PDA

View Full Version : General I'm trying to save a little cash



krs09
01-22-2013, 01:56 AM
I have been in the middle of taking care of the VOD for a while now and thing are going back together. I'm replacing as many parts that I can but trying to save a little cash in doing it. My question is the sensors in the Y pipe and thermo housing. Shoud they be replaced if there is no problem at tear down? Should they just be takin out and cleaned? Any sensor known to fail more than others? I know they sould be replaced but is it worth it. I do have a fear of replacing everything, firing it up and nows thers a problem. I had the car checked out before tear down and was told to replace the thermo time but that was it. Now as I stare at sensors that have a good chance of being original or replaced in 93' (second owner from a "collection of cars") I have a feeling I should, but the car needs help in so many places. Thoughts ?


Fuzzy Dash #4870

sdg3205
01-22-2013, 04:12 AM
If they work I say no. Of course it's great to do everything while in there but now that you know how to do the vod it's not really a problem should you need to go back in down the road.

Not sure what those sensors cost but its your call. I can tear down an intake pretty quickly now having done mine twice and a few other cars. If you want to avoid it again soon then replace but if they work fine and your okay going back in every few years as preventative cleans are needed just skip them.

My 2 cents!

Chris 16409
01-22-2013, 04:26 AM
When I did service in my valley, I just replaced the ported vacuum switch (https://store.delorean.com/p-6267-switch-therm-vac.aspx). I was told the others have a very low fail rate and it is not worth it to replace them.

Bitsyncmaster
01-22-2013, 07:24 AM
I did not replace any sensors when I did my VOD. Just pull them out and clean them up. I did put new wire connectors, new bolts and new hoses on.

jmettee
01-22-2013, 07:58 AM
When I did service in my valley, I just replaced the ported vacuum switch (https://store.delorean.com/p-6267-switch-therm-vac.aspx). I was told the others have a very low fail rate and it is not worth it to replace them.

Same here. I tested all the sensors (values are in the shop book). All worked fine, even the vacuum switch, but I still replaced just that one because it seemed to me to be one that would most likely stop working before the other 2. IIRC, the others are thermal on/off switches or variable resistance.

David T
01-22-2013, 11:31 PM
I too agree that there is a very low failure rate on those sensors. I would test them and make sure they are working. You should also check the rubber vacuum hoses and if they are hard or split or cracked they should be replaced. Make VERY sure you route them correctly, it is hard to get back in there to fix it if you mess up. Pressure test your cooling system BEFORE you reinstall your intake manifold.
David Teitelbaum

TTait
01-23-2013, 12:24 AM
Pressure test your cooling system BEFORE you reinstall your intake manifold.
David Teitelbaum

+10

You can borrow one at auto zone or your local parts chain store...

As to your original question - I also think the ported switch would be the one to change if any, it has moving parts.

Tom

krs09
01-23-2013, 09:57 AM
Thanks guys for all your info.. I will pressure test before I put everything back together for sure. I have replaced the water pump all coolant hoses - hot water valve - cooling fans from dpnw - all vacuum hoses - new belts - all hardware and seals - otterstat - idle micro switch (po modified bracket now i have to get a new one of those too, ugh) and i will replace the vacuum sensor in the y pipe. I dont want to cut corners but just want to get my priorities straight. All your tips are gold. Thank you. Any other parts that should be replaced during a mini restoration and any that can be left alone. Any myths of high fail rate parts that can be left alone?

Delorean Industries
01-23-2013, 10:15 AM
The spade connector sensor usually has a low failure rate. I have seen quite a few idle thermistors bite it lately causing weird conditions during warm up and idle. I would replace that one. (this is the sensor with the bosch style two wire plug) and of course the vacuum valve is a must.