View Full Version : Engine Leaking Coolant from Right Head Gasket
David T
01-23-2013, 11:18 AM
My car has been slowly leaking small amounts of coolant from the right head just above the starter, about the middle. I pulled the head and it was warped about .004. The gasket was in good condition but not tightly clamped in the center allowing the leak. #2 intake was not seating well and the compression was only about 70 psi. According to the Workshop Manual the flatness spec for the head is .002 and the head is not serviceable. I had .005 taken off. Aftermarket manuals that the machinist provided allow .025. The intake valve seat was warped because the head was warped. Looks like the head was overheated but I never overheated and I have owned the car for over 15 years. I initially thought the gasket failed but it appears the head warped causing the failure. Has anyone seen any failures like this?
David Teitelbaum
OverlandMan
01-23-2013, 11:55 AM
My car has been slowly leaking small amounts of coolant from the right head just above the starter, about the middle. I pulled the head and it was warped about .004. The gasket was in good condition but not tightly clamped in the center allowing the leak. #2 intake was not seating well and the compression was only about 70 psi. According to the Workshop Manual the flatness spec for the head is .002 and the head is not serviceable. I had .005 taken off. Aftermarket manuals that the machinist provided allow .025. The intake valve seat was warped because the head was warped. Looks like the head was overheated but I never overheated and I have owned the car for over 15 years. I initially thought the gasket failed but it appears the head warped causing the failure. Has anyone seen any failures like this?
David Teitelbaum
My guess would be prolonged overheating could have caused this issue too. I wasn't aware that the head wasn't serviceable. Would that be because it's aluminum? Does the car burn off leaking coolant getting into the cylinder(s) (white smoke from exhaust)? Hopefully another member who's replaced a head or similar can chime in.
jmettee
01-23-2013, 12:00 PM
David,
If you recall, my car had the coolant smelling like the oil/combustion gasses, but the coolant was not oily. When I pulled the heads, I could not identify any locations of leakage between the cylinders & the coolant passages - but obviously combustion gasses (top cylinder) were entering the cooling system. I don't recall how much warpage I had, but I think the shop took off .005" (I'd have to check paperwork). All signs proved to me that I was the first to have the heads off this engine since it was new.
I am seeing more & more posts about "where is my coolant going?" & "my coolant tank is hissing". These were my symptoms....I was collecting air in the top of the radiator & if I didn't vent it off every 4-5 drives, the expansion of that air would push coolant out the overflow while driving. I never overheated the engine, but if the telltale sign of the oil-cap white plastic thing missing is a real indicator, then my engine did get hot at least once in its lifetime. However, based on this, I am assuming that 30 years of use (whether sitting or run normally), these head gaskets are starting to fail more & more often. Obviously overheating & warpage cause more issues on top of the age. It could be that your gasket just has deteriorated & coolant has found a path to the exterior of the engine.
David T
01-23-2013, 12:14 PM
The only sealing problem appears to have been the outer edge at the bottom center of the head under liner #2. The coolant was escaping externally. No combustion leaks. Right now it looks like an overheat problem possibly due to a plugged injector leaning out the #2 cylinder excessively. I have to test the injectors to confirm that theory. I just spoke to Josh at DPI and he thinks somehow that cylinder ran too lean and therefore too hot, warping the head and intake valve seat. Although the manual says non-serviceable the heads have been successfully resurfaced up to as much as .040 but at that much you must adjust the camshaft timing to compensate.
David Teitelbaum
Jason
01-23-2013, 12:22 PM
David,
If you recall, my car had the coolant smelling like the oil/combustion gasses, but the coolant was not oily. When I pulled the heads, I could not identify any locations of leakage between the cylinders & the coolant passages - but obviously combustion gasses (top cylinder) were entering the cooling system. I don't recall how much warpage I had, but I think the shop took off .005" (I'd have to check paperwork). All signs proved to me that I was the first to have the heads off this engine since it was new.
The same thing happened to me. I replaced the heads with DPI SPEC II heads so I never bothered to have to old ones checked, but I couldn't find any obvious leaks. Josh at DPI now has the old heads.
Delorean Industries
01-23-2013, 12:30 PM
The same thing happened to me. I replaced the heads with DPI SPEC II heads so I never bothered to have to old ones checked, but I couldn't find any obvious leaks. Josh at DPI now has the old heads.
Great to finally talk to you on the phone David!
Jason- we had to take a good amount off to fix your core heads. We were able to save the pair.
David T
01-23-2013, 09:20 PM
I was toying with the idea, while I had the motor apart, to go with hotter cams. After thinking it over I decided unless I was also going to change the exhaust system it didn't make sense. Sorry Josh, I won't be spending on your cams! I do thank you for your valuable advice on my problem. I try not to call and spend vendor's time on the phone, I know how valuable your time is. I guess I will have to buy something from you soon!
David Teitelbaum
Grover
01-23-2013, 09:51 PM
Justin,
You should chime in for Dave, as you have hot cams with the stock cross over pipe on the exhaust system.
jmettee
01-24-2013, 08:22 AM
Chime!
David, if you recall, I did put in hot cams "while I was in there" for the head gaskets. I ended up with Steger's just because his had been in cars going on 10 years at that time (I spoke to Josh AFTER I had already ordered & he has some different options). For now, I have stock manifolds & cross over, but have Hervey's modern CAT & a Flowmaster muffler. It woke the car up quite a bit. Josh Q in Ohio did pretty much the same as me, except maintained the stock CAT & muffler & could tell NO difference, so he then put on a header/exhaust system to realize the increases.
I also drove Steve's car, & there is a big difference between my setup & Steve's past 3500 RPM or so. Down low, they are fairly close from what the butt can tell. Bottom line, do cam while you're in there IF you at least anticipate changing out the muffler. The stock muffler is the biggest restriction in the exhaust system (if my dyno was anywhere close to being right, it proved this). Manifold/crossover pipe are the secondary restriction.
David T
01-24-2013, 09:56 AM
I agree with all of that but as you say, it won't make a lot of difference unless you modify the exhaust system and I have no plans for doing that. Another factor is that my car is an automatic and you would probably not notice as much improvement in an automatic.
David Teitelbaum
David T
01-25-2013, 10:50 AM
Got the head back from the machine shop. They had to take off .013 to get it flat. The #2 intake valve seat was egg-shaped, that's why the intake valve wasn't sealing (the head was warped right in the center). All of the springs were fine. Lapped in the valves and reassembled the head and installed it. Once I do a compression test I will decide if I have to do the other head. I still have to check the injectors to see if the #2 was making the cylinder run lean. I tightened the head up using Josh's method. I will redo it with the angular method and see what difference there is.
David Teitelbaum
David T
01-29-2013, 11:20 PM
The theory of a bad injector causing #2 to run lean didn't work. All of the injectors were dirty but all cleaned up and were flowing. It could be a bad mixture unit but all of the spark plugs looked about the same color. It would be nice if I could find a definitive cause for this so I know it won't happen again. I will test the mixture unit for equal flows. I will be getting the left head back Thursday and put it back on. Should have it running by the weekend.
David Teitelbaum
David T
01-31-2013, 10:45 PM
Well, it is not a bad injector. The left head was warped as well but nowhere near as bad. The only possibility is that the engine had to have been overheated at some point in it's past. The plastic screen in the oil filler is not melted so it couldn't have been badly overheated but it was enough to warp the heads. And it took all of this time to make itself apparent by a leaky head.
David Teitelbaum
...sometimes ya just get lucky ;-)
David T
02-01-2013, 01:41 PM
By "lucky" you must mean it is only going to cost me around $800? Between the gaskets and seals, machine work, and a water pump, that's what I will have in this repair. Never mind the labor! There goes my $500 a year budget!
David Teitelbaum
DMC5180
02-03-2013, 02:26 PM
David ,
When was the last time you actually had to spend money to repair or replace a failed or broken component? I'm not talking about preventative,cosmetic or routine maintenance.
David T
02-03-2013, 03:53 PM
For 2012:
Hood release cable (I had the back-up safety cable)
New batteries in the LockZilla remotes
Cleaned and adjusted passenger seat belt retractor (no cost item)
Cleaned fuel gauge sender wires (no cost item)
Greased front end, pressure tested cooling system and anti-freeze (no cost item)
Flushed brake system
For 2011
New voltage regulator
For 2010
Oil change and filter
As you can see if you have an ongoing Preventive Maintenance program (PM) , you do not have large expenses all the time. A top job or tires can blow your budget for the year. Once you have a well maintained car and keep at it, if you average your costs over years, you CAN manage to keep the car in good shape for under $500 a year, especially if you do your own work. One BIG benefit of keeping the car in good condition is that it is reliable besides being inexpensive to operate.
Anyone who thinks all you have to do is pay insurance, registration, and gas and drive on ANY car is in for a rude surprise!
David Teitelbaum
DMC5180
02-03-2013, 04:19 PM
Using that 3 year average you way under budget. What Alternator are you running that needed a voltage regulator? I'm guessing swapping the regulator as considerably Cheaper than than replacing with a rebuilt unit.
By "lucky" you must mean it is only going to cost me around $800? Between the gaskets and seals, machine work, and a water pump, that's what I will have in this repair. Never mind the labor! There goes my $500 a year budget!
David Teitelbaum
Yeah...ya could of had a cracked head, or two, damage from contaminated oil, etc...
(knock on wood)
David T
02-03-2013, 04:38 PM
I have the Motorola unit. The voltage regulator overheated and black goo dripped out. The charging light came on. I pulled the alternator and saw what happened. This is common on Lotus too. The potting compound melts and resolidifies inside the alternator. It gets into the brushholders and prevents the brushes from making full contact with the slip rings. Now the alternator stops charging. I took the whole thing apart and cleaned it up and replaced the voltage regulator and that fixed it for around $13. The reason this happens is because the alternator doesn't get enough cooling air and overheats.
David Teitelbaum
DMC5180
02-04-2013, 08:24 AM
The same thing happened to mine in 96. ( About 35K mi.) Right about the time Motorola parts were becoming extinct. Fortunately Rob Grady was able to source a Remanufactured Unit used on Jaguar. He had to swap the Front housing from my mine to make it work. It's being running fine ever since. I've got about 50K on the replacement unit now.
Are Motorola parts available again or did you just get lucky sourcing an NOS regulator?
... The reason this happens is because the alternator doesn't get enough cooling air and overheats.
David Teitelbaum
FWIW- AMC used to use the same basic alternator. The regulator and/or tiny diode trio feeding it was the cause of failure 90% of the time even on 6 and 4 bangers which had lots of air (Usually melted and smelly. Actually, most of them ran until the brushes wore out!)...Seemed like the breakdown/shorts of internal components had to be the problem.
(Grease ruining out of the bearings is a good sign of excessive ambient heat problems. Very rare.)
David T
02-04-2013, 01:06 PM
The voltage regulator crosses over to a VW unit. If you have it happen you should also go for the brusholder too. Not worth the trouble to clean it up. I did it but you have to unsolder the brushes and remove them so you can clean everything up and then you have to reassemble and resolder.
Getting back to the main topic, I put the heads on and was getting ready to fill with coolant. I use a coolant filler which creates a vacuum to draw the coolant in. I couldn't hold vacuum so I put a smoke tester on the cooling system and see smoke pouring out from the head gasket seam on the right head. Now tonight I guess I will have to pull that head back off and see why it didn't seal properly. At least the left head seems OK.
David Teitelbaum
dmc4087
02-04-2013, 02:13 PM
The voltage regulator crosses over to a VW unit. If you have it happen you should also go for the brusholder too. Not worth the trouble to clean it up. I did it but you have to unsolder the brushes and remove them so you can clean everything up and then you have to reassemble and resolder.
Getting back to the main topic, I put the heads on and was getting ready to fill with coolant. I use a coolant filler which creates a vacuum to draw the coolant in. I couldn't hold vacuum so I put a smoke tester on the cooling system and see smoke pouring out from the head gasket seam on the right head. Now tonight I guess I will have to pull that head back off and see why it didn't seal properly. At least the left head seems OK.
David Teitelbaum
Good find Dave- what spec did you torque the bolts to?
David T
02-04-2013, 03:15 PM
I used Josh's method of just torqung in steps of 20-50-80. It worked for the left side. Something is going on with that right head, it was the one that was leaking. I didn't check the head for flatness after getting it back from the machine shop and I only checked the liner protrusion, not the flatness of the block. The combustion chambers are sealed, I did a compression check and that was OK.
David Teitelbaum
dmc4087
02-04-2013, 06:18 PM
I wonder if any of the builders using a sealant as well as the head gasket? I'd be wary of this but I think I have read a few people experiencing leaks after head work.
David T
02-04-2013, 11:20 PM
I retorqued the head. It helped but it still leaks. In the meantime I tested several torque methods. Josh's step method ending at 80 ft/lbs is almost equal to the angle torque method. By my testing the angle torque gets you to about 85 ft/lbs. I guess I am going to have to pull the head and figure out why it won't seal. It is leaking on the upper end by cylinder #3. It was leaking on the bottom in the middle by cylinder #2 before I took it off. Maybe the gasket is bad? maybe a lot of silicone sealer will fix it up?
David Teitelbaum
^???^
NEVER use a sealant on a modern day head gasket! (Copper based was good for metal ones in the old days but silicone would never work in any case!) "The best thing to put on head gaskets is nothing" (APRA)
Never reuse a head gasket, even if you haven't fired the engine off, ever.
Never torque in steps IF the gasket manufacturer marked them "No Retorque"...ok to set the gasket with low torque <10 ft/lbs following the pattern, then torque fully, again following the pattern.
You didn't mention if you checked the head for warpage while you had it off...I bet the machine shop didn't do it unless you specifically asked them to...see if it is it listed on your ticket. (Old trick- set it on a known truly flat surface and see if a dollar bill will slide out from under it w/o drag...if it's as bad as it sounds, you will know it's time to take it back to the machine shop.)
It would be relatively rare for it to be the block.
It's very odd that the leak "moved"...it may have something to do with different torquing methods or re-torquing.
$.02
Follow the pattern using Josh's method with clean lightly lubricated threads (wipe with oil damp cloth, not dip) and a NEW gasket once you check out the surfaces... (Torque/angle/yield IS more accurate, but it relies on too many factors you can't guarantee, used parts, stretch, pre-stretch, etc, etc... best with blind holes where stretch can't be measured....)
bikergurl2000
02-05-2013, 03:19 PM
FWIW- AMC used to use the same basic alternator.
Saturn used a similar alternator too on their 1991 sedans.
Jeffu
02-05-2013, 03:38 PM
I retorqued the head. It helped but it still leaks. In the meantime I tested several torque methods. Josh's step method ending at 80 ft/lbs is almost equal to the angle torque method. By my testing the angle torque gets you to about 85 ft/lbs. I guess I am going to have to pull the head and figure out why it won't seal. It is leaking on the upper end by cylinder #3. It was leaking on the bottom in the middle by cylinder #2 before I took it off. Maybe the gasket is bad? maybe a lot of silicone sealer will fix it up?
David Teitelbaum
I am about to re-assemble my motor due to a head gasket leak similar to what you experienced. What began with a simple re-working of the heads has now turned into a full blown complete engine rebuild. So, I am following this thread in hopes of learning all that I can.
I don't know if this will help or not, but this is what I have been told by 3 or 4 different people in regards to head gasket installation on these motors. I have been told that these gaskets need to be installed "dry" with no other adhesive. Also, once the gasket(s) is installed and the head properly torqued it is very common for a small amount of coolant to seep/leak when performing an initial pressure test. However, after the motor has been started for the first time the seeping/leaking should stop after the engine has reached normal operating temperature up to 1 or 2x's.
Again I cannot speak from experience on this just yet. But, at least this is what I am preparing myself for once I get my motor installed. I wish you success on whatever you find out and please keep us posted.
-Jeff
Jason
02-06-2013, 12:18 AM
I don't know if this will help or not, but this is what I have been told by 3 or 4 different people in regards to head gasket installation on these motors. I have been told that these gaskets need to be installed "dry" with no other adhesive. Also, once the gasket(s) is installed and the head properly torqued it is very common for a small amount of coolant to seep/leak when performing an initial pressure test. However, after the motor has been started for the first time the seeping/leaking should stop after the engine has reached normal operating temperature up to 1 or 2x's.
-Jeff
When I rebuilt my engine after doing the cam break in run I had a tiny bit of seepage from the right head/block seam and a lot of seepage from the left head/block seam. I retorqued the left head, but left the right head alone, and haven't noticed any seepage since.
The heads were from Josh and the block surfaces were checked by a machine shop.
David T
02-06-2013, 04:21 PM
I took the right head back off last night and noticed the gasket was not being squashed along the upper edge like the lower edge, which was squashed tight. It got too late for me to check flatness (I got tired), I will do that tonite. The shop said they machined the head surface and took .013 off to get it flat and it looks machined. I know about not using sealant on head gaskets and how you are not supposed to reuse them but I have done it and gotten away with it a few times. I know about the dollar bill trick but I prefer to use a straightedge, surface plate and feeler gauges so I can measure any warpage and know exactly where it is. I considered running the motor and retorquing it but IMHO the leakage was more than it should be. I was concerned something was wrong with the assembly or maybe the gasket or the way I installed it.
All that and the fact that it is not all that easy to retorque and with the torque method and modern gaskets, you are not supposed to have to retorque. Besides, the left head is tight all around and not leaking. There is a retorquing method in the Workshop Manual. When parts don't fit together right it is usually a sign that you did something wrong. You should not proceed until you understand what is going on.
David Teitelbaum
I just can't see using silicon on a head gasket.
Back to the main deal... liner(s) cocked??
David T
02-06-2013, 10:40 PM
I am not sure yet what is going on but it isn't a problem with the liners. They never moved (I used liner locks when I removed the heads) and I get good compression. The leak is between the head and the edge of the block where it seals the cooling passages along the top edge between cylinders #2 and 3. Tomorrow I am going to measure it and try to see why it is not sealing. One possible option is to shim the gaskets with some gasket materiel along that edge and use silicone. I know it is not an "orthodox" or recommended fix but I have done it before on other equipment where I had problems sealing things up. If the block is warped there are not many options available short of replacement. I really do not want this to turn into a full-blown engine job. The short block itself and the crank, pistons, liners, seals, and rings are all in great shape if I do not disturb them.
David Teitelbaum
tgraham
02-07-2013, 01:24 PM
I use a coolant filler which creates a vacuum to draw the coolant in. I couldn't hold vacuum so I put a smoke tester on the cooling system and see smoke pouring out from the head gasket seam on the right head. Now tonight I guess I will have to pull that head back off and see why it didn't seal properly
Hi David,
I haven't read this whole thread in detail, so I could have missed something, but have you gotten the engine temp up hot enough to seal the gaskets?
When I rebuilt my engine and dropped it in, I also used a vacuum filler (then pressure-bled it, because I've never had a whole lot of luck with vacuum fillers on DeLoreans since it's such a big system - could be my compressor) and found a leak on one of the head gaskets around the same place you describe. After a minor freak-out and few choice words, I remembered that these head gaskets heat seal. After running the engine up to operating temp and back down, then re-pressure testing, everything was perfect.
FWIW, I also used the incremental torquing procedure (and the Volvo-updated torque pattern) on the head bolts.
Travis
David T
02-08-2013, 10:43 AM
I out the right head back on last night. Everything was very flat when I checked. I was able to use my coolant evacuator and got a good enough vacuum to pull it in. Once I filled it I pressurized the system and bled it. I didn't get much pressure when the left head started seeping so I only got to about 5 psi and bled it. I used some silicone sealer on the head gasket on the right side so it was sealed tight. I used the angular torque method but there is a drawback to it. You cannot properly check it for torque once torqued in that manner unless you know the ultimate torque spec. I have to admit Josh's method is superior in that respect. I torqued to 85 ft/lbs which I measured using the angular torque method previously. I am going to finish assembly and run the motor to "set" the gaskets like tgragham suggested and then pressurize to test for leaks. Before that I will retorque the heads and check the valve adjustments. I am now getting 130 psi + - 5% on all cylinders. Got to get the car ready for all of the St Patrick's day parades that are coming up!
David Teitelbaum
David T
02-13-2013, 12:08 PM
Motor is all back together. Got it started and ran it up till the fans cycled. The coolant leaks seem to have stopped, I have to pressure test it after it cools off. I retorqued the heads. Didn't need it. It DID need another valve adjustment which quieted the valves down a LOT.
Here is the important part. I torqued the heads using the angular method which worked out to 85 ft/lbs. The heads did not need to be retorqued. So here is my recommended method. Ist torque to 25 ft/lbs to set everything.You need to go this high to overcome the springs on any open valves. Do it in the alternating sequence proscribed. Step it up to 50 ft/lbs and then finish with 85 ft/lbs. You have to "chase" the threads in the block with a tap, Wire brush the threads on the bolts and put a SMALL amount of oil on the 1st threads of the bolt.
Do NOT try pressure testing the coolant system till you have run the motor for at least one fan cycle. I still have to check the timing, mech and vac advance and duty cycle on the Lambda. Do an oil change and clean up the engine bay. It appears tgraham got it right when he said to run the motor to set the head gaskets. I have done it in the past to retorque heads but I never had coolant leaks before (non-Deloreans).
David Teitelbaum
dmc4087
02-13-2013, 12:28 PM
Motor is all back together. Got it started and ran it up till the fans cycled. The coolant leaks seem to have stopped, I have to pressure test it after it cools off. I retorqued the heads. Didn't need it. It DID need another valve adjustment which quieted the valves down a LOT.
Here is the important part. I torqued the heads using the angular method which worked out to 85 ft/lbs. The heads did not need to be retorqued. So here is my recommended method. Ist torque to 25 ft/lbs to set everything.You need to go this high to overcome the springs on any open valves. Do it in the alternating sequence proscribed. Step it up to 50 ft/lbs and then finish with 85 ft/lbs. You have to "chase" the threads in the block with a tap, Wire brush the threads on the bolts and put a SMALL amount of oil on the 1st threads of the bolt.
Do NOT try pressure testing the coolant system till you have run the motor for at least one fan cycle. I still have to check the timing, mech and vac advance and duty cycle on the Lambda. Do an oil change and clean up the engine bay. It appears tgraham got it right when he said to run the motor to set the head gaskets. I have done it in the past to retorque heads but I never had coolant leaks before (non-Deloreans).
David Teitelbaum
My heads also weeped slightly before the engine warmed up the first time. Good to know it must be normal.
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.