back where we discussed it all in detail, I think it was back on .com.

So let me see if I can summarize from memory...


Someone posted about higher engine temperatures when driving around with the louvers off.

People tended to agree that the louvers had an added function (never mentioned intentional or not!) to cool the engine by extracting heat.

Bill argued that they perform no such function and are there solely because JZD wanted them.

People also added the fact that they improve the aerodynamics of the car thus increasing fuel economy.

Bill argued that they perform no such function and are there solely because JZD wanted them.

People tried discussing with Bill that while the louvers may not have been added for the purpose of gaining those effects, they are still present.

Bill argued that they perform no such function and are there solely because JZD wanted them, provided documented source for this statement.

Someone ran some DeLorean outlines, with and without louver cross-section through some CFD (Computational Fluid Dynamics) programs and posted the results showing how much less the drag is with the louvers present.

Bill may have argued his point one more time.

.com crashed.

How does that prove your idea that they are just for cosmetic reasons. Anyone have something more solid than opinions to back up that claim? Because right now there's more for the argument of function. Seems to me with all the function, the cosmetic is the bonus.

dmc6960
08-08-2012, 03:34 PM
I didn't remember reading about the CFD or could attribute the claims and evidence of the louvres being added per JZD request by any particular member

It wasn't old DMC documents with the CDF (did they even that that back in 1980?). It was a member on DMCTalk that plugged the DeLorean cross section into a 2D CFD program and got the results and posted them here.

There was real wind-tunnel testing with the car back in the late 70's and early 80's. After the louvers were added there must have been positive comments from the whole wind tunnel team.

dmc6960
08-08-2012, 03:35 PM
How does that prove your idea that they are just for cosmetic reasons. Anyone have something more solid than opinions to back up that claim? Because right now there's more for the argument of function. Seems to me with all the function, the cosmetic is the bonus.

Not *my* idea that they were added for cosmetic reasons. It was Bill's. For which he did provide substantial evidence to the matter, but I dont remember what that was.

Totally 80s
08-08-2012, 03:35 PM
I think it was just for cosmetic reasons. All the other benefits (which ARE there) were a bonus.

Trying to find the thread a while back where we discussed it all in detail, I think it was back on .com.

So let me see if I can summarize from memory...


Someone posted about higher engine temperatures when driving around with the louvers off.

People tended to agree that the louvers had an added function (never mentioned intentional or not!) to cool the engine by extracting heat.

Bill argued that they perform no such function and are there solely because JZD wanted them.

People also added the fact that they improve the aerodynamics of the car thus increasing fuel economy.

Bill argued that they perform no such function and are there solely because JZD wanted them.

People tried discussing with Bill that while the louvers may not have been added for the purpose of gaining those effects, they are still present.

Bill argued that they perform no such function and are there solely because JZD wanted them, provided documented source for this statement.

Someone ran some DeLorean outlines, with and without louver cross-section through some CFD (Computational Fluid Dynamics) programs and posted the results showing how much less the drag is with the louvers present.

Bill may have argued his point one more time.

.com crashed.


That pretty much sums up 90 percent of the posts on dmctalk last year. 8)

Bitsyncmaster
08-08-2012, 03:55 PM
Getting a stainless cover made with the required bends, creases and openings would be expensive...

I've seen a custom SS louver. I think his asking price was $5000. It was a good build job and probably a lot more work than the engine cover.

Dracula
08-08-2012, 03:55 PM
I've tried with and without the louvres on the car and I saw a 7mpg decrease without them and around a 10 degree increase in operating temperature. To me, that negated any potential aesthetic benefit that COULD have been gained by removing them. Note, that I drove the car from Minnesota to Wisconsin without them, so it was a full test under the best conditions.

thirdmanj
08-08-2012, 05:28 PM
I've tried with and without the louvres on the car and I saw a 7mpg decrease without them and around a 10 degree increase in operating temperature. To me, that negated any potential aesthetic benefit that COULD have been gained by removing them. Note, that I drove the car from Minnesota to Wisconsin without them, so it was a full test under the best conditions.

Thanks for chiming in here man. I seem to recall you and I discussing this in another thread.

adam_knox
08-08-2012, 07:23 PM
Woah, 7mgp? :umm: A'ight, looks like I'll have to definitely look into this a bit after I can do some testing and number crunching on my own next year. If this was 1997, I'd say, heck, what's a few more cents in gas... See, this is why you guys are great; its like a giant pool of beta tester! Thanks for the input guys.

Dracula
08-08-2012, 08:29 PM
It may not be exactly 7, but it was a shockingly drastic change that was right around seven; + or - 1 MPG. I didn't expect it to be that much; otherwise, I did like the improved visibility and look of the car without them.

SamHill
08-09-2012, 03:53 PM
Not *my* idea that they were added for cosmetic reasons. It was Bill's. For which he did provide substantial evidence to the matter, but I dont remember what that was.

I think it was a quote from someone who was actually there. Maybe Collins. JZD saw the development of the Esprit that was going on at the same time and said, "I want that on my car." It really is as simple as that.

Shep
08-09-2012, 10:49 PM
Not sure who's thinking what exactly, but I wouldn't think the prototype that's missing the louvers was intended to be the final design. The rear quarter panels still have the D-pilliar that slopes from the roof to the rear fascia, and frankly it looks unfinished without the louvers to even it out. If they had not gone with the louvers, I'd think they may have taken an approach similar to the FlatOut appearance of the DeLorean, with glass wrapping around the entire back instead of the glass. I can't think of a reason JZD would want to have stainless steel sticking up on the sides for no reason, and nothing supporting it aesthetically in the middle.

Think of it this way: without the D-pilliar and louvers, the DeLorean would essentially be a stainless steel gull-winged pickup truck with an unusable bed.

adam_knox
08-09-2012, 11:33 PM
EMDF
Not sure who's thinking what exactly, but I wouldn't think the prototype that's missing the louvers was intended to be the final design. The rear quarter panels still have the D-pilliar that slopes from the roof to the rear fascia, and frankly it looks unfinished without the louvers to even it out. If they had not gone with the louvers, I'd think they may have taken an approach similar to the FlatOut appearance of the DeLorean, with glass wrapping around the entire back instead of the glass. I can't think of a reason JZD would want to have stainless steel sticking up on the sides for no reason, and nothing supporting it aesthetically in the middle.
Well, to me, the Lotus Espirit has a similar design without the louvres (albeit they have a spoiler on the back end). I'm no expert on the history of the Delorean, but why would they show the prototype to the press without the design being done? Is that common to have the car released to the press without being finished? I mean, its one thing to make design changes, its another to just not finish it and add the louvre if it was a key element to the rear end's appearance or function - i.e. air flow. I'm just asking because I have no clue. Do we know if there there was a sketch from the design phase that shows it without the louvre? Is so, do we know when it was superceded by a louvre added?


without the D-pilliar and louvers, the DeLorean would essentially be a stainless steel gull-winged pickup truck with an unusable bed.
I disagree. It would be the world's coolest El Camino! 8)


I apologize in advance for rehashing a topic that was discussed on the .com site. At least we'll have a thread to refer back to now!

Shep
08-10-2012, 07:05 PM
Well, to me, the Lotus Espirit has a similar design without the louvres (albeit they have a spoiler on the back end). I'm no expert on the history of the Delorean, but why would they show the prototype to the press without the design being done? Is that common to have the car released to the press without being finished? I mean, its one thing to make design changes, its another to just not finish it and add the louvre if it was a key element to the rear end's appearance or function - i.e. air flow. I'm just asking because I have no clue. Do we know if there there was a sketch from the design phase that shows it without the louvre? Is so, do we know when it was superceded by a louvre added?If I recall correctly, the prototypes made by Giorgio Giugiaro had louvers in the back. I haven't seen pictures in a while though, so take that with a grain of salt. As for why they might skip the louvers, that prototype was more of a PR prototype, being shown to press, dealers, investors, etc. Maybe the louvers weren't the final design, or there were problems with them, or there were mechanical concerns and they needed quick access to the engine. Really a lot of reasons why they may not have been included. Again, grain of salt.


I disagree. It would be the world's coolest El Camino! 8)I never said it was a bad thing :wink: Personally, if someone were to do that and put the engine in the front, that'd be kickass :biggrin: If I had Rich W's ambition and time...



I apologize in advance for rehashing a topic that was discussed on the .com site. At least we'll have a thread to refer back to now!Indeed! No need to apologize. :smile:

Getting back on topic for a bit, I do recall someone having stainless steel louvers. I don't know where I saw it or if I could find it again, but if you're looking to do a stainless steel engine cover and are worried about removing the louvers, doing them both in stainless would solve that issue. And it would look a lot better than mix-n-match.

jmpdmc
08-12-2012, 01:58 PM
A local PA guy had some custom stainless louvers made and showed them at a tech session in 2009. Here is a link to pictures and his contact info: http://tinyurl.com/94ty6l3
They looked very nice in person but were heavy.


Jeff

adam_knox
08-12-2012, 02:50 PM
Thanks for the link to the mythical SS louvre everyone was talking about! Looks really sharp! :thumbup:

dvonk
08-12-2012, 08:55 PM
since were on the topic of louvers: VIN 17006 has a stainless louver kit that is made from thin stainless panels cut to fit and bonded to the fiberglass. the solid stainless louvers look cool (awesome craftsmanship!), but i like the look of the black fiberglass border with the kit:

http://dmctalk.org/attachment.php?attachmentid=12482&d=1344815609
12482
(photo courtesy of Brent L.)

adam_knox
08-12-2012, 10:45 PM
Ooh, fancy! Looks nice with the black border. I'm going to have to line the engine cover first with aluminum foil or something to get a visual on what a stainless steel panel would look like surrounded by the black. I've been looking at prices for the stainless steel and so far its not looking too bad ($450-ish for a panel the size of the cover). I'm not sure on the dimensions or needed thickness, but I'd imagine the whole project would cost around $1200. I'm thinking it would maybe take 4 to 5 hours for a metal worker to bend it into shape. Note: I haven't looked into the labor part, but that's my naive guesstimate.

BTW Dvonk, I love your savings meter. Its awesome when it shifts closer to the right! I have a little mental race going with you on which one of us gets one first, but I'm secretly hoping its a tie. :cheers:

dvonk
08-12-2012, 11:11 PM
BTW Dvonk, I love your savings meter. Its awesome when it shifts closer to the right! I have a little mental race going with you on which one of us gets one first, but I'm secretly hoping its a tie. :cheers:

thanks, i like watching it move too. :biggrin:

it wasnt my idea originally, but i liked it, so i started using it as well. and hey, if you are able to get a D before i am, props to you! ill get there eventually. ive waited 16+ years, so a couple more wont kill me. :wink: