Log in

View Full Version : General Need Suggestions: Trouble Shooting



darylfelsberg
02-21-2013, 06:45 PM
I am sure this has been done 100's of time's by you guys and I apologize. However, we need some trouble shooting ideas.

Bought a sitting complete DMC 12, aging owner just left it. Typical 10-20 year non running sitter. Here is what we did: bought Hervey's fuel pump, cleaned tank, replaced accumulator, fuel filter, had Hervey recon the and check the fuel distributor, air flow meter, all injectors. He checked the pressure regulator, cold start valve, and frequency valve and sent it back, and we installed it over the weekend.

It turns over, putts a little like it's trying to run. We pulled a few of the plugs and they are wet.

What do you check first? Second? Third? Etc.
Thanks, in advance.

Spittybug
02-21-2013, 07:06 PM
Fuel, Air, Spark. :werd:

Fuel - yup, plugs are wet
Air - confirm that your throttle blades are opening/closing with your foot pedal. Have you tried starting holding your foot down on the gas (old carb trick to clear floods?) This would help diagnose if you have a bad arm up regulator.
Spark - Most likely. Easy to check. Pull a plug wire off and let it arc to the block (<1 inch) as you crank. Wear gloves. Check all. How do they look? Open distributor cap, is it worn?


Report back.

Jonathan
02-21-2013, 07:21 PM
Spark - Most likely. Easy to check. Pull a plug wire off and let it arc to the block (<1 inch) as you crank. Wear gloves. Check all. How do they look? Open distributor cap, is it worn?

+1 on the spark avenue.

Ensure all spark plug wires are going from the right spot on the distributor to the correct number/sequenced cylinder.

Double check that the "hot start plug swap" connectors are where they should be (i.e. not reversed the way they would be if you were trying the hot start trick).

sdg3205
02-21-2013, 07:44 PM
What Jonathan said. It is VERY easy to put the plug wires in the wrong place. Double and triple check and trace them right to the distributor

Dangermouse
02-21-2013, 08:21 PM
Don't forget the one to the coil.

If the wires/leads are in fact 20 years old I would go ahead and replace them.

darylfelsberg
02-21-2013, 09:11 PM
Failed to mention that we replaced the coil, Dist cap and rotor, spark plug lines, plugs, and vacuum hoses.

Jonathan
02-21-2013, 09:29 PM
Failed to mention that we replaced the coil, Dist cap and rotor, spark plug lines, plugs, and vacuum hoses.

Ok, dollars to donuts says one or more of the plug wires is in the wrong spot mistakenly. If I'm wrong I owe you a maple dip :)

EDIT: or the distributor cap is installed 180 degrees off.

EDIT2: double check your vacuum hose routing as well.

Dangermouse
02-21-2013, 10:10 PM
What J said :)

David T
02-22-2013, 12:04 AM
Verify that you are getting a spark on a spark plug. If you can do that then you have to check your firing order. Do you know how the cylinders are numbered? The cap should have the cylinder numbers on it, make sure the wires are going to the correct cylinder. The cap has a notch so it is difficult to put it on wrong. Make sure the rotor is indexed correctly and fully seated on the shaft. If the ignition system is OK you can always try getting it to run a little on some Ether. Then you would know it is a fuel problem. Make sure the distributor is still plugged in and you didn't knock any other wires loose.
David Teitelbaum

Kenny_Z
02-22-2013, 12:23 AM
EDIT: or the distributor cap is installed 180 degrees off.


I did this. It is extremely easy to do and it had the exact same symptoms that you described. I kicked myself for days over a very simple mistake that is a complete pain in the ass to fix.

Ron
02-22-2013, 09:14 AM
Maybe check that the exhaust system hasn't been converted into a mouse mini storage...

David T
02-22-2013, 12:28 PM
Even if the exhaust was completely blocked the motor would still start, it would die if you tried to rev it up. If it is not starting either you are not getting air, fuel, or spark, or not at the right time. While pulling the plugs I would do a compression check just to know the mechanicals are OK. Since they have never seen this motor running you really do not know what is good, if anything. It is also possible they messed up a fuel hose and something is not connected correctly. We have seen on this list where someone switched the feed and return lines at the fuel pump.
David Teitelbaum

darylfelsberg
02-22-2013, 07:23 PM
Ok, we checked the Cap and wires and they are all correct. My mechanic took the plugs out dried them, checked for an arc, and we had electric. We are assuming it's a mixture or air issue, and are waiting Hervey to call us to walk through it. I'll have him check the feed and return line to see if they are backwards. We are having a hard time finding an easy to see diagram of the fuel line routing. I may also add, when we crank it over, all the cabin lights go dim....like out. Nothing except the door indicator light is on.

Jonathan
02-22-2013, 07:42 PM
Do you have concrete proof the battery is new (at least less than 5 years old)? If it has been sitting in the car for the same length of time you mentioned the car itself sat, you need to buy a new one.

Dangermouse
02-22-2013, 07:46 PM
Don't mean to second guess your mechanic but it is very easy to get the dizzy cap reversed. There is a shallow notch that is supposed to prevent this, but I too managed it and had the same symptoms that you are describing.

You can't tell by looking at it installed. You have to take it off, which is a little fiddley

Ron
02-22-2013, 08:29 PM
We are having a hard time finding an easy to see diagram of the fuel line routing.

Here ya go-
16763

darylfelsberg
02-22-2013, 10:10 PM
Battery was replaced in December.

THanks for the Diagram! That'll help a lot.

As far as the Cap, we may have to pull the manifold if nothing else and put it back on.

David T
02-23-2013, 07:07 PM
You don't have to pull the manifold, by undoing the mixture unit you can move it enough to get access to the distributor. Now that you have confirmed spark, you could try a squirt of Ether and see what happens. If you get it to run you have a fuel problem and if it won't run you have a timing problem withe the spark. Pull fuse #7 while testing with Ether and use it sparingly.
David Teitelbaum

darylfelsberg
02-26-2013, 01:33 AM
Damn distributor cap. Reset it; started up for the first time in 15 years. Thanks for the help. I'll get the next calamity ready for you and ask for direction. I appreciate everyones input.

Dangermouse
02-26-2013, 10:08 AM
I love it when a plan comes together

http://media.tumblr.com/tumblr_m91ntyGkIM1qel770.jpg

lazabby
02-26-2013, 03:00 PM
Where in Texas are you? Dallas area?

darylfelsberg
02-27-2013, 01:30 AM
I am about two hours east of Dallas in Paris, Texas.

kings1527
02-27-2013, 02:07 AM
Damn distributor cap. Reset it; started up for the first time in 15 years. Thanks for the help. I'll get the next calamity ready for you and ask for direction. I appreciate everyones input.

I saw this late. I did the EXACT same thing a couple months ago. It is amazingly easy to do and a bit of a pain to correct. It's funny how if you're not aware of how the distributor cap goes on, you have a 50/50 shot of accidentally getting it right. But it seems like us people doing it will choose the wrong way 100% of the time. :banghead::tongue: