PDA

View Full Version : General Blower only has speed 3 and 4



marshdutt
01-05-2013, 04:45 PM
4542 has this issue that has been around as long as i have had her (only a couple months). The dail rotates around like normal, except nothing happens in 1 and 2. In the manuel it says that 3 and 4 have thier own relay (if im reading that right), but dont see anything about 1 and 2. Could it be that my blower motor had been switched out previously and now only has 2 speeds and wired to 3 and 4?

Anybody have this happen before? or how could i start to troubleshoot this? relays? switch? motor? wiring?

Rich
01-05-2013, 05:11 PM
Here's where you can find the schematic for the A/C system showing the circuit you want to troubleshoot:

http://dmctalk.org/showthread.php?40-All-Wiring-Schematics

From the symptoms it looks like you need to look at something upstream of the last resistor (3rd speed, which is OK) all the way back to and including the fan switch, including connectors. It's not the motor or a relay. The fan motor has a single hot feed to it.

Best guess is that it's the 2nd speed resistor, which is in the circuit for both speeds 1-2, or a connection just before/after that resistor. A single break there would kill speeds 1 and 2 only. Other causes are possible.

DMC5180
01-05-2013, 05:25 PM
Best guess is that it's the 2nd speed resistor, which is in the circuit for both speeds 1-2, or a connection just before/after that resistor. A single break there would kill speeds 1 and 2 only. Other causes are possible.

+1

Remove two hex head screws from the resistor assembly It's the multi-way plug to the left of the blower motor. Also look for signs of heat distress on the connect housing. They like to melt and it can be difficult to remove the connector if this happens. The good thing is you don't have to un-plug it to drop the resistor for inspection.

chenderson2k
01-05-2013, 05:34 PM
Don't speeds 1/2 and 3/4 run through separate circuit breakers?

Perhaps one of them is bad. This would be really easy to test simply by swapping them and seeing if speeds 1 and 2 suddenly start working.

If it is the circuit breaker, you can get a replacement at Oreilly's for about $3.

It may of course be the resistor pack on the blower motor as well. I don't have the info in front of me at the moment but I believe there is a cross reference for that part as well.

Rich
01-05-2013, 06:48 PM
Don't speeds 1/2 and 3/4 run through separate circuit breakers?


No, that's not the factory setup, but it's correct that 1/2 share a part of the blower fan circuit that neither 3 nor 4 share with them. See A/C schematic link in post #2.

3 and 4 each use their own CB. Speeds 1 and 2 have no CB.

Am not sure where the resistors are - a failure in or around the speed 2 resistor remains the most likely cause of the described symptoms.

DeLorean03
01-05-2013, 07:05 PM
The resistors are located in the passenger foot well near the bottom of the glove box compartment area.

Photo courtesy of SpecialTAuto:

15776

marshdutt
01-05-2013, 10:37 PM
thank you for your help, i should be heading home tomorrow, then probably working on the D on monday, i will post more info or picture in a couple days if i cannot find the culprit! thanks again

DMCMW Dave
01-06-2013, 09:20 PM
Loss of speed 1 and 2 is either a failed (broken, usually rusty) resistor or a bad fan speed switch (or bad wiring at either the switch or the resistor pack)