View Full Version : General What do these cars actually weigh?
Nicholas R
01-09-2013, 02:49 AM
Does anyone know what DeLoreans actually weigh? I'm curious about both automatics and manuals.
According to the manual, the car weighs 2743lbs with a full tank of gas, with a distribution of 63% rear, 37% rear.
http://2.bp.blogspot.com/-QkHFjVW_ohI/UO0Pae4BJdI/AAAAAAAABJI/vZBLB5_HWVc/s1600/IMG_0990.jpg
According to the VIN plate, the car weighs 3180lbs, (1244 front/1936 rear) with a distribution of 61% rear, 39% front.
http://4.bp.blogspot.com/-QgQjHAYZaws/UO0QhZGpoqI/AAAAAAAABJk/gL66JZKZ-MI/s1600/IMG_0988.jpg
Has anyone ever weighed one to find out what the correct answer is? I'm curious because tonight I weighed my car with the new engine and I want to know what to compare it to. My new weight (assuming full tank of gas) was 2,974lbs with a distribution of 63.7% rear, 36.3% front.
On the scales:
http://4.bp.blogspot.com/-2fFnhiw0abU/UO0PZaqzCYI/AAAAAAAABJA/-n0P3Z8gMvA/s1600/IMG_0986.jpg
Scale readings:
http://2.bp.blogspot.com/-6qdDHOjOEaU/UO0Pa32GhkI/AAAAAAAABJQ/VSIe1H_ewxg/s1600/Weight+Photo.JPG
Results:
http://1.bp.blogspot.com/-RJptyA3NBiU/UO0PU-ciC6I/AAAAAAAABI4/NzpOt8W-rzs/s1600/Data.JPG
jmettee
01-09-2013, 09:14 AM
I have info at home on my PC, can post it later. I weighed mine (stock, manual) at work with vehicle scales & came pretty close to what the dataplate says.
Mark D
01-09-2013, 10:21 AM
The 3180 number on the vin tag is the max rated weight the car is able to theoretically handle, also know as GVWR.
The front axle is rated at max 1244 lbs and the rear is rated for max 1936 lbs. With a curb weight listed at 2743 that means 437 lbs of weight can be added to the car without overloading it beyond the recommended limits.
The GVWR number doesn't really mean a hell of a lot though and is usually a (somewhat) made up number. It could be based off of durability testing and a factor of safety added in, or someone could have completely pulled a number out of their ass. Manufacturers can under rate a vehicle so it can fit into a certain vehicle weight class...or special ratings are allowed with certain restristrictions such as limiting speed at the overloaded weight.
It probably doesn't take much to overload a DeLorean beyond the GVWR...put a few people in the seats and a bag or two in the trunk and you are right there.
When the pilot cars were being run around the test track and sent for extended mileage testing the engineers most likely evaluated the suspension to determine a safe number that would allow for reasonable cargo capacity while providing some assurance that there would not be warrenty claims with people breaking suspension parts while still being loaded below the listed GVWR.
David T
01-09-2013, 10:21 PM
Back in June '12 I got my hands on a set of Longacre Racing scales for a few days. I weighed everything I could find. The results on my Delorean:
Stock, automatic transmission, unloaded, no driver, full fuel tank
LF 532 RF 521
LR 900 RR 915
Total 2868
Cross 1421 49.5%
Left 1432 49.9%
Rear 1815 63.2%
Gross 3244
Empty 2868
Useful Load 376 divided by 2= 188
All in pounds. From these numbers we can see some important things. The Delorean is very heavily biased in weight to the rear. Obvious because of the rear engine. Means once the back comes loose it is not going to stop easily. Especially with the limited turn radius of the front suspension
Next, the difference between empty and gross is VERY small. It leaves only 188 pounds for a driver and the same for a passenger AND NOTHING FOR LUGGAGE!
The car is almost perfectly balanced side to side (impressive). With the low (comparativly speaking) front loading we can see why they opted to go with manual steering. From this little exercise we can see that it is very important to limit anything that will add weight to the car. The next step would be to run the numbers regarding HP to weight. Again you will see the car is underpowered by today's standards. Another reason to keep the weight of the car down as much as possible. The automatic is slightly heavier than the 5-speed (maybe around 50 lbs).
David Teitelbaum
opethmike
01-09-2013, 10:35 PM
Oh Dave, I don't think Nick's car has any problems with power...
Jonathan
01-09-2013, 11:11 PM
...Gross 3244
Empty 2868
Useful Load 376 divided by 2= 188
All in pounds. From these numbers we can see some important things. The Delorean is very heavily biased in weight to the rear. Obvious because of the rear engine. Means once the back comes loose it is not going to stop easily. Especially with the limited turn radius of the front suspension
Next, the difference between empty and gross is VERY small. It leaves only 188 pounds for a driver and the same for a passenger AND NOTHING FOR LUGGAGE!
The car is almost perfectly balanced side to side (impressive). With the low (comparativly speaking) front loading we can see why they opted to go with manual steering. From this little exercise we can see that it is very important to limit anything that will add weight to the car. The next step would be to run the numbers regarding HP to weight. Again you will see the car is underpowered by today's standards. Another reason to keep the weight of the car down as much as possible. The automatic is slightly heavier than the 5-speed (maybe around 50 lbs).
David Teitelbaum
I wonder if one of our Time Machine conversion members would chime in here about how much extra weight all the movie props add to the car? I was under the impression it was 600-700 pounds. With knowing the limits of what the stock car can handle in terms of extra weight, do time machine cars get some sort of beefed up support system underneath on the suspension or frame in some way? If one were to add all the BTTF prop weight to the car, it sounds like it would be pushing it over the limit on operating well or safely.
Nicholas R
01-10-2013, 01:29 AM
Back in June '12 I got my hands on a set of Longacre Racing scales for a few days. I weighed everything I could find. The results on my Delorean:
Stock, automatic transmission, unloaded, no driver, full fuel tank
LF 532 RF 521
LR 900 RR 915
Total 2868
Cross 1421 49.5%
Left 1432 49.9%
Rear 1815 63.2%
Gross 3244
Empty 2868
Useful Load 376 divided by 2= 188
All in pounds. From these numbers we can see some important things. The Delorean is very heavily biased in weight to the rear. Obvious because of the rear engine. Means once the back comes loose it is not going to stop easily. Especially with the limited turn radius of the front suspension
Next, the difference between empty and gross is VERY small. It leaves only 188 pounds for a driver and the same for a passenger AND NOTHING FOR LUGGAGE!
The car is almost perfectly balanced side to side (impressive). With the low (comparativly speaking) front loading we can see why they opted to go with manual steering. From this little exercise we can see that it is very important to limit anything that will add weight to the car. The next step would be to run the numbers regarding HP to weight. Again you will see the car is underpowered by today's standards. Another reason to keep the weight of the car down as much as possible. The automatic is slightly heavier than the 5-speed (maybe around 50 lbs).
David Teitelbaum
Thanks for this info Dave! This is actually exactly what I was looking for. Since my car used to be an automatic, I'm glad to know where I would have been in the past. I'm curious if anyone has any hard data on manual's too, but it's nice to know that the swap only added 100lbs to the car and didn't change the distribution.
David T
01-10-2013, 09:10 PM
As you can see 100 lbs is not the same 100 lbs in the front as it would be in the back. Adding more weight in the back is going to have a bigger effect quicker than in the front because of the already heavy bias in the back. Not so important during acceleration or steady-state, the problems will be multiplied during braking and/or cornering. You might want to consider adding an adjustable proportioning valve to reduce the braking power on the rear. That will have the bad effect of increasing braking distances. You might also have to experiment with higher tire pressures on the rear. That has as it's bad effect a smaller footprint and an increased tendency to lose traction. Lowering the rear height may help but then you need adjustable lower links to adjust the camber. With that extra 100 lbs you can now only add 276 lbs for driver AND passenger before you blow the gross! One has to consider ALL of the effects of ANY modification and how they will overcome the worst of them. It is all a compromise. One part of your solution may be to move the battery to the front. Running over gross is bad because it overloads parts and causes them to wear and fatigue quicker, increases braking distances, hurts fuel economy, and can make the car uncontrollable under certain conditions. IMHO you have a considerable "cushion" or margin of safety on the gross before you see a lot of bad things happen so if you are, say, 10% over gross or 3568, you will still be safe. Just be aware of what you are doing and know what to expect as you overgross the car. If you swapped a bigger motor into the car the frame was designed for a certain level of loading. Overloading the frame can lead to cracking and twisting so you may need to reenforce areas of the frame. That can also add to your weight problem. Keep an eye on the frame at least. Seems there is a large safety margin there too.
David Teitelbaum
vwdmc16
01-11-2013, 12:14 AM
I weighed my car about 6 months back on longacre scales too, It was empty but a full tank. A bit disappointing.
2832lbs 36.8%F 63.2%R
Nicholas R
01-11-2013, 12:27 AM
As you can see 100 lbs is not the same 100 lbs in the front as it would be in the back. Adding more weight in the back is going to have a bigger effect quicker than in the front because of the already heavy bias in the back. Not so important during acceleration or steady-state, the problems will be multiplied during braking and/or cornering. You might want to consider adding an adjustable proportioning valve to reduce the braking power on the rear. That will have the bad effect of increasing braking distances. You might also have to experiment with higher tire pressures on the rear. That has as it's bad effect a smaller footprint and an increased tendency to lose traction. Lowering the rear height may help but then you need adjustable lower links to adjust the camber. With that extra 100 lbs you can now only add 276 lbs for driver AND passenger before you blow the gross! One has to consider ALL of the effects of ANY modification and how they will overcome the worst of them. It is all a compromise. One part of your solution may be to move the battery to the front. Running over gross is bad because it overloads parts and causes them to wear and fatigue quicker, increases braking distances, hurts fuel economy, and can make the car uncontrollable under certain conditions. IMHO you have a considerable "cushion" or margin of safety on the gross before you see a lot of bad things happen so if you are, say, 10% over gross or 3568, you will still be safe. Just be aware of what you are doing and know what to expect as you overgross the car. If you swapped a bigger motor into the car the frame was designed for a certain level of loading. Overloading the frame can lead to cracking and twisting so you may need to reenforce areas of the frame. That can also add to your weight problem. Keep an eye on the frame at least. Seems there is a large safety margin there too.
David Teitelbaum
I agree with you about the braking. To help that out I installed custom 4 piston drilled and ventilated Wilwood brakes on the front. It makes a pretty significant difference. Haven't looked into an adjustable proportioning valve yet though. I've also got the Eibach lowered kit so I've adjusted the rear ride height accordingly. You are correct though that the rear camber was affected by the extra weight and I have a set of Marty Maier's adjustable rear lower links. I haven't installed them yet but am hoping to do in the next few weeks. The front the car also has the shock tower strut bar and the lower control arm brackets so they certainly help hold the front end together during acceleration.
Honestly the next big upgrade that I am considering (actually I'm beyond considering, I've decided that it's a necessity) is the limited slip differential. Even with all that weight over the rear wheels, that open differential just does not cut it.
I weighed my car about 6 months back on longacre scales too, It was empty but a full tank. A bit disappointing.
2832lbs 36.8%F 63.2%R
Thanks for the numbers!! Is your car a manual or an automatic? Because of the 30lbs less than Dave's I assume a manual?
EDIT: Just looked at your restoration thread and saw that it is indeed a manual :D
Dangermouse
01-11-2013, 10:02 AM
Interesting thread.
Presumably there was a standard weight of an average person in 1981 that they used in their design and it would have been less than 188lb. Possibly 150 or 160 to allow for some luggage. I wonder what number the car companies use today for the average American?
Would be great to get a BTTF car on these scales too
David T
01-11-2013, 11:04 AM
Drilled and ventilated rotors won't help with braking distances, they will just delay the onset of fade. You might consider a more aggressive pad but it will chew up the rotors. The limited slip diff (a quafe) will only help during certain particular driving conditions. About the only time you will encounter such conditions is on a track while racing. IMHO way too expensive for the very limited gain. In fact, with the Quafe, under other different conditions, it can actually make it harder to control. We see this in the Lotus, it has an open diff and some have put the Quafe in and after spending all of that money they do not have a whole lot of good things to say about it. Few will say it was a bad thing, especially after plunking down all of that money! What does make sense is the one piece input shaft. You should also be using Redline MT-90 in the transaxle now. The money spent on the Quafe would be better spent on an advanced driving course like a Skippy course. Learn how to drive better and you don't need the Quafe. It seems you have already made up your mind. Let us know how it works out.
David Teitelbaum
jmettee
01-18-2013, 11:25 PM
Forgot about replying with my info for a few days. Here's what I weighed on my stock manual with all the "extras" taken out (tools, fire extinguisher, etc) & full of fuel.
Front 1054 (37.5%)
Rear 1757 (62.5%)
Total 2811
Nicholas R
01-19-2013, 12:22 AM
Drilled and ventilated rotors won't help with braking distances, they will just delay the onset of fade. You might consider a more aggressive pad but it will chew up the rotors. The limited slip diff (a quafe) will only help during certain particular driving conditions. About the only time you will encounter such conditions is on a track while racing. IMHO way too expensive for the very limited gain. In fact, with the Quafe, under other different conditions, it can actually make it harder to control. We see this in the Lotus, it has an open diff and some have put the Quafe in and after spending all of that money they do not have a whole lot of good things to say about it. Few will say it was a bad thing, especially after plunking down all of that money! What does make sense is the one piece input shaft. You should also be using Redline MT-90 in the transaxle now. The money spent on the Quafe would be better spent on an advanced driving course like a Skippy course. Learn how to drive better and you don't need the Quafe. It seems you have already made up your mind. Let us know how it works out.
David Teitelbaum
The ventilation in the brakes doesn't help the braking, it's the fact that they're 4 piston calipers that helps them. They also have very aggressive wilwood pads to dig into the wilwood discs. The braking is VERY noticeably improved.
Also I very much disagree about the LSD. The LS1 produces a lot of power, much more than you're used to in a Delorean, and if either tire has a reduction in traction, there is no hesitation before that tire spins freely. It's not a question of my driving ability, it's just physics. In an open differential the power follows the path of least resistance; only takes one wheel. Cliffs car with the 2JZ supra engine has the LSD and it is a truly noticeable difference. Eddy was telling me about when he first did that swap and how he did a 360 in the car after accelerating through a puddle down in FL. After that he knew he needed the LSD. I haven't done any 360s but if definitely felt the traction loss many times. To me the LSD is a very justifiable improvement.
thirdmanj
01-19-2013, 12:27 PM
All this talk of LSD is very exciting!
David T
01-20-2013, 01:58 PM
One big reason in the Lotus's for getting a LSD is if one wheel should lose traction momentarily and then quickly regain it you can get enormous shock loads into the drivertrain. The LSD is supposed to help reduce that. There are things you can do with the suspension that can mitigate the bad effects and I would try some of them first. Getting a LSD only trades some bad traits for others. You will find that out once you get it. The # of pistons all by itself does not change the way the brakes work. It has to do with pressures and that is a function of the sizes of the pistons. 4 small pistons can do what 2 larger ones can do if they are sized accordingly. The composition of the brake pads can have a HUGE effect on braking characteristics. Ventilating and drilling the rotors not so much. Typically the more aggressive the pad the more they will chew up the rotors. Also the most aggressive pads only really get good once they get hot. Till then they really don't 'bite". Not a good trait for a car driven on the street where you may have to do a panic stop on cold brakes.
David Teitelbaum
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.