Log in

View Full Version : Brake Brake Indicator Light Doesn't Work, Not The Bulb, How to test Parking Brake Switch?



DeloreanJoshQ
01-20-2013, 07:13 PM
Has anyone run to the issue of the brake indicator light not working in the dash?
I thought it was the bulb so I removed the binnacle and replaced it and the light still doesn't come on when the parking brake is engaged.
How do you test the parking brake switch?
If the low brake fluid light switch doesn't work, does the light not come on for either it or the parking brake switch?
I like having the reminder that my parking brake is engaged :)

Thanks!

Josh Q

DMC5180
01-20-2013, 07:23 PM
There are 2 switches independent of each other. The P-brake switch and the Reservoir level switch. If nothing happens with the P-brake. Take the cap off the Brake fluid reservoir. the float switch should make contact and light come on (key ON). If the light still does not come on. Then the issue is likely on the 12V feed side of the bulb.

AirmanPika
01-20-2013, 10:54 PM
Well you could always just pull the connectors to the switch and short the leads to see if flips the light on and off. If it does...then you know it is the switch.

My switch was always giving me issues. Turned out there was heavy corrosion on it. I tore it apart, cleaned it, slapped it back together and now it works beautifully.

Jonathan
01-20-2013, 11:14 PM
My switch was always giving me issues. Turned out there was heavy corrosion on it. I tore it apart, cleaned it, slapped it back together and now it works beautifully.

+1 This is exactly how my brake warning light issues were resolved too. The switch is not hard to access. Pull the rubber sleeve off the p-brake handle, lift out that custom shaped piece of carpet covering the base of the p-brake handle, and you should be able to see what it is that's going on with the switch. Don't underestimate how poor the connections may be as shorting the switch together didn't always make my bulb go on. Not sure what else might have been at play there, but taking it all apart, cleaning it up, and reinstalling everything snug made it all work.

That being said, I'm not sure I've ever seen my brake fluid reservoir switch actually turn the light on. During regular driving nor doing it as a test. I think on my car the little contraption on top of the reservoir is shot. I recall the top of it looks like the bubble burst, if you know what I mean. I don't think the guts of it work anymore.

I'll agree with you on how important it is to have that p-brake light working. On no less than two different occasions I have driven relatively long distances before realizing the p-brake was still engaged. It always coincides with taking someone for a ride for the first time too. Must be something about getting distracted easily. Look... squirrel....

WelmoedJ
01-21-2013, 05:06 AM
+1 This is exactly how my brake warning light issues were resolved too. The switch is not hard to access. Pull the rubber sleeve off the p-brake handle, lift out that custom shaped piece of carpet covering the base of the p-brake handle, and you should be able to see what it is that's going on with the switch. Don't underestimate how poor the connections may be as shorting the switch together didn't always make my bulb go on. Not sure what else might have been at play there, but taking it all apart, cleaning it up, and reinstalling everything snug made it all work.

That being said, I'm not sure I've ever seen my brake fluid reservoir switch actually turn the light on. During regular driving nor doing it as a test. I think on my car the little contraption on top of the reservoir is shot. I recall the top of it looks like the bubble burst, if you know what I mean. I don't think the guts of it work anymore.

I'll agree with you on how important it is to have that p-brake light working. On no less than two different occasions I have driven relatively long distances before realizing the p-brake was still engaged. It always coincides with taking someone for a ride for the first time too. Must be something about getting distracted easily. Look... squirrel....

The P (Emergency ???) brake handle and the brake reservoir switch share - as said - the brake light.
The brake reservoir switch is placed in a forward position making it easy to get dirty over time.
Take the rubber connector off of the switch and take a good look at the connector pins, you would be shocked by the accumulated dirt and corrosion.
Clean the pins and use a lot of brake cleaner on the contacts in the switch socket (not while it's on the reservoir, please).
Use sandpaper to finish cleaning and use come contact spray to pevent and delay rust.

Problem with the placement of the connector is the wiring: too short to turn the switch 180 degrees (to the rear).
I used - after the cleaning procedures) some electronics sealant to cover the wire side of the connector and the connection of plug and socket to keep it from attracting dirt and most.
I no longer have problems with the brake light.

DMCMW Dave
01-21-2013, 09:08 AM
The switch that is operated by the parking brake handle is not weathertight and gets wet the first time (and every time) you open the door in the rain.

General note:
This is one thing to remember when troubleshooting lights that don't work on this car- - check the bulb LAST. The bulb us usually the hardest part to get to, and the problem is more caused by a bad connection somewhere else, or on the bulb socket itself.

DeloreanJoshQ
01-26-2013, 10:28 PM
The switch that is operated by the parking brake handle is not weathertight and gets wet the first time (and every time) you open the door in the rain.

General note:
This is one thing to remember when troubleshooting lights that don't work on this car- - check the bulb LAST. The bulb us usually the hardest part to get to, and the problem is more caused by a bad connection somewhere else, or on the bulb socket itself.

I have the binnacle removed so I can send it to Dave to be recovered and add a 140 speedo.
I cleaned the ground connection on the parking brake bracket. Where exactly does the ground wire go so I can check to make sure I have a good ground to the switch?
I removed and cleaned the switch connection. The switch appears to click and function great. Where exactly does the wire go between the switch and the brake indicator light so I can check for continuity?

WelmoedJ
01-27-2013, 06:57 AM
I have the binnacle removed so I can send it to Dave to be recovered and add a 140 speedo.
I cleaned the ground connection on the parking brake bracket. Where exactly does the ground wire go so I can check to make sure I have a good ground to the switch?
I removed and cleaned the switch connection. The switch appears to click and function great. Where exactly does the wire go between the switch and the brake indicator light so I can check for continuity?

The brake light switch runs to ground near the switch.
The other wire goes to the brake light in the instruments panel.

It seems you do not have the electrical diagram for our cars.
May I advise to get the colour diagram from this site?
Very helpful to find connections and understand the how parts are fed and grounded.

DeloreanJoshQ
01-27-2013, 10:24 AM
The brake light switch runs to ground near the switch.
The other wire goes to the brake light in the instruments panel.

It seems you do not have the electrical diagram for our cars.
May I advise to get the colour diagram from this site?
Very helpful to find connections and understand the how parts are fed and grounded.

I do have a very nice detailed diagram, but it does not tell me the physical route the the wires take. It says ground for switch. Ok, so on a fiberglass body, where is that ground? It says the signal goes fron the switch to the light. Ok, without pulling the interior back apart where does the wire route? Under your feet to the binnacle or back to the bulkhead and then up the console?

WelmoedJ
01-27-2013, 10:57 AM
I do have a very nice detailed diagram, but it does not tell me the physical route the the wires take. It says ground for switch. Ok, so on a fiberglass body, where is that ground? It says the signal goes fron the switch to the light. Ok, without pulling the interior back apart where does the wire route? Under your feet to the binnacle or back to the bulkhead and then up the console?

From the switch the wire runs on the floor rearwards then up to the center console where it's integrated in the driver's side wire loom to the front of the car.
In the footwell it's split from the main wireloom into one of the looms going to the instruments panel.
It's part of the (seen from the driver's seat) right hand side loom that ends in the connector to the circuit sheet of that panel.

There is a connector layout in the diagrams section of this forum which shows you the exact pin used for the brake light.
Mind that this brake light also is grounded through the switch on the main brake cylinder reservoir.
Either switch grounded makes the light turn on.

Hope this helps.

DeloreanJoshQ
03-19-2013, 10:14 AM
Running out of testing ideas...

Progress thus far:

-Brake Reservoir Switch
-Found the ground is good (connected the ground pin at the harness connector to the brake master cylinder and tester beeped)
-I forgot to test the switch by connecting tester to each pin on the switch and testing for continuity when float goes down, ugh.
-Cleaned all of the connections on the harness connector and reservoir cap connector with electrical cleaner and small brush
-Light still would not come on with the cap off or by messing with the brake fluid float

-Parking brake Switch
-Found the ground is good (connected the ground wire connection(ring terminal under bolt or housing) to negative side of battery and tester beeped)
-Switch tested good (touched switch connector to ground(parking brake housing) with tester and it beeped when I engaged the parking brake)
-Tested gauge cluster wiring harness plug connector and no continuity (no beep from tester when touching brake indicator connection to parking
brake switch connector) This tells me there is a break between the plug that goes into the instrument cluster and the parking brake switch...
-Traced signal wire from parking brake switch up to where it enters center console wire bundle and passed continuity test.


-Brake Indicator Lamp
-When I turn the key on the brake indicator lamp "blips" -Tells me the bulb is good and that it does get brief power when key turns on or off
-"New" NOS print circuit ribbon installed. All other gauges and lamps have been replaced with NOS, tested, and work.

At this point the only thing I can think of doing is:
-attempting to find where both the brake reservoir signal wire and parking brake signal wire meet and testing for continuity at the connector to the parking brake switch. (Any ideas?)
-OR rewire the whole circuit and jettison the original wiring...don't want to do this because it will create more wiring mess.

Any other thoughts?
Thanks for all of the help!

Ron
03-19-2013, 11:22 AM
Fwiw, it shouldn't blip when you turn the key on/off...do the Oil and/or Battery lights do this too?

Sounds like you may have a poor connection where the three BW wires are joined together or, as said, a bad connection/break in the BW wire on the way to the cluster.
Do you have continuity from the BW at the reservoir connection to the BW at the P-brake connection?
If you run a jumper from the battery (-) to the BW wire side of the bulb, does it come on and stay on?

DeloreanJoshQ
03-20-2013, 08:32 PM
Fwiw, it shouldn't blip when you turn the key on/off...do the Oil and/or Battery lights do this too?

Sounds like you may have a poor connection where the three BW wires are joined together or, as said, a bad connection/break in the BW wire on the way to the cluster.
Do you have continuity from the BW at the reservoir connection to the BW at the P-brake connection?
If you run a jumper from the battery (-) to the BW wire side of the bulb, does it come on and stay on?

-I have the biggest and brightest LED bulbs installed, would that make a difference(LEDs more sensitive and faster to slight power surges)?
-The oil and battery lights do not do this because they stay on until the engine starts.
-I didn't check continuity from the BW wire at the reservoir to the P-brake connection. The wiring diagram shows a diode on the leg that goes to the reservoir so that it doesn't back feed. Would this affect the testing?
-If I run a jumper from the neg post to the BW side of the bulb in the cluster and the bulb does/doesn't come on, what clues would that provide?

Thanks for the help!

Ron
03-20-2013, 08:51 PM
-I have the biggest and brightest LED bulbs installed, would that make a difference(LEDs more sensitive and faster to slight power surges)?
-The oil and battery lights do not do this because they stay on until the engine starts.
-I didn't check continuity from the BW wire at the reservoir to the P-brake connection. The wiring diagram shows a diode on the leg that goes to the reservoir so that it doesn't back feed. Would this affect the testing?
-If I run a jumper from the neg post to the BW side of the bulb in the cluster and the bulb does/doesn't come on, what clues would that provide?

Thanks for the help!
OK..good info!

First, that is not a diode, it is a connection/plug, but forget that for now.

Since the oil and battery lights stay on, the circuit that feeds the cluster for the brake light is working to those points (all of the lights on that side share it, except the lambda light). And since grounding the other side of the bulb via the BW wire does not make it light, it is a VERY strong indication that the printed circuit, bulb holder, or bulb is bad. Check for 12V on the other side of the bulb, I bet it is dead...or the bulb holder/connection is poor (being why it flashes). Note 12V on a meter DOES NOT mean it can make a bulb burn (it does not allow for amperage draw ie it can be 12V but too weak)...this is why I use an "ice pick" tester....

DeloreanJoshQ
03-20-2013, 09:10 PM
The item on the left side of the image that looks like a vertical cylinder, that is a plug?

http://i125.photobucket.com/albums/p48/jaq78/Deloreanbrakewiring.png

I'll have to perform the other tests and report back...

Ron
03-20-2013, 09:12 PM
Yes.

Diodes look like a bold arrow pointing to a bar:
----->|----

DeloreanJoshQ
03-20-2013, 09:13 PM
Yes.

Diodes look like a bold arrow pointing to a bar:
----->|----

So if I find that plug then I have another place to test. Any ideas where it is?

Ron
03-20-2013, 09:20 PM
So if I find that plug then I have another place to test. Any ideas where it is?
No. You can never tell the physical location from the schematic and I can't remember seeing it. But I can tell you it is only for the reservoir light (forget it for now).

I'd bet money the problem is within an inch of the bulb.

DeloreanJoshQ
04-07-2014, 09:35 PM
Finally got back to this since the front fascia is off and new one being painted. Ron was the closest to the answer.
The problem is the connections t the back to the printed circuit ribbon. As I move them around, stuff either works or stops working,including the brake light.so now I need to figure out how to connect it where everything works but still can lower the binnacle back in place without disturbing the wiring...

Patrick C
04-07-2014, 09:44 PM
Finally got back to this since the front fascia is off and new one being painted. Ron was the closest to the answer.
The problem is the connections t the back to the printed circuit ribbon. As I move them around, stuff either works or stops working,including the brake light.so now I need to figure out how to connect it where everything works but still can lower the binnacle back in place without disturbing the wiring...

I used a few dabs of superglue to keep the printed copper tabs from popping up.

SpudMurphy
12-04-2025, 07:43 AM
Parking brake light will not come on.
I shorted tge two wires to the handbrake.. no joy!
As mentioned in this thread,the bulb flickers when the ignition is turned on.
I have a new pcb fitted to the binnacle.

https://youtube.com/shorts/LgPNte8eZ1w?si=k_1wvajxPzE7SU3U

DMC5180
12-04-2025, 08:37 AM
Parking brake light will not come on.
I shorted tge two wires to the handbrake.. no joy!
As mentioned in this thread,the bulb flickers when the ignition is turned on.
I have a new pcb fitted to the binnacle.

https://youtube.com/shorts/LgPNte8eZ1w?si=k_1wvajxPzE7SU3U

It sounds like you?re just turning the ignition switch in the video. Were you also lifting the P-Brake handle?

The circuit itself has two switches, the brake fluid low level switch ( check your fluid level, it could be on the raged edge trying to turn the light on ) Also this should make the light come on if the Cap is lifted out of the reservoir.


Sent from my iPhone using Tapatalk

SpudMurphy
12-04-2025, 09:08 AM
It sounds like you?re just turning the ignition switch in the video. Were you also lifting the P-Brake handle?

The circuit itself has two switches, the brake fluid low level switch ( check your fluid level, it could be on the raged edge trying to turn the light on ) Also this should make the light come on if the Cap is lifted out of the reservoir.


Sent from my iPhone using Tapatalk

Thanks for you?r reply.
The parking brake was on in the demo.
As I recently installed a new PCB on the binnacle , and it is not secured onto the dash, Im about to take it off and investigate further.

At least Binnacle pcb replacement cured one problem .. the main beam blue light warning bulb.
Alas, the other problem was the incandescent battery / ignitionwarning light necessitated a replacement 140 amp alternator :-(

Ill report back when the solution has been found.

SpudMurphy
12-04-2025, 09:33 AM
Thanks for you?r reply.
The parking brake was on in the demo.
As I recently installed a new PCB on the binnacle , and it is not secured onto the dash, Im about to take it off and investigate further.

At least Binnacle pcb replacement cured one problem .. the main beam blue light warning bulb.
Alas, the other problem was the incandescent battery / ignitionwarning light necessitated a replacement 140 amp alternator :-(

Ill report back when the solution has been found.

Sorted. That was an easy fix! Im happy to share my error in the hope that it will help other owners in the future.
Despite me labelling the led bulbs showing the ground on each one, I simply removed the led and reversed it.
It all works fine. . Both the low fluid level and the handbrake on warning.
I can now get the binnacle reinstated and relax!
Thanks again71908

DMC5180
12-04-2025, 10:25 AM
[emoji106]


Sent from my iPhone using Tapatalk

Timeless
12-04-2025, 11:14 AM
Tip for anyone going into the cluster to install LED bulbs. I plugged the cluster in before reinstalling into the binnacle to make sure all the bulbs worked. Then put it in the binnacle and install in the dash.

SpudMurphy
12-05-2025, 04:19 AM
Tip for anyone going into the cluster to install LED bulbs. I plugged the cluster in before reinstalling into the binnacle to make sure all the bulbs worked. Then put it in the binnacle and install in the dash.

Yup exactly. Also change to M4 wingnuts.

Timeless
12-05-2025, 02:52 PM
Yup exactly. Also change to M4 wingnuts.
Yes! Forgot to mention that