Log in

View Full Version : How to wire flux storage compartment door



DMCflux
02-08-2013, 08:34 PM
Im looking for a 'how to' wire flux capacitor storage door to one of the spare blank switches in the center console?

DMC5180
02-10-2013, 06:14 PM
Im looking for a 'how to' wire flux capacitor storage door to one of the spare blank switches in the center console?

Are you intending on keeping the rocker switch that's in the flux door?

DMCflux
02-10-2013, 06:54 PM
Are you intending on keeping the rocker switch that's in the flux door?
Yes, I would like to have it hardwired with a connector so I can remove the door and still have it operate with the switch. It looks like there is some sort of input on the back of the door, I don't know what male connector would fit it or how to hardwire it to a switch in the vehicle.

Dangermouse
02-11-2013, 09:57 PM
So are you looking at an either/or scenario, where either the door switch or the console switch will turn the FC on, or are you intending to move the functionality of the door switch to the spare console switch and just have one switch.

DMCflux
02-11-2013, 10:08 PM
So are you looking at an either/or scenario, where either the door switch or the console switch will turn the FC on, or are you intending to move the functionality of the door switch to the spare console switch and just have one switch.

Either or scenario. I would like to have both options

Dangermouse
02-11-2013, 10:26 PM
Disclosure - I don't have an FC, so I am asking basic questions.

Is the existing switch actually mounted on the door? If so, and you want to completely remove the door hen you would need to plan on moving that switch to the side wall. If your FC is one of those located in the cubby, then that may be a problem.

Can you see where the wires from the existing switch terminate inside the FC? Is it on a terminal block?

Pictures might be useful.

Did the FC come with an installation wiring diagram that you can post?

What I am trying to get at here, is that in its simplest form, you should be able to run two wires from the blank switch and connect them in parallel with the existing switch at a terminal block, if one exists.

DMCflux
02-11-2013, 11:05 PM
Disclosure - I don't have an FC, so I am asking basic questions.

Is the existing switch actually mounted on the door? If so, and you want to completely remove the door hen you would need to plan on moving that switch to the side wall. If your FC is one of those located in the cubby, then that may be a problem.

Can you see where the wires from the existing switch terminate inside the FC? Is it on a terminal block?

Pictures might be useful.

Did the FC come with an installation wiring diagram that you can post?

What I am trying to get at here, is that in its simplest form, you should be able to run two wires from the blank switch and connect them in parallel with the existing switch at a terminal block, if one exists.

No diagram. Switch is on the back next to what looks like an input for a connector. I'll take pics
tomorrow.

Tillsy
02-12-2013, 02:54 AM
Switch is on the back next to what looks like an input for a connector.

That isn't an input, it's the frequency control. Use a small screw driver to adjust the speed of the flux...

DMCflux
02-12-2013, 03:15 AM
That isn't an input, it's the frequency control. Use a small screw driver to adjust the speed of the flux...

Ahhh... Got it. Thanks for clearing that up.

DMC5180
02-17-2013, 04:46 PM
OK, Just suggestion here. You could mount a single RCA style JACK or a pigtail JACK in Parallel to the existing switch. Split the 2 wire conductor and connect to each side of the existing switch. Then simply get a length of speaker wire with an RCA PLUG attached and run the wire forward to the Console ON/OFF switch and attach with 3/16 spade receptacles. The center conductor of the RCA jack is (POS) the Outer body (NEG) from a current flow standpoint. In this case it really doesn't matter because the power source is the internal (9V battery). Using the RCA jack allows you to quickly unplug it for removal.

DMCflux
02-17-2013, 07:02 PM
OK, Just suggestion here. You could mount a single RCA style JACK or a pigtail JACK in Parallel to the existing switch. Split the 2 wire conductor and connect to each side of the existing switch. Then simply get a length of speaker wire with an RCA PLUG attached and run the wire forward to the Console ON/OFF switch and attach with 3/16 spade receptacles. The center conductor of the RCA jack is (POS) the Outer body (NEG) from a current flow standpoint. In this case it really doesn't matter because the power source is the internal (9V battery). Using the RCA jack allows you to quickly unplug it for removal.

This may be just what I'm looking for. I'm going to try this. Thank you

StainlessSteelDream
07-24-2013, 12:53 PM
Hey Guys,

Sorry to hijack this thread; (if I am)

I have one of the storage doors ... but it's a bit stiff to open and close, and this has lead to it pulling apart, the front door & 'glass' panel has pull free of the back electronics/flux panel. It's only held together by 4 brads, 1 per corner.

I was thinking of gluing the entire perimeter with black RTV .. or even normal white glue; hopefully there's no need for a bunch of venting or such.

Anyone else had this problem? Or have a suggestion?

Thanks

M