View Full Version : General Most Expensive Replacement Part You Didn't See Coming
LordFly
02-05-2013, 04:11 PM
Hi all! In the market for a D, and thought it would be a good idea to see what the most expensive "out of the blue" repairs people have required were. It might give me some good things to look for while shopping. Thanks.
WelmoedJ
02-05-2013, 05:02 PM
If you have done your homework, you will probably never have an out-of-the-blue repair.
However you will detect upcoming repairs while inspecting and driving the car prior to buying.
I knew I had to do something about the irregular behavior while accelerating (not gently, but in bursts going toward higher speeds).
I also knew I needed new tires and cooling system hoses (30 years old stuff).
I knew I had to repair or replace the cracked dash and binnacle vinyl.
At the end of my trip through the US I noticed an upcoming replacement of the clutch (engine revolutions didn't always match acceleration).
I also had reserved money for the new exhaust I wanted for this car.
Prepare yourself with the Buyer's Guide by James Espey.
It provides very helpful information about the car, its flaws and bad spots.
sdg3205
02-05-2013, 05:05 PM
Hi all! In the market for a D, and thought it would be a good idea to see what the most expensive "out of the blue" repairs people have required were. It might give me some good things to look for while shopping. Thanks.
You may have heard that DMC recently raised the prices on NOS parts. There are some parts, like say a frequency valve, you just pray never quit. I thin a FV goes for near $600 IIRC. It's about the size of an eraser but integral to K-jet function.
"Expensive" to me may also refer to seemingly insignificant parts that are pricey, or rare, like M7 bolts, trailing arm bolts, etc. Some parts you simply cannot obtain anymore and are valued at whatever you're willing to pay for it, or the seller is willing to let it go at. Left front fenders go for $2000 - $4000. It's all relative.
I just spent $300 on a clock. I attempted to fix it ($20) and then ended up ordering a near perfect replica from Maurice waaaaaay over in Amsterdam, IIRC. Originality and functionality have their price. Depends what you're going for.
DMCMW Dave
02-05-2013, 05:08 PM
Hi all! In the market for a D, and thought it would be a good idea to see what the most expensive "out of the blue" repairs people have required were. It might give me some good things to look for while shopping. Thanks.
The entire frame. An engine. An automatic transmission. Those are the big ones.
Jonathan
02-05-2013, 05:14 PM
If you don't understand the condition of your car when you buy it, the answer is simple: the frame (and many other things that go with that).
In terms of just "what are the most expensive parts", your stainless panels aren't cheap. I don't consider one of those ever being a surprise though as their condition is obvious. If someone drives into the side of your car and wrecks a panel that used to be fine, that is another subject all together.
Go to the webstore and find parts with prices of $0.00. Those are the expensive ones of a varying degree. Some you can live with. Some you can find a cross over that will work. Some you will be parking your car until you find one. I've never really heard of the 3rd option there happening, but I would guess it is technically possible. This is mostly true for parts they don't make anymore and once the inventory gets used up, it's harder to find a replacement. Luckily we have vendors and others making batches of NLA parts every so often. Things like headlight switches, estucheons, and torsion bars.
Don't worry too much about any switches, electrical odds and ends, valves and fittings, etc. Most all of that is not super expensive. Your big ticket items would be if you got a surprise hole in the VoD of your engine, or landed yourself a car with some interior pieces missing. A number of the interior trim pieces, consoles, etc. are not readily available.
EDIT: Nice one Dave, right on... haha, I was typing too slow :)
DeLorean
02-05-2013, 06:17 PM
Aside from already mentioned items, failure of something like the torsion bar for a door could happen right out of the blue, and be a nearly $1000 kick in the teeth... and is absolutely necessary for door function.
kajcienski
02-05-2013, 06:58 PM
I would also be curious as to the part that is the cheapest but pay a ton in labor. My rear main seal is about due and something like $1,100 (the labor estimate I was told) for a part that is just over $10.
kajcienski
02-05-2013, 06:59 PM
Aside from already mentioned items, failure of something like the torsion bar for a door could happen right out of the blue, and be a nearly $1000 kick in the teeth... and is absolutely necessary for door function.
That's okay, you can just crawl through the window ;)
DMCMW Dave
02-05-2013, 07:20 PM
I would also be curious as to the part that is the cheapest but pay a ton in labor.
The winner on that one, at least on a percentage basis, has to be the manual transmission second gear roll pin. The part itself is LESS THAN $1. But you take the trans out of the car and take it apart. And generally do the clutch while you are in there.
Your automatic rear main is a close second. Be sure to have the torque converter seal done at the same time. It's another $10 seal that you can't get to. :D
Rich W
02-05-2013, 07:22 PM
I would also be curious as to the part that is the cheapest but pay a ton in labor. My rear main seal is about due and something like $1,100 (the labor estimate I was told) for a part that is just over $10.
IIRC, the "roll pin" or shear pin (or whatever the real name is) that often fails with the shifting mechanism for the manual transmission
is very inexpensive (two bits or less?) but replacement and re-adjustment of the shifter is comparably expensive.
Back in the day, Dave Swingle started installing a pin-inside-a-pin to increase the strength of this part...maybe he still does? Dave?
LordFly
02-05-2013, 07:26 PM
Great, thanks guys! From the sounds of it, I may just be over-thinking it. It is still "just a car" after all. as long as there are no "oh this part goes all the time and is $1500" kinda things, I will just treat it like any other car purchase. Look everything over as thoroughly as possible and hope for the best.
DMCMW Dave
02-05-2013, 07:30 PM
Back in the day, Dave Swingle started installing a pin-inside-a-pin to increase the strength of this part...maybe he still does? Dave?
I still do. Idea shamelessly stolen from Rob Grady.
DavidProehl
02-05-2013, 07:30 PM
Aside from already mentioned items, failure of something like the torsion bar for a door could happen right out of the blue, and be a nearly $1000 kick in the teeth... and is absolutely necessary for door function.
This one happened to me within my first year of ownership. It blew out while driving. Sounded like a shot gun and I nearly had a heart attack. That got me to the side of the road with the engine off in a big hurry. I was very lucky to find that a local owner had an extra used driver's bar and was willing to sell it.
David T
02-05-2013, 09:12 PM
When buying a used car you should inspect it to ascertain it's condition so you know what it's value is and what work, if any, needs to be done. For the most part, if you are allowed to properly inspect the car, you can know it's condition. The main thing is you want to know about the big, expensive stuff so you are not surprised with a huge repair bill soon after buying the car. Some of the things you cannot know for sure about include:
The clutch (on a 5-speed)
The motor unless you are allowed to do a compression test
Now this is no guarantee that a fuel pump won't fail soon, a coolant hose won't pop, the water pump won't start leaking, a battery won't go dead, etc.
The main thing about the inspection (a PPI or a Pre Purchase Inspection) is that it is done by a person who is intimately knowledgeable with a Delorean and all of it's systems. They have full access to the car and can test drive it and if available, review it's service history. They will know where to look for hidden problems, what updates the car has (if any) and how a Delorean is supposed to operate. They will know what it will cost to fix any problems found and be able to give you a very good estimate of the car's value. This kind of intensive inspection doesn't come cheap but what is peace-of-mind worth when you are spending a lot of money? Even with a through PPI you should still budget something for unforeseen repairs. Don't spend your last penny buying and insuring the car leaving nothing left over.
BTW, the pin in a pin trick is standard procedure on the Lotus UN-1 tranny so I don't think Rob can claim "inventing" it. Maybe credit for using it on the Delorean. On the Lotus they also do that on the output flange on the final drive. And fill it with silicone sealer to keep it from leaking.
David Teitelbaum
rddmc
02-05-2013, 09:20 PM
Hi all! In the market for a D, and thought it would be a good idea to see what the most expensive "out of the blue" repairs people have required were. It might give me some good things to look for while shopping. Thanks.
Based upon my experience with VIN 6032, I would check the condition of the frame first.
Rod
10921
Delorean Industries
02-05-2013, 10:10 PM
Based upon my experience with VIN 6032, I would check the condition of the frame first.
Rod
10921
Total piece of mind when purchasing from DPI. Our frames are completely refurbished with nothing left out.
Nicholas R
02-05-2013, 10:22 PM
BTW, the pin in a pin trick is standard procedure on the Lotus UN-1 tranny so I don't think Rob can claim "inventing" it. Maybe credit for using it on the Delorean. On the Lotus they also do that on the output flange on the final drive. And fill it with silicone sealer to keep it from leaking.
David Teitelbaum
I dont understand why would you need to double those roll pins. They're hardly in shear at all. There's no way you're going to spin the flange on the splines, the only thing they do is hold the flanges in place. They're barley subjected to any shear at all since only an inward/outward load will affect them. That loading is very unlikely since the DeLorean doesn't have stressed half shafts, as the CV joints absorb all shaft plunge.
On a side note, if you install Toby's bulletproof input shaft coupler he includes a "spiral" roll pin, which is essentially a piece of sheet metal tightly rolled into a spiral used in place of a roll pin.
DMCMW Dave
02-06-2013, 12:21 AM
On a side note, if you install Toby's bulletproof input shaft coupler he includes a "spiral" roll pin, which is essentially a piece of sheet metal tightly rolled into a spiral used in place of a roll pin.
Unfortunately I believe you got the last one of those.
jawn101
02-06-2013, 12:26 AM
The winner on that one, at least on a percentage basis, has to be the manual transmission second gear roll pin. The part itself is LESS THAN $1. But you take the trans out of the car and take it apart. And generally do the clutch while you are in there.
Your automatic rear main is a close second. Be sure to have the torque converter seal done at the same time. It's another $10 seal that you can't get to. :D
Second this... My 2nd gear roll pin was like 46 cents from Dave, but it turned into a full engine and transmission pull, transmission overhaul, complete engine tear down, new clutch...I probably spent 2000 bucks on parts alone, and it took me and two other owners weeks and weeks to complete the job. Would have been way worse if I'd paid a shop to do the work (though probably faster)
DeLorean03
02-06-2013, 01:43 AM
Auto transmission. Mine had a problem where it was starting to ever so very slightly slip if "cruising along" through a parking lot and you wanted to give it a lil' gas to "get up and go".
$4000 later, DMC-MW had it all taken care of.
And they did NOT just stick a brand new one-piece all new auto transmission in.
They put in part #4 on this page:
http://store.delorean.com/c-386-4-5-0-assemblygasket-sets.aspx
Plus the labor to do it.
And they a 100% fantastic job.
Jonathan
02-06-2013, 02:04 AM
Would have been way worse if I'd paid a shop to do the work (though probably faster)
Another way of looking at this came to mind. And that is this trade off between do it yourself versus pay someone else to do it. Your labor time is free, sort of. The mechanic at the shop is $80 per hour or somewhere in that ballpark. The part that I was considering though was how some jobs are worth taking to someone else.
Two that came to mind are the fuel accumulator and the exhaust manifold gaskets.
The fuel accumulator kit was around $100 I think (may have changed by now), but is not in a very user friendly and accessible spot. Dead centre under the the car. Add to that you are working on a pop can size item through an opening the size of a DVD case, and you're trying to get 30 year old rusty fittings loose. If all goes well, you may get off with just a face full of fuel. If you can put the car on a lift, it isn't quite as bad. I did a trial run on mine and was able to get about 13" clearance. That's not a lot of room between the car and the garage floor for your head to go, your arms and hands and your stubby wrenches. Not to mention some paranoia with the nerves fearing being under the car. All of that added up to my mechanic getting that job. Part of the trade off was one of my fuel lines springing a pin hole leak, possibly caused by someone inexperienced in DeLoreans twisting and not realizing it. Good thing though as he put a nice new section of fuel line in for me, a job I would not have had the stuff for at my disposal at home. Add it all up and it was about $220 labor/misc charge from the shop. That was okay with me.
The exhaust manifold gaskets is the other significant job I have given to a shop. I believe the rule of thumb is 4-6 hours to change the gaskets and an extra hour for each stud you snap off. Another job easier on a lift than on ramps at home and having a lot of the right tools isn't a bad idea either. This was one I likely could have tackled myself, but was happy paying someone else to do it once we saw the PO work on two of those stud holes that needed attention. Again, $100 for so for the kit, but more than that amount in time and effort to install it.
Anyway, just another perspective to consider. Much of which depends on what sort of work space you have at home, tools, and your expertise or comfort level. Some things are great for anyone to give a shot at tackling. Other things, like brakes, are a greater risk of consequence if you mess it up.
Dangermouse
02-06-2013, 09:38 AM
I would have to go with the torsion bar for "something you don't see coming". You could argue that a transmission gives you some warning that it;'s heading south, but the bar just breaks one day (if you are unlucky).
Of course many, many cars still have their original bars (and infact almost all bars are original) without any issues whatsoever, but it it has been over torqued, or nicked in some way........................
LordFly
02-06-2013, 11:12 AM
I would have to go with the torsion bar for "something you don't see coming".
DMC lists $850 for the RH and $0 for the LH :( But like you said, most are original, and it's not something you can really inspect anyways. They're either good, or they're broken. I'll permanently cross my fingers for the torsion bars ;)
DMCMW Dave
02-06-2013, 11:25 AM
DMC lists $850 for the RH and $0 for the LH :( But like you said, most are original, and it's not something you can really inspect anyways. They're either good, or they're broken. I'll permanently cross my fingers for the torsion bars ;)
The DMOCO lefts are available again. I believe they are $950.
DeLorean03
02-06-2013, 11:41 AM
You could argue that a transmission gives you some warning that it;'s heading south
Well, when the transmission was first completely rebuilt in 2003 at the tune of $3200.28, I "didn't see it coming" when it started acting up only 8 years later (: ...
DeLorean
02-06-2013, 12:32 PM
The DMOCO lefts are available again. I believe they are $950.
When I bought my RH one 2+ years ago, it was $450 from DMCH. I guess they must be running low on the NOS ones now being that there was almost 100% price increase on those...
AugustneverEnds
02-06-2013, 12:42 PM
Front frame crash extension. My car had been lowered WAY down by the PO and I hit a nasty pothole which caused the front extension to pierce the radiator necessitating a new one and $1,000 in labor at the body shop to fix the extension. Total cost for radiator, installation, frame repair $1,520. :angry:
David T
02-06-2013, 03:39 PM
On the Lotus I am guessing but the reason the pin is doubled up for the output flange is because of all of the torque. Even with splines the flange can move ever so slightly and that is enough to bend the pin. Another oddity is the hole is not drilled dead center. If you put the flange on (on the Lotus) 180 degrees off, the hole will look lined up but you will never get the pin in. On the Lotus V-8 you are pushing over double the torque of a Delorean.
David Teitelbaum
SIMid
02-06-2013, 06:19 PM
Rebuild Kit for the Auto $400+
Getting the box rebuilt with rebuilt torque converter $2500
New second drum $350
Labour to pull the box out and putting it back in $600
New hose kit $300+
Nicholas R
02-06-2013, 06:54 PM
The DMOCO lefts are available again. I believe they are $950.
On the topic of torsion bars, has anyone ever tried one of these?
http://deloreannewparts.com/store/page11.html
jawn101
02-06-2013, 08:04 PM
On the topic of torsion bars, has anyone ever tried one of these?
http://deloreannewparts.com/store/page11.html
Really good question. I wanna like it because there are very few options, but boy is it ugly. :)
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.