PDA

View Full Version : Suspension Amsteer Lower ball joints.



Jeff K
01-23-2013, 02:45 PM
Are the current recommended lower ball joint replacements made by and Amsteer in the UK? I emailed them they said they have a pair for DeLorean. I got their name from a european DeLorean site.

I'm doing a front end restoration and wanted to replace them.

Thanks
Jeff

Delorean Industries
01-23-2013, 03:44 PM
Are the current recommended lower ball joint replacements made by and Amsteer in the UK? I emailed them they said they have a pair for DeLorean. I got their name from a european DeLorean site.

I'm doing a front end restoration and wanted to replace them.

Thanks
Jeff

I believe that is where ours come from. We can give you a competitive price shipped from the US.

Jeff K
01-23-2013, 03:53 PM
I believe that is where ours come from. We can give you a competitive price shipped from the US.

Ok, thanks Josh. Can you pm me on that.

chris williams
01-25-2013, 05:04 PM
Yes they are the ones, probably cheaper buying through a US vendor but from within the UK if you call them direct and quote the DeLorean Owners Club (UK) as per this thread: http://www.deloreans.co.uk/forum/viewtopic.php?f=20&t=4353 then they are priced at £55.00 plus shipping, however probably cheaper through a vendor in your country and it's better to support your local vendor.

On another note they have just produced a set of track rod ends (tie rod) for the DeLorean, exactly as per origional lenth/taper Etc Etc for me, They do come out slightly more expensive than some at £14.00 each but are exact perfect origionals. I can post some pics if anyones interested.

Chris

DMCH James
01-25-2013, 06:41 PM
Yes they are the ones, probably cheaper buying through a US vendor but from within the UK if you call them direct and quote the DeLorean Owners Club (UK) as per this thread: http://www.deloreans.co.uk/forum/viewtopic.php?f=20&t=4353 then they are priced at £55.00 plus shipping, however probably cheaper through a vendor in your country and it's better to support your local vendor.

On another note they have just produced a set of track rod ends (tie rod) for the DeLorean, exactly as per origional lenth/taper Etc Etc for me, They do come out slightly more expensive than some at £14.00 each but are exact perfect origionals. I can post some pics if anyones interested.

Chris

These are the same ones we have been selling for well over a year now - most of our dealers have stock on them.

http://store.delorean.com/p-7281-ball-joint-lower.aspx

Delorean Industries
01-25-2013, 11:24 PM
Available at dpi. Free shipping to USA via flat rate. Call to order for free shipping.

https://www.deloreanindustries.com/shop/lower-ball-joint-uk-style-upgrade.html

DCUK Martin
01-26-2013, 08:56 AM
These are the same ones we have been selling for well over a year now - most of our dealers have stock on them.

http://store.delorean.com/p-7281-ball-joint-lower.aspx

The price direct from Amsteer is per pair :umm:

international shipping on this given the size of the package won't be much.

Delorean Industries
01-26-2013, 09:45 AM
The price direct from Amsteer is per pair :umm:

international shipping on this given the size of the package won't be much.

Thanks Martin. We purchase through euro tech to support the club and pay 60 per unit I believe. Guess I need to go to the source.

DCUK Martin
01-26-2013, 10:33 AM
Sales tax (VAT) in the UK is 20% - if you check Chris' link above, the price is £55/pair incl vat. If you, as a company outside the EU, buy direct from a supplier who is VAT registered (I'd be amazed if Amsteer isn't), you shouldn't have to pay VAT because they'll book it out as a trade export. The price therefore will be closer to £46/pair not including any quantity discount ;)

Jeff K
01-26-2013, 12:55 PM
Thanks Everyone. I'm pulling the front end apart this weekend and I can determine what I need.

I know my bearings (which I have a replacement set) or Ball joints are bad. The left wheel has play in it.

I have a feeling my LCA's are trash, they look like they jacked the car up by them.. uugghh!

Jeff

chris williams
01-28-2013, 12:56 PM
Yes as Martin pointed out that price is per set of TWO, however as I wrote I think you should support the vendor that serves you best, usually in the country that you live in! As I mentioned above The company who are re-manufacturing the DeLorean ball joints as per this thread: http://www.deloreans.co.uk/forum/viewtopic.php?f=20&t=4353 Have just done the first set of track rod ends for the DeLorean (Tie-Rod) These are exact perfect origional both in Lenth/thread/ and taper that can sometimes be wrong on some of the X-ref's we use. Anyway these are the first ones and are now available to order from Amsteer. There not the cheapest at £14.00 each but are spot on. Just another option for everyone.
16075

David T
01-28-2013, 01:14 PM
Do they come with the original dust cover (boot) and if so is it available separately? Do they come with a grease fitting or at least a place to put one so you don't have to drill and tap a hole?
David Teitelbaum

chris williams
01-28-2013, 01:24 PM
Yes they come as shown in the photo, I'm sure if over time you need to renew the boot then they would supply them. The origionals never had a grease fitting (as far I am aware) so these have not, most of this type of item (Tie Rod/Track Rod) produced now, as I'm sure your aware does not have a grease nipple fitted anyway. Sealed for life I guess they call it!
Chris

David T
01-28-2013, 01:59 PM
Yes, they are "Sealed for Life" which really means since you can't properly grease them they will die and then their life is over. I drilled and taped the back plate so I could grease them. I didn't like using a needle under the boot. I didn't think I was getting enough grease where I needed it. I would be very interested in buying sets of dust boots for these tie rod ends. The boot I am using now doesn't fit all that great and certainly does not look original. Keeping the tie rod ends greased regularly allows them to last a LOT longer and having good boots will keep the dirt and water out and the grease in so they will last.
David Teitelbaum

DMC5180
01-28-2013, 02:33 PM
I'd like to know if lotus Engineers used Off-the-shelf Ball Joints and Rod Ends (borrowed from Lotus production) or Designed Unique Spec components.

chris williams
01-28-2013, 03:43 PM
As I understand it Amsteer did indeed design and produce the origional ball joints under contract to DMC, not sure about the Tie/track rod ends though.
Chris

A Van
01-29-2013, 07:55 AM
As I understand it Amsteer did indeed design and produce the origional ball joints under contract to DMC, not sure about the Tie/track rod ends though.
Chris


That is completely inaccurate.

Amsteer did not produce the original joints, part of our research into getting the joints remade involved tracking down the designer of the front suspension. Dr Mike Foxon.

The original joints were made by Armstrong Patents who no longer exist.

For this information and a whole lot more including a detailed measured comparison of the different joints available, by Darren Collins who is a respected classic car owner/restorer please read the 'definitive ball joint thread'

http://www.deloreaneurotec.co.uk/forum/viewtopic.php?f=13&t=2198&hilit=ball+joints

I would also say its unlikely anyone would be able to negotiate an export deal with Amsteer to avoid VAT.

BABIS
01-29-2013, 04:23 PM
http://www.ebay.co.uk/itm/DELOREAN-LOWER-BALLJOINT-/150983400249?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item23274fdb39 ;)

DCUK Martin
02-04-2013, 02:08 PM
Yes, they are "Sealed for Life" which really means since you can't properly grease them they will die and then their life is over.

Modern seals and greases are a far cry from what they were 30 years ago and are likely to be a load better in a modern remanufactured part from a respectable supplier than whatever you have loaded in your grease gun.

I've just got rid of my 2000 MY citroen with 256,000 on the clock and one each original track rod end and ball joint. Also had original CV joints and boots for whatever it's worth.



I would also say its unlikely anyone would be able to negotiate an export deal with Amsteer to avoid VAT.

Rubbish, it's not a matter of "cutting a deal" - no UK/EU supplier should charge VAT if exporting outside the EU! It's a fundamental principle of the tax system.

David T
02-04-2013, 03:31 PM
The outer shell of the ball joint is not hardened so you can't take any temper out of it by overheating it. If you overheated the grease then it will no longer lubricate the joint and the joint will fail quickly. My suggestion is to drill and tap a grease fitting into the back plate so you can easily grease it regularly. With regular greasing it can last a VERY long time. Ditto for the tie rod end (track rod). By being able to grease it you can also push out any dirt or water that may get into the joint. When you grease the joint you also inspect the boot (dust cover) for any tears, holes, or rips. At a minimum you should do it every 10,000 miles or once a year. The joint in the lower control arm takes all of the load so it is the one that will fail. The upper one lasts forever if the car doesn't get flooded or the boot damaged.
David Teitelbaum

A Van
02-06-2013, 05:15 PM
We spec'd grease nipples when the balljoints were made, you can have them made without...but seems pretty pointless to do that.

As your not VAT registered Martin, nor have you ever have been my knowledge of the UK VAT system is far deeper than yours.

Maybe my wording "deal" was wrong, to export net of VAT requires paperwork and an accountant who knows what they are doing as its more complex system than it appears, as Amsteer are a small family business it wouldn't be as straightforward as it seems.

DCUK Martin
02-06-2013, 06:14 PM
Alistair, I'm still staggered by your fascination with making anything you say to me a personal attack.

I have no appetite for a confrontation with you over something so blatantly obvious from 5 minutes googling (checking what I already knew anyway).

A Van
02-07-2013, 05:34 AM
We can all google anything Martin but in practice it's different than in theory,speaking from experience with the rules and the seller.
I have no interest in a confrontation either, just pointing out my post wasn't 'rubbish'.

chris williams
02-07-2013, 07:35 AM
Yes they come as shown in the photo, I'm sure if over time you need to renew the boot then they would supply them. The origionals never had a grease fitting (as far I am aware) so these have not, most of this type of item (Tie Rod/Track Rod) produced now, as I'm sure your aware does not have a grease nipple fitted anyway. Sealed for life I guess they call it!

Just to clarify to David T as they may have been some confusion. The track rod ends(tie rod) are not supplied with grease niples fitted however the Ball joints are. Apologies for any confusion caused. As can be seen in this auction: http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=200888194114 or direct from Amsteer as per this thread: http://www.deloreans.co.uk/forum/viewtopic.php?f=20&t=4353
Again apologies for any confusion caused.
Chris

DCUK Martin
02-09-2013, 12:07 PM
I apologise in advance to those for whom this has no relevance.


We can all google anything Martin but in practice it's different than in theory,speaking from experience with the rules and the seller.

The rules are there to be read, and they're pretty darned clear on the subject.


VAT is a tax charged on goods used in the EU, so if goods are exported outside the EU, VAT isn't charged. You can zero-rate the sale, provided you get and keep evidence of the export, and comply with all other laws.

http://www.hmrc.gov.uk/vat/managing/international/exports/goods.htm#6

This isn't some intricate complex tax fiddle, it has its roots in test-book macro economics (something I am qualified to talk about - if a bit rusty!).

It turns out you are correct to some level - there is one simple single page form which must be filled out once and can even be emailed in with no charge. This is a formality for any UK manufacturer to obtain an "EORI" code.

http://customs.hmrc.gov.uk/channelsPortalWebApp/channelsPortalWebApp.portal?_nfpb=true&_pageLabel=pageImport_ShowContent&id=HMCE_PROD1_029337&propertyType=document

Other than gaining this code, and in addition to standard accounting practice, they must simply keep proof of export - and my experience of this is that they must keep a record of the shipment - eg FedEx receipt.

Seems a complete no-brainer that no tax man would even raise an eyebrow at a UK manufacturer of auto components exporting a component specifically made for a car which predominantly exists in North America.

A Van
02-09-2013, 04:29 PM
My father is a retired HMRC employee with over 35 years service, I know the rules and have used them in my business dealings with a company in California, but when you get old fashioned companies who aren't used to exporting it becomes a different ballgame, that's the point I was trying to make.

easy now
05-21-2014, 08:41 PM
I apologise in advance to those for whom this has no relevance.



The rules are there to be read, and they're pretty darned clear on the subject.



http://www.hmrc.gov.uk/vat/managing/international/exports/goods.htm#6

This isn't some intricate complex tax fiddle, it has its roots in test-book macro economics (something I am qualified to talk about - if a bit rusty!).

It turns out you are correct to some level - there is one simple single page form which must be filled out once and can even be emailed in with no charge. This is a formality for any UK manufacturer to obtain an "EORI" code.

http://customs.hmrc.gov.uk/channelsPortalWebApp/channelsPortalWebApp.portal?_nfpb=true&_pageLabel=pageImport_ShowContent&id=HMCE_PROD1_029337&propertyType=document

Other than gaining this code, and in addition to standard accounting practice, they must simply keep proof of export - and my experience of this is that they must keep a record of the shipment - eg FedEx receipt.

Seems a complete no-brainer that no tax man would even raise an eyebrow at a UK manufacturer of auto components exporting a component specifically made for a car which predominantly exists in North America.

you really are a bawlwash

easy now
05-21-2014, 08:43 PM
Sales tax (VAT) in the UK is 20% - if you check Chris' link above, the price is £55/pair incl vat. If you, as a company outside the EU, buy direct from a supplier who is VAT registered (I'd be amazed if Amsteer isn't), you shouldn't have to pay VAT because they'll book it out as a trade export. The price therefore will be closer to £46/pair not including any quantity discount ;)

your ball joints are crap, no engineering to back them up, they are awful, if they fit, it's purely by accident

DCUK Martin
05-22-2014, 02:50 PM
you really are a bawlwash

I'll take your word for it. :dunno:


your ball joints are crap, no engineering to back them up, they are awful, if they fit, it's purely by accident

Er... I don't make ball joints.

I do fit the Amsteer ones though, as do all the main vendors now I believe.

chris williams
05-22-2014, 05:37 PM
your ball joints are crap, no engineering to back them up, they are awful
For the benefit of the DeLorean community who are using a lot of these Ball Joints supplied by Amsteer in the UK, could you clarify why you think they are crap? Have you had one fail on you? I'm sure all the owners running these would be interested to know for safety's sake. Thanks
Chris

NightFlyer
05-22-2014, 05:58 PM
For the benefit of the DeLorean community who are using a lot of these Ball Joints supplied by Amsteer in the UK, could you clarify why you think they are crap? Have you had one fail on you? I'm sure all the owners running these would be interested to know for safety's sake. Thanks
Chris

As far as I was aware, it is the go-to ball joint of choice - the Cadillac of ball joints.

DMCH's reproduction ball joints were the ones known for being of greatly inferior quality. Thus, I believe that they now sell the Amsteer, as do most of the vendors.

chris williams
05-22-2014, 06:03 PM
Indeed, I have them on my own car. Clearly though 'Easy Now' thinks they are no good and for everyones benefit I think we should know why? Perhaps they have had a failure that we are unaware off?
Chris

Mark D
05-22-2014, 06:12 PM
I'm pretty certain "easy now" is just trolling DCUK Martin as part of the fallout from their discusisons in other brake related threads. There are no known issues with the DMC club UK ball joints manufactured by Amsteer.

easy now incorrectly assumed that Martin had something to do with the design of the ball joints and was ripping on Martin using the same type of argument he felt Martin made against his front brake setup.