Log in

View Full Version : Transmission 5-Speed Clutch Problem.



refugeefromcalif
02-23-2013, 07:49 PM
I've been having a clutch problem with 6599 for the past 2 months. (My starting problem(s) will end up in another thread)...
When I first start driving, the clutch pedal has about an inch? of travel before I get the resistance that tells me that the clutch is being engaged.
In Stop and Go traffic situations, the pedal travel, (before I get the clutch resistance), tends to get Lower towards the floor ending up making me feel the gears to get into first gear from a stop.
Pumping the clutch doesn't make any difference.
Fluid level is OK. I haven't tried bleeding the clutch reservoir yet. It doesn't feel like an air problem.

I called Tony at DMCF 2 weeks ago about this, (I have a 12 month/12,000 mile warranty with them), and was told that they would take care of it when I got the car down to them.
He said that it sounded like an Easy Fix but I didn't ask him what I could do to fix it myself. (I was thinking Warranty on the car)...
The fact is, It's a 1,400 mile+ round trip and, it would cost me a total of 4 days+ to get the clutch back in order. I'd rather fix it at home...
I've had a few vehicles with hydraulic clutches but, I've Never had a problem like this before.?

Any ideas on what I can check? Anybody have anything similar?

I know that I'll have explain this further after I hear from you guys.

George

DMCMW Dave
02-23-2013, 08:08 PM
Do you have the braided stainless clutch line? If so, and nothing is really leaking (look inside the car next to the steering column where you can see the master cylinder AND at the back of the car just forward of where the frame goes under the engine), then all it can be is air in the system.


I've been having a clutch problem with 6599 for the past 2 months. (My starting problem(s) will end up in another thread)...
When I first start driving, the clutch pedal has about an inch? of travel before I get the resistance that tells me that the clutch is being engaged.
In Stop and Go traffic situations, the pedal travel, (before I get the clutch resistance), tends to get Lower towards the floor ending up making me feel the gears to get into first gear from a stop.
Pumping the clutch doesn't make any difference.
Fluid level is OK. I haven't tried bleeding the clutch reservoir yet. It doesn't feel like an air problem.

I called Tony at DMCF 2 weeks ago about this, (I have a 12 month/12,000 mile warranty with them), and was told that they would take care of it when I got the car down to them.
He said that it sounded like an Easy Fix but I didn't ask him what I could do to fix it myself. (I was thinking Warranty on the car)...
The fact is, It's a 1,400 mile+ round trip and, it would cost me a total of 4 days+ to get the clutch back in order. I'd rather fix it at home...
I've had a few vehicles with hydraulic clutches but, I've Never had a problem like this before.?

Any ideas on what I can check? Anybody have anything similar?

I know that I'll have explain this further after I hear from you guys.

George

refugeefromcalif
02-23-2013, 08:32 PM
Dave, Yes I have the braided clutch line. That was the first thing that Tony looked up on the work order that was done to my car before it went up for sale.
Thanks for the reply.

I'll do a bleed on the system and post my results.

George

David T
02-24-2013, 01:08 PM
It *could* be a defective clutch master cylinder. I recently had one where the seal to block off the reservoir leaked and if you held the pedal down the clutch would slowly engage. My plan would be to replace the clutch master and rebleed the system and see if that solved the problem.
David Teitelbaum

DMCMW Dave
02-24-2013, 01:54 PM
It *could* be a defective clutch master cylinder. I recently had one where the seal to block off the reservoir leaked and if you held the pedal down the clutch would slowly engage. My plan would be to replace the clutch master and rebleed the system and see if that solved the problem.
David Teitelbaum

I agree - there is no way on earth that the slave can leak without something ending up on the ground, but it is possible for the master to leak internally. Not very common, but possible. That would also lead to a situation where you don't lose any fluid.

refugeefromcalif
02-24-2013, 06:35 PM
It *could* be a defective clutch master cylinder. I recently had one where the seal to block off the reservoir leaked and if you held the pedal down the clutch would slowly engage. My plan would be to replace the clutch master and rebleed the system and see if that solved the problem.
David Teitelbaum


I agree - there is no way on earth that the slave can leak without something ending up on the ground, but it is possible for the master to leak internally. Not very common, but possible. That would also lead to a situation where you don't lose any fluid.

Thanks again for the help!

Would either of these problems Correct themselves by just by driving down the road for a few miles? That's what happens with mine. :confused:
I have sat at a red light in first gear, (Clutch engaged), for as long as 5 minutes and not had the clutch Dis-engage? making the car want to Creep forward.
The issue is, The more I use the clutch pedal, (in a short span of time), the More travel it takes to actually Engage the clutch. But when I'm cruising around for a bit, The pedal travel, (When it engages the clutch), goes back to Normal?

I guess this is one of those things that harder to write about, then talk to person about.
If I can figure it out, (and it's a Simple fix that won't void my warranty), I'll do it but, if not, I foresee a trip back to DMC Florida for them to fix it...

George

Tillsy
01-04-2014, 08:16 AM
I agree - there is no way on earth that the slave can leak without something ending up on the ground, but it is possible for the master to leak internally. Not very common, but possible. That would also lead to a situation where you don't lose any fluid.

Alrighty here's a big WTF...

1. Installed brand new master cylinder, slave cylinder, and stainless braided hose 1.5 years ago. Bled and worked perfectly.

2. Re-bled a few months later. No worries.

3. 1.5 years later I've now installed the, sorry to say, SpecialT clutch bleeder. Tried to bleed but noticed the clutch pedal would push freely 50% into the master cylinder before anything happened. Whilst trying to bleed that out noticed the SpecialT clutch bleeder was starting to leak at one of its joins, so threw it in the bin and reinstalled the original bleed nipple.

4. Continued bleeding still has the same problem - there is 50% free play in the pedal/master cylinder before the slave starts to engage. As in a mouse could push the pedal, there's nothing to it.

So ultimately the self-bleeder is now irrelevant, it was only there less than an hour and now gone, and no pressure bleeder involved or anything just the old fashioned pump and release.

I'm getting plenty of fluid out when I bleed, and no more air, so why the devil does the pedal and master cylinder have 50% play? I'm not convinced it is an air-pocket as there is NO resistance for that 50% at all. Have I co-incidentally had a failure of the master? Have had to call it a night for now as I'm very baffled what is going on here...

Tillsy
01-04-2014, 09:17 AM
4. Continued bleeding still has the same problem - there is 50% free play in the pedal/master cylinder before the slave starts to engage. As in a mouse could push the pedal, there's nothing to it.

And now there is a 5:

5. Have left it for an hour now and gone back to find only 10% free play...?!?

Rich
01-04-2014, 02:01 PM
...
3. 1.5 years later I've now installed the, sorry to say, SpecialT clutch bleeder. Tried to bleed but noticed the clutch pedal would push freely 50% into the master cylinder before anything happened. Whilst trying to bleed that out noticed the SpecialT clutch bleeder was starting to leak at one of its joins, so threw it in the bin and reinstalled the original bleed nipple.

Requesting more info -
When did the "50% free play" symptom first appear? Only after you attempted bleeding or was it happening during normal driving before any work?

And are you using correct bleeding technique? You have bled a clutch before so you know to close the bleed nipple after every pedal-press, before releasing pedal.

DMC5180
01-04-2014, 02:11 PM
Did you check to see if the Clutch master Piston was returning completely when let up on the pedal. Remember the pedal arm has its own return spring. If the piston isn't returning completely it could give you that No resistance feeling. Now that you've Got 10% free play That's about right. I always use 1" or (25-30 MM) as a general rule for free play in clutch pedal.

David T
01-04-2014, 02:49 PM
Did you check to see if the Clutch master Piston was returning completely when let up on the pedal. Remember the pedal arm has its own return spring. If the piston isn't returning completely it could give you that No resistance feeling. Now that you've Got 10% free play That's about right. I always use 1" or (25-30 MM) as a general rule for free play in clutch pedal.

It is possible to get a bubble of air "stuck" in the hose between the reservoir and the master cylinder. Especially if the hose is on the long side and makes a couple of bends. Tap and shake the hose to dislodge any air bubbles. If the hose looks like it is sweating it should be replaced. To bleed the system properly you need a flow to flush any air out, not just a trickle. If the fluid is not clear flush it good and then do the brakes.

Tillsy
01-04-2014, 05:06 PM
When did the "50% free play" symptom first appear? Only after you attempted bleeding or was it happening during normal driving before any work?
It appeared during the bleeding process.


And are you using correct bleeding technique? You have bled a clutch before so you know to close the bleed nipple after every pedal-press, before releasing pedal.
Yes.


Did you check to see if the Clutch master Piston was returning completely when let up on the pedal. Remember the pedal arm has its own return spring. If the piston isn't returning completely it could give you that No resistance feeling.
Yes the master cylinder's piston was moving 100% out, and the 50% play was with both the pedal and the master cylinder itself.


Now that you've Got 10% free play That's about right. I always use 1" or (25-30 MM) as a general rule for free play in clutch pedal.
Yes it does feel it has gone 100% back to normal now, on its own...!


It is possible to get a bubble of air "stuck" in the hose between the reservoir and the master cylinder. Especially if the hose is on the long side and makes a couple of bends. Tap and shake the hose to dislodge any air bubbles. If the hose looks like it is sweating it should be replaced. To bleed the system properly you need a flow to flush any air out, not just a trickle. If the fluid is not clear flush it good and then do the brakes.
It does have a bend in it, but also sweating. It was a new hose through DMCMW, I advised them of the relapse ofd sweating and they were escalating with DMCH - that was in October though I'll follow back up on that.

SS Spoiler
01-04-2014, 05:13 PM
Took note of Dave T. hint of air in a twisted clutch line. Went out and held line so air could bubble up to the cylinder, and heard/felt three bloops. I bet a lot of clutch cylinders have been unnecessarily replaced?



Paul Cerny #2691
Kalispell, MT

DMCMW Dave
01-04-2014, 06:59 PM
I bet a lot of clutch cylinders have been unnecessarily replaced?


They are usually replaced because they leak.

Delorean Industries
01-04-2014, 07:01 PM
Chris, are you still using an extended bleeder off the slave? I have seen a number of these not sealing at the threads into the slave causing issues.

Tillsy
01-04-2014, 07:13 PM
Chris, are you still using an extended bleeder off the slave? I have seen a number of these not sealing at the threads into the slave causing issues.

Negative, I removed it within an hour of installing - wasn't at all happy with it.

Someone (hint hint) should make a hardline version that brings it up to, and fixes it against, somewhere more accessible.

Delorean Industries
01-04-2014, 07:59 PM
Negative, I removed it within an hour of installing - wasn't at all happy with it.

Someone (hint hint) should make a hardline version that brings it up to, and fixes it against, somewhere more accessible.

I wanted to drop it down in a fixed hard line on the side of the transmission. The problem is in the bleeder fitting as it is an odd size. (7mm 1.0) with a high angle seat in the cylinder. It will be difficult to make something without modifying the slave itself or using a npt into the 7mm threads which is inadvisable.

Tillsy
01-05-2014, 05:15 AM
The clutch was still 100% back to normal this morning, so I did another test bleed - sure enough the pedal was back to 50% play after I did that. Waited 20 minutes and checked again - 100% back to normal.

Why is it doing that? It never did this during prior bleeds.

DMC5180
01-05-2014, 01:51 PM
Is it possible you have debris in the Reservoir or partially pinched/obstructed reservoir hose that is preventing the fluid from flowing into the cylinder during the bleed process? Your 20 minute rest period may be all that is needed for the Bubble to rise to the top of the res. or flow of fluid to enter the cylinder chamber.

DMC5180
01-05-2014, 02:08 PM
I wanted to drop it down in a fixed hard line on the side of the transmission. The problem is in the bleeder fitting as it is an odd size. (7mm 1.0) with a high angle seat in the cylinder. It will be difficult to make something without modifying the slave itself or using a npt into the 7mm threads which is inadvisable.

Interesting idea, theoretically you could gravity/syphon bleed the system that way as long as the bleeder is the lowest point.