PDA

View Full Version : Frame & Body Cabin air extraction q.



Rich
02-17-2013, 09:46 PM
This subject may have been touched on recently in another thread.

A very minor question here about how D's work, having to do with the air flow in the passenger compartment. Am not looking to change it but am curious to know whether there are any deliberate extraction vents or apertures that do anything.

We can see these external blades, which indeed have narrow slots that might let some air out. Does air get expelled there or anywhere else from the cabin - other than by rolling down the windows?

16620

Inside the cabin one can see the speaker perforations in the interior rear side panels and there are slots in the rear panel that carries the rear interior light. Having never looked behind these external blades I can't tell if they do anything or not.

Shep
02-17-2013, 09:56 PM
In the early VIN's, the holes for the speaker vents let air out through a hole in the underbody underneath the rear quarterpanel. Here's a picture:

http://vin559.com/images/events/dpi/2012-12-22/resized/dpirollingchassis06_640.jpg (http://vin559.com/images/events/dpi/2012-12-22/dpirollingchassis06.jpg)

It's directly to the left of the top of the wheel well and below the side of the rear windshield in the picture.

jawn101
02-17-2013, 10:14 PM
Shep is correct Rich. But those vents are really cosmetic, ultimately. Even with the holes in the tub on early cars there were so many obstructions that I don't think you could consider them 'air extraction', other than maybe at a very slow rate. Canon and anecdote tells us that they were originally intended to equalize pressure when the doors were closed, but eventually just proved to be a haven for water and rodents while actually doing nothing for air pressure :)

Jonathan
02-18-2013, 11:51 AM
Neat question, Rich. You got me thinking.

Are you asking because of the idea of "you can't blow air into the car if there isn't a place for air to leave the car?"

I couldn't think of any specific air exits either. We all know our cars are not usually super water/air tight, but that isn't the design necessarily, it might be more to do with old seals in various places. Like you said, air leaves when the windows roll down, or out one of the grommets or seals that isn't tight.

I googled the question and there are a few other car forums who have asked the same thing. One guy mentioned why their cars have plastic sheeting inside the doors. Hmmm, my D had that same plastic sheeting at one point too, but there is likely very little of it left now. It was likely also part of the air seal.

I don't know what the internals look like on the HVAC system and blower, but I wonder if when it is blowing in say at your feet, it is also letting air return through the vents not in use, like up at the windshield or centre vents? I don't know if it works that way or not. Our cars don't have the recirc versus new air button like most new cars do now.

Obviously we aren't going to be pressurizing our cars, so it is going somewhere. If new air comes in at the lower portion of the windshield, could it also leave that way?

jawn101
02-18-2013, 12:08 PM
The plastic sheets inside the doors are actually 'moisture barriers', which help keep any water that may get into the door via the windows from getting into the cabin. They basically ensure that the water is redirected to the drain holes in the door, rather than soaking into the door trim/carpet. Almost every car has them, but they are especially important in our cars since most car doors never find themselves lifting vertically :)

DMC5180
02-18-2013, 12:33 PM
Neat question, Rich. You got me thinking.

Are you asking because of the idea of "you can't blow air into the car if there isn't a place for air to leave the car?"

I couldn't think of any specific air exits either. We all know our cars are not usually super water/air tight, but that isn't the design necessarily, it might be more to do with old seals in various places. Like you said, air leaves when the windows roll down, or out one of the grommets or seals that isn't tight.

I googled the question and there are a few other car forums who have asked the same thing. One guy mentioned why their cars have plastic sheeting inside the doors. Hmmm, my D had that same plastic sheeting at one point too, but there is likely very little of it left now. It was likely also part of the air seal.

I don't know what the internals look like on the HVAC system and blower, but I wonder if when it is blowing in say at your feet, it is also letting air return through the vents not in use, like up at the windshield or centre vents? I don't know if it works that way or not. Our cars don't have the recirc versus new air button like most new cars do now.

Obviously we aren't going to be pressurizing our cars, so it is going somewhere. If new air comes in at the lower portion of the windshield, could it also leave that way?

Our cars do have a RECIRC but only on MAX A/C. All Air coming into the HVAC system is through the Blower Fan Intake at the base of the windshield. Air does not return thru unused vents as in defrost, doors or floor vents as long as the pressure inside the HVAC housing is greater than it's surrounding pressure. It leaks out of every orifice that is not sealed all that well. There are enough leak points in the car that it probably doesn't need those vents. But it is pretty cool that they were intended to be functional and not just decorative. If you have the blower fan on 4 then crack the window and don't feel a flow increase from the vent then you know there is plenty of leakage other places. I had a couple cars with pop-up sunroofs that when open made a noticeable difference in from the vent ducts at Hwy speed.

I have uncle who had a Mid 70's Caddy Sedan Deville. It was so tight the last person to close the door getting in would have to crack the window to shut it fully. Otherwise it would only catch the first Click of the latch. You could also feel the pressure change in your ear.

David T
02-18-2013, 12:53 PM
The Delorean does not have a designed air path. Probably an oversight or just an economic compromise to be finalized in later versions. There is enough leakage and it is a small enough compartment that it isn't all that important. Probably why the Vent function isn't very effective. Hardly used anyway. I usually have it on Max or A/C and that seems to work well enough.
David Teitelbaum

Bitsyncmaster
02-18-2013, 05:43 PM
On my car if the AC is not on max and the windows are closed, I get an air whistle on fan speed 3 or 4. Crack the window and the noise goes away.

DMCVegas
02-19-2013, 11:25 AM
Who wants to play Name that part?

http://store.delorean.com/images/Product/medium/108107.JPG

SS Spoiler
02-19-2013, 11:27 AM
Vent pipe to battery box

jawn101
02-19-2013, 11:43 AM
Who wants to play Name that part?

http://store.delorean.com/images/Product/medium/108107.JPG

What, the foam strip around your battery box door isn't airtight??? :lol:

DMCVegas
02-19-2013, 12:18 PM
What, the foam strip around your battery box door isn't airtight??? :lol:

Batteries produce hydrogen gas which of course is very flamable. There is even a warning label on your battery cover (part 106093) that tells you of this. The idea is that whenever you have the blower motor on, the positive air pressure will force any hydrogen gas in the battery compartment out through that vent tube. So there are intended cabin exhaust points on the car. If you've got whistling at higher pressures, this tube might be clogged.

Years before I thought about descreetly mounting superbright amber LEDs in my vents to act as turn signals. Don't know if I'll ever do that, or especially now if I could reinstate DMC's cabin exhaust design. I would however install flaps to prevent water and dirt from working it's way back into the system, as well as to reduce road noise. I might just use a door jamb vent from another car to accomplish that.

David T
02-19-2013, 06:33 PM
I really doubt how effective that vent tube is for the battery. Maybe the spinning wheel creates enough of a vortex to make air come out, I don't know. We all know how well you get fuel fumes into the cabin if you have a fuel leak in the front, that tells me the cabin is under negative pressure and it draws the fumes in. DMC did not put a lot of thought into cabin ventilation.
David Teitelbaum

DMCVegas
02-19-2013, 08:19 PM
I really doubt how effective that vent tube is for the battery. Maybe the spinning wheel creates enough of a vortex to make air come out, I don't know. We all know how well you get fuel fumes into the cabin if you have a fuel leak in the front, that tells me the cabin is under negative pressure and it draws the fumes in. DMC did not put a lot of thought into cabin ventilation.
David Teitelbaum

No, not at all. The cabin is under positive pressure that comes from the blower motor. The problem with the gasoline vapors are when they escape from the tank, they get sucked in by the drain tube at the bottom of the air plenum, right above the gas tank. Most modern vehicle now days that have either the plenum or air conditioning drain directly into the engine compartment rather than under the car have a rubber check valve on the end of the tubes like this:

http://i25.tinypic.com/2mq6bur.jpg

Speaking of gas fumes, it's something that I've dealt with on my own car and was caused by a defective charcoal canister that wasn't purging the excess gas fumes when the engine was running. Thanks to the coolant pipes next to the fuel tank heating the gasoline up, I could see the whole tank was swollen and was bubbling gasoline out of the welds on my Tankzilla (not to mention collapsing the inlet hose and causing the fuel tank to buzz). Long story short, after I swapped the canister the problem went away and never returned. Been through the same thing with a Jaguar and even company vehicles. You don't notice it usually on vehicles with the fuel cell in the back unless you're stopped for a period of time, but it's actually a problem with ALL cars and is the reason that California incorporated testing of the canister on some vehicles into their emissions tests. Usually too it's caused by topping-off while filling up. Otherwise it's just age related.

David T
02-19-2013, 11:19 PM
I don't know about that. I have seen where even if you are not running the fan, if you have any fuel leakage at all, you very quickly get a smell of fumes in the cabin. I would like to think the fan would draw in outside air and pressurize the cabin but I don't think that is what happens. I am going to have to get my smoke machine out and do some tests. It may be difficult to do that while driving though!
Speaking of a malfunctioning vapor system, I have found on several cars the large drain tube coming out of the bottom of the center of the canister was plugged up with insect debris preventing the canister form operating properly. Other sources include:
deteriorated cover boot or fuel pump boot
incorrectly assembled fuel components
loose ring on the fuel sender/missing gasket

Maybe what happens is the fan does actually pressurize the cabin but it is drawing in air from around the gas tank so it actually pulls in the fumes. I am guessing but I don't think it will pull air in from the condensate drain.\

A small experiment is in order.
David Teitelbaum

DMCMW Dave
02-20-2013, 12:03 AM
Maybe what happens is the fan does actually pressurize the cabin but it is drawing in air from around the gas tank so it actually pulls in the fumes. I am guessing but I don't think it will pull air in from the condensate drain.\

A small experiment is in order.
David Teitelbaum

I believe it pulls it in through the windshield drain that is strategically located just above the fuel pump, and is a direct connection to the blower intake.

DMCVegas
02-20-2013, 01:23 AM
Bingo! You've both got it. I'm not talking about the A/C Evaporator nor the condensation drain tube. That goes between the underbody and chassis and sits lower that the gas tank.

The air plenum is not a "part" in the sense that its something you can replace. It's formed during the construction of a vehicle's firewall/bulkhead, and it's whole purpose is to separate liquid so that it is not sucked into the car's ventilation system.

It sits right below the windshield. It's not a duct because its not sealed so it can treat the air. Fresh air goes down past the grate, and then does an upward turn behind a splash shield so liquid can't be sprayed directly into the system. All of the liquid collects on the bottom of the plenum and the drains out. In the DeLorean, that drain dumps right above the gas tank.

As I said, liquid drains out of the bottom because its too heavy to be sucked into the ventilation system. BUT when you have fuel vapors that escape from the gas tank (exacerbated by the water lines heating the whole tank up), they're light enough to be sucked into the car as they rise and get pulled up through that drain. Again, modern cars that have drains that dump into the engine compartment usually have a rubber check valve like the one on that picture that will snap shut from the negative pressure of the intake, but will open when the weight of water pushes down on it.

To test things, turn the blower on and hold your fingers below the battery vent tube. You should feel a slight breeze.

Testing the carbon canister to check for gasoline smells or noisy fuel pumps is easy. First warm the car up to temperature and to the point where the smell/sound begin to become apparent. Then pop the gas cap and shove a pencil or screwdriver into the inlet restrictive to hold the door open. That should quiet the pump.

Next warm the car up again to where the problem returns. Disconnect the trigger hose to the canister and connect a hand pump vacuum in its place and start the hot engine. Keep pumping and you'll eventually pop the diaphragm inside. When that happens (thanks to the vacuum leak you caused by leaving that hose off, the engine will rev as the vapor rushes in from the gas tank and feeds the engine. Now you know that you've got a defective vapor canister.

Farrar
02-25-2013, 05:06 PM
In the early VIN's, the holes for the speaker vents let air out through a hole in the underbody underneath the rear quarterpanel.

Thanks for posting that. I am about to close those two holes on my car and was wondering if they were (or had been, at some point) connected with the tiny side vents. Now I know where the water in my car came from when it was blustery rainy outside. :)

Shep
02-25-2013, 10:13 PM
Thanks for posting that. I am about to close those two holes on my car and was wondering if they were (or had been, at some point) connected with the tiny side vents. Now I know where the water in my car came from when it was blustery rainy outside. :)You're welcome! Now you know why I was confused in the thread you posted addressing it from the inside :hihi2:

On a side note, we decided to plug those holes on mine rather than patch them, so they would still be there, but sealed. Based on everywhere else they used this plug when they had unneeded 3" holes, I believe part number 106678 [link (https://store.delorean.com/p-8705-cover-clutch-resvr.aspx)], the cover for the clutch reservoir (which, strangely, is also on automatics), can seal it up. As a quick test, you can grab the one right next to your gas cap and see if that fits. It's the same part, and if it fits, you should be able to order two more of them and seal it up securely and easily. You might need a screwdriver to get it out, the handlebar doesn't always work since it's rubber and all.

Farrar
02-26-2013, 09:49 AM
On a side note, we decided to plug those holes on mine rather than patch them, so they would still be there, but sealed.

FWIW, I plan on using some aluminum flashing cut to fit, riveted to the fiberglass and sealed with RTV. Dave S. suggested this method as it has worked for him, and he is like my DeLorean Guru. :yoda: