View Full Version : Print your own Binnacle or LFF !
Dangermouse
02-06-2013, 04:56 PM
Did you watch James Bond in Skyfall?
Did you shed a tear when the Aston Martin was blown up? I did, even though I knew it wasn’t real. I had guessed CGI, but No.
But here’s how they did it.
http://www.3ders.org/articles/20121107-voxeljet-builds-aston-martin-models-for-james-bond-film-skyfall.html
Yes, they 3D printed all the body panels for a DB5 and attached them to a steel frame.
So, in theory, you could print a new Binnacle (or even a LFF, assuming you had a painted car of course).
thirdmanj
02-06-2013, 05:56 PM
Houston... We have a binnacle.
Jeff K
02-06-2013, 06:20 PM
Did you watch James Bond in Skyfall?
Did you shed a tear when the Aston Martin was blown up? I did, even though I knew it wasn’t real. I had guessed CGI, but No.
But here’s how they did it.
http://www.3ders.org/articles/20121107-voxeljet-builds-aston-martin-models-for-james-bond-film-skyfall.html
Yes, they 3D printed all the body panels for a DB5 and attached them to a steel frame.
So, in theory, you could print a new Binnacle (or even a LFF, assuming you had a painted car of course).
This IS the future. When you need a part/panel.. you will pay a fee to use the digital CAD representation to 3d render it. It's going to be as revolutionary as the computer and automobile.
SIMid
02-06-2013, 08:05 PM
That was pretty awesome! Thanks for posting! :)
DrJeff
02-06-2013, 09:00 PM
With all the excitement in getting 3D printed components, I thought I'd share some photos of some components I've modeling, printed, and fitted to the Delorean. One of my many current projects is to shift the stock a/c vents from the center console (to make room for a touchpad) and from the door (just to make damn sense) to the kneepads (as seen in the DMC-EV prototype). Rather than use modern vents I wanted to reuse the stock vents as they are more in keeping with the look and feel of the car. All the vents needed slight modification, but mods from which there is no going back!
I closed off the two center vents and connected hose to route the outlets from the two bottom vents to the two vents in the LH kneepads and the RH kneepads, respectively. The challenge then was to connect the hose (a standard 2.25in) to the back of the vents. To solve that problem I created mm accurate models using TinkerCad.com and had them printed by Shapeways.com. The printed 3D objects are lighter than you would expect, but the plastic is very strong and pretty stiff.
Here are the photos...
16369163701637116372163731637416375163761637716378 16379
Once I get through this set of projects I'll post some PDFs with all the photos/instructions I've collected.
Other 3D printed object projects I'm doing...
- 3rd brake light housing (no one has mounted one here before :)
- Replacement mount location for the center console buttons (my center console is very custom)
- steering wheel logo (in stainless steel - shown in another post)
The 3D printing is not without restrictions. For all but industrial scale printers you're limited on the size of the object. For non-industrial about 12 inches is the max. The designs also have to follow certain rules - wall thickness, etc, which can vary depending on the material you select. Printing is a scanning like process (think early day dot matrix printing) and you can get aliasing issues. Overall I'm pleased with what's possible. It's not cheap, but it is cheaper than buying a 3D printer (about $3000) and you can access more print materials (home printers can do one or two plastics). The vent joints (all 4) cost me $77 including shipping, but for cold air directly on the passengers... priceless.
If you're interested pm me and I can send you the object model file so you can modify or print your own.
Jeff
dmcjohn
02-06-2013, 10:42 PM
Nice work Jeff!
You know, considering all the CGI these action movies have nowadays, you'd think they'd have just made a CGI Aston Martin and digitally blown that up. Physics engines are amazingly realistic nowadays, and it would've allowed them to do even more crazy shit to the Aston Martin in future movies. I would've thought they'd have already done this by now.
Rhsxo
02-07-2013, 02:03 PM
Let's just say you wanted to "print" a LFF, how much would it cost?
If the cost is low enough, that means you could theoretically produce any car. DeLorean, Tucker, Model T, it wouldn't matter.
DMCMW Dave
02-07-2013, 02:59 PM
Let's just say you wanted to "print" a LFF, how much would it cost?
.
What would you do about the fact that the "printed" fender would be made of soft plastic?
DrJeff
02-07-2013, 03:49 PM
Let's just say you wanted to "print" a LFF, how much would it cost?
If the cost is low enough, that means you could theoretically produce any car. DeLorean, Tucker, Model T, it wouldn't matter.
Stainless steel is $8 per cm3 on shape ways.com. So it would be quite expensive.
nullset
02-07-2013, 03:56 PM
I do have a few ZCorp 3D printers. If anyone would like some prints, let me know.
The material is a plaster like material. I can also print molds and then cast in to those to make a final product.
It's a fun hobby!
btw, how do you get a whistle from Germany to New York in 45 minutes?
A 3D printer!
Someone in Germany designed a 3D printable whistle, and uploaded it to thingiverse. Someone in New York then downloaded the model and printed it. Less than an hour....
--buddy
Jason
02-07-2013, 05:38 PM
So, does anyone happen to have a 3D cad model of the binnacle?
I was thinking of trying to make a binnacle out of Delrin or some other machineable plastic using a CNC mill, but my skills at making cad models of curvy things aren't so good.
DrJeff
02-07-2013, 06:58 PM
So, does anyone happen to have a 3D cad model of the binnacle?
This might be your best bet... http://www.123dapp.com/catch#catchApps
Using lots of photos taken from different angles under consistent lighting, from which the tools can then construct a 3D model. I haven't tried it yet, but it sounds interesting, especially for something like the binnacle.
SIMid
02-07-2013, 09:25 PM
Using lots of photos taken from different angles under consistent lighting, from which the tools can then construct a 3D model. I haven't tried it yet, but it sounds interesting,
Uncracked one would be good. :smashfreak: :lol:
TTait
02-12-2013, 11:57 PM
What would you do about the fact that the "printed" fender would be made of soft plastic?
You can "print" in Stainless Steel today - the material can be polished so presumably it could be grained. Further, if you do want a fender, you can probably print a structural underlayment for the stainless in a less expensive material, and then print on a thinner stainless skin.
In the future? It may also be possible to use the "printer" to partially refurbish existing parts at some point. Print in a stainless plug in an antenna hole? Print out small dings in stainless? You would probably have to drill a small hole first to help promote mechanical adhesion.
DL4567
02-13-2013, 12:20 AM
We are well on our way to this:
http://2.bp.blogspot.com/-RcM3z_zSo0w/TVfWgUxbREI/AAAAAAAAAXg/zUCfyrvLV_o/s1600/star%2Btrek%2Breplicator2.jpg
http://img.scoop.it/rSoBqUHPjY-G8gmwuGIx5jl72eJkfbmt4t8yenImKBVaiQDB_Rd1H6kmuBWtc eBJ
Not to rain on anyone's parade, but as far as I'm aware, there is no 3D Printer with a print area large enough to print LFF's in any material, let alone a rare exotic like stainless steel. All things considered, it would make much, much more sense to grab a piece of appropriate 304 grade stainless steel and craft it into a LFF as seen here (http://pjgrady.co.uk//GenericContent.aspx?PageType=Delorean_Repairs&ShowContent=Project_17_Reproduce_left_Front_Fender .html).
The binnacle may be a different story, but frankly, do you really want a cheap-looking plastic binnacle? 3D printers tend to have a nasty habit of having very visible lines showing where each layer of extruded material is, particularly if they do not have a heated bed. In a DeLorean, this would look like ass, and I can't imagine anyone would trust the same kind of plastic that deforms under the heat of the headlights to retain its shape directly in the sunlight of the arguably hotter cabin. I don't know about you, but I don't want plastic melting all over the instrument cluster internals.
nullset
02-13-2013, 01:01 AM
Shep,
Not all printers are FDM, and some of them have incredible resolution. The technology is coming along!
There are plenty of ways of making things:
-Molding and casting
-3D scanning and printing
-Manually modeling a physical object, then 3D printing
-CNC machining
-Hand making it using hammers and saws!
There's no reason that, a few years from now, it won't be possible to produce a new LFF from a design. It'd be EXPENSIVE, though.....
Jay Leno famously uses 3D printers to make reproduction parts for his cars.
http://www.popularmechanics.com/cars/jay-leno/technology/4320759
It's a really fun technology. If someone can design a part, I'd be happy to print it. I can then mold and cast and could mass produce things.
--buddy
Dangermouse
02-13-2013, 09:55 AM
Not to rain on anyone's parade, but as far as I'm aware, there is no 3D Printer with a print area large enough to print LFF's in any material,
.
Shep,
do you read the initial post? That's exactly what they did for the A-M.
SIMid
02-13-2013, 06:28 PM
I had a brainwave the other day ...............
As we all know the fuse boxes get quite hot on some cars, is there a way to make a new fuse box cover and incorporate 2 PC fans into the top to either pump air in or pull air out to keep the temp at bay?
There's no reason that, a few years from now, it won't be possible to produce a new LFF from a design. It'd be EXPENSIVE, though.....Therein lies the problem: expense. It'll take years, possibly decades, before it would be cost effective to print a binnacle or LFF vs. getting a spare one from a parts car (or, in the case of the binnacle, getting a reproduction from DMCH or a recovered one from DMC California). Don't get me wrong, I love 3D printing technology, but currently this only feasibly works in small scale. Printing an early shifter knob, for example, makes much more sense and depending on your setup and pricing may provide a bit of a return on investment, particularly as quantity increases. As far as I'm aware, no one has any of those NOS either. 3D Printing is still a developing technology, and costs seem to be steadily decreasing as time goes in (particularly for the RepRap models), so I have no doubt that somewhere down the road it will be a viable option to print a LFF or binnacle.
Until, of course, some jackass prints a bunch of them and the competition lowers the selling price to the point of it being unfeasible again.
Shep,
do you read the initial post? That's exactly what they did for the A-M.I did, but size is still an issue. The print bed size required by the Aston Martin is about 1/4th that of what a LFF would require, and the LFF is very long. Not to mention the Aston Martin was produced in pieces and not as one solid piece like a LFF would require (necessitated by the fact that it needed to accurately go "boom", whereas the LFF needs to be one solid piece).
Dangermouse
02-13-2013, 07:51 PM
They don't give dimensions but if they printed the whole full scale car in 18 pieces, some of them must have been a decent size. That A-M LFF looks pretty long.
Their initial plan seems to have been to print the whole car in one piece at 1/4 th scale.
However, clearly expense wasn't an issue, so who know what it cost. (I read that one of the models sold for $100000 after the movie premiered).
Of course it will be a long time before you and I can pop into 3DPrints-R-Us, load in our digital file and have a latte while it is created. But maybe under 10 years ?
Of course it will be a long time before you and I can pop into 3DPrints-R-Us, load in our digital file and have a latte while it is created. But maybe under 10 years?I'll be waiting! :cheers:
Farrar
02-14-2013, 12:24 AM
I have wondered for a long time if DMCH doesn't have a 3D printer (and if not, why not). There are all sorts of fiddly little things I'd like to get my hands on, like connectors and whatnot. Instead, I've had to find cross-references or invent my own. I imagine a 3D printer would be a good investment for any antique car parts retailer, if they can justify the initial expense.
ramblinmike
02-14-2013, 12:31 AM
I have wondered for a long time if DMCH doesn't have a 3D printer (and if not, why not). There are all sorts of fiddly little things I'd like to get my hands on, like connectors and whatnot. Instead, I've had to find cross-references or invent my own. I imagine a 3D printer would be a good investment for any antique car parts retailer, if they can justify the initial expense.
Hi Farrar. Long time, no read.
I have wondered for a long time if DMCH doesn't have a 3D printer (and if not, why not). There are all sorts of fiddly little things I'd like to get my hands on, like connectors and whatnot. Instead, I've had to find cross-references or invent my own. I imagine a 3D printer would be a good investment for any antique car parts retailer, if they can justify the initial expense.3D printers are geared more for individual use than mass production. The cheaper ones in particular (RepRap, Makerbot, etc.) need to be monitored to ensure they're operating correctly and efficiently, as they often need maintenance (oiling, fixing broken plastic, correcting misalignment, or even fixing catastrophic failures). As you start getting more and more expensive, maintenance is usually lessened, but return on investment becomes increasingly out of range, and in some cases the print quality actually worsens. Heated beds do wonders for extruder-based printers, but usually the more "commercialized" machines don't have them since they get really damn hot and can cause burns if you're impatient. Powder-based printers have nearly flawless print quality (as used for the Aston Martin), but are astronomically more expensive than extruder-based printers, again going back to the return on investment issue.
I'm not sure any 3D printer could help with connectors though. I'm not aware of any currently on the market that can mix metal and plastic in the manner you're describing. Circuitboards I've seen, and small metal parts even, but I can't say I've seen metal and plastic mixed.
Farrar
02-14-2013, 01:20 AM
No need. The metal bits are on the ends of the wires, which stick into the plastic connectors.
No need. The metal bits are on the ends of the wires, which stick into the plastic connectors.Don't you need to fabricate the pins and sockets? I've never seen wire that came with the metal part of a connector pre-attached unless it was already part of one previously.
DMCVegas
02-15-2013, 01:49 AM
Don't you need to fabricate the pins and sockets? I've never seen wire that came with the metal part of a connector pre-attached unless it was already part of one previously.
No, not at all. You just have to attach the pins and sockets yourself.
First you have the plastic connectors, both male and female. From there you have the pins and sockets. These are either crimped or soldered onto the ends of wires. Then you just slide the pins and sockets into the back of their respective connectors where they lock into place. Then just plug the connectors together and you're done. If you either built a harness from scratch or simply had to repair a damaged connector, this is all that you'd have to do. Not difficult at all. In fact, here is a video showing how to assemble RS-232 cables. Just apply the same practice to the any of the connectors in the DeLorean.
http://www.youtube.com/watch?v=DFCEc6Tr6w8
nullset
02-15-2013, 12:07 PM
This article showed up recently, and makes a lot of very valid and interesting points.
http://blog.makezine.com/2013/02/14/3d-printing-revolution-the-complex-reality/
DCUK Martin
02-17-2013, 02:35 PM
I see and use 3D printed parts on a daily basis. The only materials that are comparable with injection moulded plastic parts are the SLS powders and the machines and powder cost a fortune and have a fairly poor tolerance. Objet and SLA are more accurate but also much more brittle.
DMCVegas
02-18-2013, 03:46 AM
Very interesting article, and all very valid points. I don't however think that as 3D technology improves and more people have access to them that people intend upon creating their own CAD designs anyway. Most likely what they'll be doing is simply obtain the designs and print out their pieces accordingly. I believe that the RepRap project is the one in question where funding to a group was pulled when the developed plans for small firearm pieces to be printed. The motivation would be that rapid printers could crank out firearms in 3rd world countries in order to help citizens arm themselves against oppressive regimes or something like that. Eventually though they pulled funding for that particular group. The guns of course would be limited use only before they became damaged by heat, but would work long enough to get the job done. Knives as well can also represent the dark side of things here, but so it goes with anything.
I think that 3D printers are fascinating and offer up solutions that we can't even realize just yet. Especially as the technology improves. I don't think that they'll ever take the place of die casting or injection molding of course. It'll be easier, quicker, and cheaper to go to the store to pick up some plastic cutlery for a party than to wait around while you print some sporks out. But it does offer fantastic possibilities for remote locations that do not have access to deliveries in a timely manner. From temporary car parts to perhaps even medical instruments for field hospitals triages, I think that 3D printers will change the world.
videobob
02-18-2013, 11:49 AM
We work with fiberglass here at my shop all the time, it wouldn't be a big deal to make a binnacle out of fiberglass and painted or wrapped in material...
DMC5180
02-18-2013, 09:10 PM
We work with fiberglass here at my shop all the time, it wouldn't be a big deal to make a binnacle out of fiberglass and painted or wrapped in material...
I'm actually surprised no one has done this yet. As stated once the mold is created you make the parts on demand. Kinda like DMCH's fiberglass front facia's.
pgringo
02-20-2013, 11:48 PM
has anyone done a binnacle in carbon fibre?
DavidProehl
02-27-2013, 02:25 PM
Here is a guy aiming to build production cars using 3D printers:
http://www.wired.com/autopia/2013/02/3d-printed-car/
(http://www.wired.com/autopia/2013/02/3d-printed-car/)
Takes 2,500 hours to print a car right now, but over time this may become quick and cheap enough to do on a large scale. If we could 3D print with molten stainless that would be awesome.
Here is a guy aiming to build production cars using 3D printers:
http://www.wired.com/autopia/2013/02/3d-printed-car/
(http://www.wired.com/autopia/2013/02/3d-printed-car/)
Takes 2,500 hours to print a car right now, but over time this may become quick and cheap enough to do on a large scale. If we could 3D print with molten stainless that would be awesome.Reading the article, the prototype was estimated to cost $50,000 , although it doesn't specify how much of that cost was 3d printed plastic and how much, if any, was vitamins (e.g. drivetrain, glass, electronics). Doesn't seem very practical though, having only ten horsepower. It'll be interesting to see how that turns out, but hopefully they don't completely follow in Aptera's footsteps, considering how Aptera went into receivership and all.
Dangermouse
02-28-2013, 09:08 AM
2500 hours! There will be a Morgan-esque waiting list then.
Did you catch the linked article at the bottom of the page, entitled:
3D-Printed EV Racer Hits 88 MPH, Doesn’t Go Back to 1955http://www.wired.com/autopia/2012/08/3d-print-ev/
bringing this thread back full circle :o
Dangermouse
02-28-2013, 11:28 AM
This just in - 3D printing is so last year.
4D is where it's at: 4D printed objects 'make themselves'
http://www.bbc.co.uk/news/technology-21614176#
Powered by vBulletin® Version 4.2.5 Copyright © 2026 vBulletin Solutions Inc. All rights reserved.