PDA

View Full Version : Fuel (another) "wont start" thread



DMC1983
02-16-2013, 10:52 AM
Being away for close to 7 months and leaving the car in the care of someone else, the lack of attention is catching up. This time, the car will not start. For some reason the fuel pump isnt running. I tried jumping the pins for the RPM relay, checked the inertia switch, and checked for continuity at the fuse block. None of which give me any signs of life. What would be my next best move?

rothsean
02-16-2013, 11:14 AM
I would check to see if there is electricity going to the fuel pump wire connection. If not, replace the fuel pump unit.

DMC1983
02-16-2013, 11:20 AM
I would check to see if there is electricity going to the fuel pump wire connection. If not, replace the fuel pump unit.

Well, the problem is: I'm not even getting voltage at the 87/30 terminals

DMC5180
02-16-2013, 12:09 PM
What's the condition of Fuse 7 ?

Power flow: Battery + >> Main Relay >> Fuse 7 >> Fuel pump Relay >> RPM Relay >> Fuel Pump >> Inertia switch >> Chassis Ground.

DMC1983
02-16-2013, 12:14 PM
What's the condition of Fuse 7 ?

Well, looking further into my problem I found that fuse 7 isn't even hooked up... It was bypassed. The PO cut the wires off the back because the fuse block melted and used a jumper fuse in place of it. The idiot used a LOT of electrical tape to cover up his crap splicing and Im in the middle of cutting it off right now

Bitsyncmaster
02-16-2013, 12:16 PM
Is your battery dead? Just turn on the headlights to test the battery.

DMC1983
02-16-2013, 12:22 PM
Is your battery dead? Just turn on the headlights to test the battery.

Just replaced it with a brand new Interstate MT-78 from work. Full 12 volts at the posts

Jonathan
02-16-2013, 12:23 PM
If your car is an automatic, it won't start unless the shifter is all the way up into park (or maybe neutral too, I don't remember for certain). Another easy thing to check anyway.

Bitsyncmaster
02-16-2013, 12:29 PM
Just replaced it with a brand new Interstate MT-78 from work. Full 12 volts at the posts

Just an FYI:

Testing voltage on the battery with no loads tells you nothing about battery condition. With the headlights on your loading about 15 amps.

DMC1983
02-16-2013, 12:31 PM
What's the condition of Fuse 7 ?

Power flow: Battery + >> Main Relay >> Fuse 7 >> Fuel pump Relay >> RPM Relay >> Fuel Pump >> Inertia switch >> Chassis Ground.

Fuel pump relay? Same thing as the Lambda Relay?

DMC5180
02-16-2013, 12:54 PM
Fuel pump relay? Same thing as the Lambda Relay?

Yes, My schematic has it listed as Main Fuel Relay (aka Lambda). Fuse 7 circuit Feeds power to the lambda relay then continues to the RPM relay via a second Brown wire Doubled into HOT terminal of the lambda relay socket.

This a perfect example where a simple (12V test light ) would be handy for finding power.

David T
02-16-2013, 12:57 PM
To get around all of the wiring just put power and ground on the fuel pump to get it running and see if the motor will start. Make sure you are checking for power on the correct relay, the RPM relay which is under the metal shelf. My guess is the #7 fuse is not wired in properly after bypassing the fuseblock. When checking for power in the Delorean you MUST always be sure you have a GOOD ground connection. When working in the fuse area the battery is about the best place.
David Teitelbaum

DMC1983
02-16-2013, 01:17 PM
Alright, so now I'm getting continuity and voltage at the rpm relay from source (fuse 7) to the input. That rules out the lambda relay and the fuse. Although, I get nothing from the purple/white to ground, no reading whatsoever whether it be open or infinite. I want to test the voltage at the pump now. What is the nearest ground at the pump?

DMC5180
02-16-2013, 01:25 PM
Alright, so now I'm getting continuity and voltage at the rpm relay from source (fuse 7) to the input. That rules out the lambda relay and the fuse. Although, I get nothing from the purple/white to ground, no reading whatsoever whether it be open or infinite. I want to test the voltage at the pump now. What is the nearest ground at the pump?

You must to JUMPER the RPM relay socket in order to get power to the FP for test purposes. Otherwise just reinstall the RPM relay and Crank the engine. The Relay must read RPM pulse singles in order to operate properly.

DMC1983
02-16-2013, 01:27 PM
You must to JUMPER the RPM relay socket in order to get power to the FP for test purposes. Otherwise just reinstall the RPM relay and Crank the engine. The Relay must read RPM pulse singles in order to operate properly.

Whoops, I meant continuity, not voltage. I want to check the ground side of the pump

DMC5180
02-16-2013, 01:41 PM
Whoops, I meant continuity, not voltage. I want to check the ground side of the pump

Have you confirmed 12V at any Location thus far? Ground continuity from the FP goes through the Inertia switch to Chassis ground. Disconnect the 2 wire plug at the FP pigtail harness Test the Black/Purple to ground (use one of the body mount bolts in the trunk)

DMC1983
02-16-2013, 01:59 PM
Have you confirmed 12V at any Location thus far? Ground continuity from the FP goes through the Inertia switch to Chassis ground. Disconnect the 2 wire plug at the FP pigtail harness Test the Black/Purple to ground (use one of the body mount bolts in the trunk)

I have a full 12 volts at the RPM relay from the source. With it jumpered, I get nothing at the pump.

DMC5180
02-16-2013, 02:12 PM
I have a full 12 volts at the RPM relay from the source. With it jumpered, I get nothing at the pump.

Just to confirm: (Key in Run position) You jumped the brown to Purple/white in the RPM socket? Did you check the 2 wire FP harness connector?

DMC1983
02-16-2013, 02:20 PM
Just confirm: (Key in Run position) You jumped the brown to Purple/white in the RPM socket? Did you check the 2 wire FP harness connector?

Key in run position. Yes, I jumped brown to purple/white and I did check both power at the RPM socket and at the Fuel Pump connector. Showed a full 12 at the RPM socket with nothing at the pump.

DMC5180
02-16-2013, 02:30 PM
Key in run position. Yes, I jumped brown to purple/white and I did check both power at the RPM socket and at the Fuel Pump connector. Showed a full 12 at the RPM socket with nothing at the pump.

Bummer: That should be one contiguous wire from RPM to the FP connector, however there could be another connector buried in the underbody You have to drop the Washer fluid tank to get at it.

DMC1983
02-16-2013, 02:37 PM
Bummer: That should be one contiguous wire from RPM to the FP connector, however there could be another connector buried in the underbody You have to drop the Washer fluid tank to get at it.

Thats what I was afraid of. Washer fixing screws are rusted out and will require drilling. I still need to test the continuity of the wire going to the pump though. I need to be sure it's a break or a short before I delve any further into it. It still baffles me that things could go this terribly wrong when the car is sitting

DMC5180
02-16-2013, 02:41 PM
http://store.delorean.com/c-349-3-7-2-front-harness.aspx The bottom image is the front harness that goes to Item 6 FP harness. You will have to drop the Washer fluid reservoir ,which can be a (PITA) in order to get at the Main to Front harness connector.

Hopefully Mice did not get at the area but anything is possible.

DMC1983
02-16-2013, 02:44 PM
Bummer: That should be one contiguous wire from RPM to the FP connector, however there could be another connector buried in the underbody You have to drop the Washer fluid tank to get at it.


http://store.delorean.com/c-349-3-7-2-front-harness.aspx The bottom image is the front harness that goes to Item 6 FP harness. You will have to drop the Washer fluid reservoir ,which can be a (PITA) in order to get at the Main to Front harness connector.

What else does the harness power? based on the photo it's hard to tell what all connections are there. Horns? Radiator fans? Im not sure

Ron
02-16-2013, 02:54 PM
I need to be sure it's a break or a short before I delve any further into it. It still baffles me that things could go this terribly wrong when the car is sitting

If you put 12V on pin 87 (via the Brown wire) of the RPM relay and there is no power on the White/Purple wire at the Fuel Pump plug, you HAVE proved there is a break in the White/Purple wire. If you bring 12V from somewhere else to that point, the pump should run.


Hopefully Mice did not get at the area but anything is possible.
I'm betting on the mouse!

DMC5180
02-16-2013, 02:58 PM
What else does the harness power? based on the photo it's hard to tell what all connections are there. Horns? Radiator fans? Im not sure


Yup. Horns, Cooling Fans, Fuel Pump, Tank Sender and Brake Fluid level switch. It may just be a case of poor connection of Purple/white wire terminals in that Connector.

DMC1983
02-16-2013, 03:06 PM
Yup. Horns, Cooling Fans, Fuel Pump, Tank Sender and Brake Fluid level switch. It may just be a case of poor connection of Purple/white wire terminals in that Connector.

Well, the horns work if that makes anything hah! Well, Ill go ahead and rip out the washer bottle.

DMC5180
02-16-2013, 03:43 PM
Well, the horns work if that makes anything hah! Well, Ill go ahead and rip out the washer bottle.

Surface rusted Bolt heads don't always mean they are rusted in the Riv-nuts. If you have a cordless drill with an Hex to 1/4 drive adapter. You may be able to rattle the fasteners ( start with a low Clutch setting 5-6) increase as necessary. The slipping clutch causes vibration into the rotational torque. (Poor mans impact wrench) If the they vibrate enough they might come loose. If the they are frozen, it could spin the riv-nut an or snap the M5 bolts. The worst case being you still end up drilling the heads off the bolts anyway. I've also had great success using a LOW torque cordless Impact wrench.

DMC1983
02-16-2013, 03:51 PM
I ruled out the front harness, so all that's left is what's between the RPM relay and the connector. Looks like I got to tear the car apart now

DMC5180
02-16-2013, 03:55 PM
I ruled out the front harness, so all that's left is what's between the RPM relay and the connector. Looks like I got to tear the car apart now

How did you rule out the front harness? Did you access the buried connector?

DMC1983
02-16-2013, 03:56 PM
How did you rule out the front harness? Did you access the buried connector?

Yep, Tested the connection with the fuel pump connected. Source to ground. Even checked the inertia switch connections.

DMC5180
02-16-2013, 04:09 PM
Yep, Tested the connection with the fuel pump connected. Source to ground. Even checked the inertia switch connections.

Now I'm confused. You were able to drop the Washer Fluid Reservoir in order to gain access to the connectors?

DMC1983
02-16-2013, 04:35 PM
Now I'm confused. You were able to drop the Washer Fluid Reservoir in order to gain access to the connectors?

Yeah... details aside, I was able to get the screws out of the base and the washer bottle came out. no hassle

Silverbullet
02-16-2013, 04:42 PM
So.....

Why not get some wire, connect to a 12 volt source, hot wire the pump to test it... make sure it has the ground connected... See if it starts the car...This way you can know if the pump is good or bad... Then all you have to do is chase the wires backwards to find the problem...

Craig

Bitsyncmaster
02-16-2013, 04:44 PM
One of the more common fuel pump connection problems is the 2 pin connector right near the pump. You should be able to pull the pump wires enough to see that connector.

For these connections tests, I have a long ground wire I use with my meter. So I can reference each voltage reading back to the common neg battery terminal (or the group of black wires in the relay compartment). You can also use that long meter wire to read voltage drops over each circuit to find poor connections.

You should get voltage at the pump with the Large brown wire jumpered to the large white/purple wire at the RPM relay. You don't need the key on.

DMC5180
02-16-2013, 04:51 PM
Yeah... details aside, I was able to get the screws out of the base and the washer bottle came out. no hassle

Ok, thanks for filling in the blank. If you a have 12V test probe (piercing tip) You can check spots along the harness run. In the Upper Left corner of the Drivers footwell you can see were the main harness goes into the underbody. See if you can find the purple/white wire and probe it for 12V. You'll need to peel back some of the harness wrap. It should be one continuous wire from the RPM relay socket to the front harness connection.

DMC5180
02-16-2013, 04:56 PM
One of the more common fuel pump connection problems is the 2 pin connector right near the pump. You should be able to pull the pump wires enough to see that connector.

For these connections tests, I have a long ground wire I use with my meter. So I can reference each voltage reading back to the common neg battery terminal (or the group of black wires in the relay compartment). You can also use that long meter wire to read voltage drops over each circuit to find poor connections.

You should get voltage at the pump with the Large brown wire jumpered to the large white/purple wire at the RPM relay. You don't need the key on.

He's already confirmed the front harness to ground via the FP. ( yeah I forgot you don't need the key ON to jumper the relay)

OverlandMan
02-17-2013, 01:44 PM
Just read through this entire thread. I can't really contribute anything past what's already been said but I did want to recommend one of these: http://www.powerprobe.com/pp1.php.

I've been using one for 10+ years and they really save lots of time when testing circuits on 12V DC. Its a good investment, especially for these cars.

DMC1983
02-18-2013, 08:50 AM
Just read through this entire thread. I can't really contribute anything past what's already been said but I did want to recommend one of these: http://www.powerprobe.com/pp1.php.

I've been using one for 10+ years and they really save lots of time when testing circuits on 12V DC. Its a good investment, especially for these cars.

Wow, looks like a real winner! I'll have to pick one of these boys up. It'll be at least another week before I can get back down to try and find my problem. My best bet is probably going to be under the center console.

David T
02-18-2013, 08:17 PM
Not all of these types of probes can power high draw items like a fan or a fuel pump. Make sure before you buy it that it can handle the amount of power you require. This one says 6-10 ma which isn't much. They take great pains to mention how much individual components can handle but what you really need to know is what the whole system can handle.
David Teitelbaum

OverlandMan
02-19-2013, 10:51 AM
Not all of these types of probes can power high draw items like a fan or a fuel pump. Make sure before you buy it that it can handle the amount of power you require. This one says 6-10 ma which isn't much. They take great pains to mention how much individual components can handle but what you really need to know is what the whole system can handle.
David Teitelbaum

Correct. Mine has a circuit breaker on the side you can reset easily. Typically they'll run the target equipment long enough to test function. I powered my cooling fans (1 at a time) for 3-4 seconds when doing some testing last year and didn't trip the breaker. I think that 6-10 ma might be a misprint. Seems like the breaker on mine is 5 amps or thereabouts.

DMC1983
03-15-2013, 02:42 PM
Resurrecting this old one.

Worked on the car today and found that the ground side of the circuit is bad. The inertia switch is in the closed position but still has a bad ground. My question is: where is the physical ground on the inertia switch?

David T
03-15-2013, 03:29 PM
Before that I would check for ground at the inertia switch and check the switch itself. Make sure it has a splotch of white paint on it and it is mounted on the side of the footwell, NOT the Lambda counter as per recall. The original switches are notorious for failing. Also, the inertia switch has TWO circuits running through it. It is supposed to shut the fuel pump off AND unlock the doors in an accident serious enough to trip it. It is possible somehow the circuits got mixed up. I have seen on some cars the molded plastic plug was missing and the wires were individually attached to the switch (and not correctly). You could always run a temporary wire to ground for testing purposes.
David Teitelbaum

DeLorean03
03-15-2013, 03:30 PM
While I do not know the physical location of the ground, my suggestion would be run a ground wire from the inertia switch to the frame. That will fix that.

DMC1983
03-15-2013, 04:31 PM
While I do not know the physical location of the ground, my suggestion would be run a ground wire from the inertia switch to the frame. That will fix that.

I have the circuit all the way to the inertia switch testing good. I have yet to check the inertia switch itself.

DMC1983
03-22-2013, 09:26 AM
Update: After much frustration testing circuits and checking grounds, my problem all along was the fuel pump connections itself. PO had done a crap job installing spaded leads (with a ton of electrical tape) on the pump. They were corroded... so I replaced the leads and installed new wiring (the aircraft mechanic way:wink:) and boom! Im running again!

I appreciate everyone's help and will do my best to return the favor in the future