PDA

View Full Version : Electrical Question - Non-DeLorean; Ammeter installation



Dracula
10-11-2012, 05:46 PM
I've recently acquired a few gauges from a Junkers Ju 87 and I thought that, for a neat project, I'd hook them up in a spare gauge panel for a car. The only one I'm having some difficulty in figuring out what to do with is the Ammeter. I was thinking that it would be neat to use it to indicate when the cooling fans kick in and so I could see just how many amps they're pulling. I was planning to wire it in to the positive wire leading to the fan and a secondary negative ground bus for all the gauges.

Anyone know any reason why this wouldn't work?

Here's a picture of the gauge for reference:

http://sphotos-a.xx.fbcdn.net/hphotos-snc7/580180_3846178158409_308590107_n.jpg

Bitsyncmaster
10-11-2012, 06:30 PM
If it is a real amp meter you hook it in series with the load. You would need heavy wire so it won't drop a lot of voltage. Measure the resistance across the meter, it should be almost zero ohms.

DMCMW Dave
10-11-2012, 09:14 PM
Anyone know any reason why this wouldn't work?

Here's a picture of the gauge for reference:



Because it is a 30 amp meter on a car that can pull close to 100A?

It also only shows one direction, whereas typical automotive meters are bidirectional so you can see charging current or load current. You could put this one in line with just the loads, but it is still much to small unless you invent a shut to recalibrate it for 100A full scale.

Dracula
10-11-2012, 09:28 PM
Because it is a 30 amp meter on a car that can pull close to 100A?

It also only shows one direction, whereas typical automotive meters are bidirectional so you can see charging current or load current. You could put this one in line with just the loads, but it is still much to small unless you invent a shut to recalibrate it for 100A full scale.

I'm well aware of the limitation of the gauge due to its low amperage; hence why I want to use it to indicate function of a specific system. It's more for novelty than practicality; a sort of fan-is-running indicator, if you will.

The main reason for my interest in such a pursuit is the fact that I think it'll be neat to look at a series of vintage aircraft gauges.

Dangermouse
10-11-2012, 11:24 PM
Is there any rating info on the back of this meter?

I am a bit rusty on WWII German warplane electrical systems, but some panel meters are designed to give full scale deflection with 1A or 5A via a shunt.

For all i know, they had a genny on board and ran all the heavy stuff off AC .

Dracula
10-11-2012, 11:32 PM
Is there any rating info on the back of this meter?

I am a bit rusty on WWII German warplane electrical systems, but some panel meters are designed to give full scale deflection with 1A or 5A via a shunt.

For all i know, they had a genny on board and ran all the heavy stuff off AC .

There's no rating and no information on this gauge. I'll check some of the others, but they are all DC; for a 24v system. Most items can be made to work with a step-up transformer or a capacitor. The only tricky piece, to me, was the Ammeter. I managed to test it through a battery and a series of headlights wired to a battery charger. It pulled 3 amps, but that was enough to get the meter to move.

Bitsyncmaster
10-12-2012, 07:07 AM
Car amp meters were great tools. Wish they still had them. They would be wired to the battery to show both discharge or charging current. So no current would indicate the alternator is powering the car. Always + current would indicate your battery had a shorted cell. Always - current would indicate your alternator is not providing enough output. They would save you getting stuck somewhere if you knew how to read them.

Rich
10-12-2012, 01:57 PM
I'm well aware of the limitation of the gauge due to its low amperage; hence why I want to use it to indicate function of a specific system. It's more for novelty than practicality; a sort of fan-is-running indicator, if you will.....I was planning to wire it in to the positive wire leading to the fan and a secondary negative ground bus for all the gauges....

So, just to be sure you know you have your how-to-install answer; Dave is right, you will insert this ammeter in-line using the wire that feeds both of the cooling fans. All of the fan current needs to run through it. The (+) side of the meter will see the incoming current from the relay and the (-) side is sending current on to the fan motors.

Do NOT wire it to the positive wire leading to the fan and then to any ground. That will short out the fan circuit. And it may fry the ammeter.

You may wish to trial-rig it with the meter wired up near the fans and check the operation at idle with the fans on before you get into serious wiring and mounting work. As noted already, make all of your connections and wiring stout.

DMCVegas
10-12-2012, 05:20 PM
Car amp meters were great tools. Wish they still had them. They would be wired to the battery to show both discharge or charging current. So no current would indicate the alternator is powering the car. Always + current would indicate your battery had a shorted cell. Always - current would indicate your alternator is not providing enough output. They would save you getting stuck somewhere if you knew how to read them.

Yeah, but too much information confuses people and becomes detrimental to the experience. I once knew a DeLorean owner that complained that his car always ran hot because it hovered below 220°F, and water boils at 212°F :eek7:

Explaining the principals how chemical additives and mechanical restrictions can modify the freezing and boiling points did no good. I asked him if his wife's Camry ever ran hot and he said it didn't. I asked him what temperature it normally hovered at, and he said it was in the black and never reached the red.
:mallet:

Explaining that both cars were running at the same temperatures and also the psychological implications of numbers as you can imagine did no better. But it just goes to show what effects too much information given to a person can do if they're never actually educated on how to correctly interpret it.

Makes you wonder if today's cars are more reliable because of improved electronics, or simply because morons who tinker and hack things up are simply locked out from under the hood to prevent them from tampering with things...

Dracula
10-12-2012, 11:01 PM
Just to clarify, this is for a theorized experimental gauge setup for a Bricklin, not a DeLorean. I want to redesign the hard-to-read gauges and put something that looks classy; not like an off-the-shelf solution like I have now. There's only one cooling fan and, now that I have a better understanding of what to do with the gauge, I might wire it in to the air compressor to see when that kicks in and how much it draws.