PDA

View Full Version : Electrical Relocating The Ground For The Inertia Switch



kings1527
02-24-2013, 12:15 AM
I know some people have relocated the ground for the inertia switch but I'm having trouble locating exactly where the ground wire goes. I see all of the wiring go from the switch and then it all disappears into a bundle underneath the driver's side footwell. After it gets inside that bundle, I have no idea where it goes.

I have my interior completely gutted right now, so now's a better time than any to do this.

Can anyone point me in the right direction with a description and/or picture? Thanks!

Bitsyncmaster
02-24-2013, 05:51 AM
You don't need to trace the existing ground wire. Just cut it off near the switch leaving about 6 inches of wire. Then attach your new ground wire to that existing switch wire.

kings1527
02-24-2013, 12:14 PM
You don't need to trace the existing ground wire. Just cut it off near the switch leaving about 6 inches of wire. Then attach your new ground wire to that existing switch wire.

Of course! I was making that harder than it should be!

I'm not in front of my switch wiring. Can you tell me which pin is the ground? I'm guessing its black but I can't remember if there's only one black wire within the bundle or if there was multiple.

I saw your post on relocating it to the frame underneath the shift boot and that's where I'll go with it.

Again Dave, thanks for everything!

Bitsyncmaster
02-24-2013, 12:39 PM
Black wire is ground. Black/purple goes to the center (pump). Double brown/pink go to door lock and lock door light.

Chris 16409
02-24-2013, 01:07 PM
I just did this not too long ago. Just to note, when you get your wire, Dave told me the 10 gauge wire is overkill. I went with 12 gauge wire. I think he said AWG 14 would be fine too.

DMC5180
02-24-2013, 01:12 PM
ALL solid black wires are "grounds" or the "ground side" of any circuit in the DMC. It's a British Engineering Automotive wiring standard.

Bitsyncmaster
02-24-2013, 01:22 PM
I just did this not too long ago. Just to note, when you get your wire, Dave told me the 10 gauge wire is overkill. I went with 12 gauge wire. I think he said AWG 14 would be fine too.

Yes as small a14 AWG would be fine. I just used 10 AWG because I had a heavy duty terminal for that gauge. And I had some black wire about the right length.

kings1527
02-24-2013, 03:32 PM
Black wire is ground. Black/purple goes to the center (pump). Double brown/pink go to door lock and lock door light.

Perfect, thanks Dave!


ALL solid black wires are "grounds" or the "ground side" of any circuit in the DMC. It's a British Engineering Automotive wiring standard.

I had no idea about that. Thanks for the info.


Yes as small a14 AWG would be fine. I just used 10 AWG because I had a heavy duty terminal for that gauge. And I had some black wire about the right length.

Great, 14 gauge it will be. I remember seeing on other posts how a large gauge ground will create better accuracy in a variety of areas and reduce stress on the system.

Thanks again for all the help, guys, I appreciate it!

jawn101
02-24-2013, 07:25 PM
Perfect, thanks Dave!



I had no idea about that. Thanks for the info.



Great, 14 gauge it will be. I remember seeing on other posts how a large gauge ground will create better accuracy in a variety of areas and reduce stress on the system.

Thanks again for all the help, guys, I appreciate it!

Take lots of pics of the job, I'm curious how hard it really is on the swear-o-meter. The inertia switch ground is the only one I haven't made every reasonable effort to improve - mostly because I didn't know it existed when I did that project :)

Bitsyncmaster
02-24-2013, 08:03 PM
Take lots of pics of the job, I'm curious how hard it really is on the swear-o-meter. The inertia switch ground is the only one I haven't made every reasonable effort to improve - mostly because I didn't know it existed when I did that project :)

The reason to do this ground change is to get a better grounding of the instruments.

kings1527
02-24-2013, 08:34 PM
Take lots of pics of the job, I'm curious how hard it really is on the swear-o-meter. The inertia switch ground is the only one I haven't made every reasonable effort to improve - mostly because I didn't know it existed when I did that project :)

Will, do Jon! I'm in the middle of completely redoing my interior: I'm installing DPNW's Elite Wings-A-Loft system, a new sound system with the Infinity speakers/DMC CA sub enclosure from the other thread, and a DMCH reproduction carpet set, and converting everything to LEDs. I re-dyed all of the interior paneling the other day with SEM Acura Charcoal and it came out looking absolutely brand new. So as stripped down as I have the interior, the job to relocate the inertia switch ground can't get any easier! I think it'll take me about 5-7 minutes to take care of it. But I'll take a ton of pics and post them! On a side note, the Wings-A-Loft system is a pretty involved install.


The reason to do this ground change is to get a better grounding of the instruments.

That's what I was going after, particularly with the volt meter. I get a reading that's always below 13V and it'd be nice to get an accurate reading from it. I installed Hervey's main double ground wire but I've yet to run my car since I've installed it since I'm in the middle of other things. I also cleaned the contacts on the ground bundle located behind the bulkhead connectors (inside the car, above the relay compartment). I should also clean the connection it makes at the frame inside the engine compartment. I'm also going to make sure the ground bundle on the passenger side of the AC panel is in good shape and making good contact.

jawn101
02-24-2013, 09:42 PM
Will, do Jon! I'm in the middle of completely redoing my interior: I'm installing DPNW's Elite Wings-A-Loft system, a new sound system with the Infinity speakers/DMC CA sub enclosure from the other thread, and a DMCH reproduction carpet set, and converting everything to LEDs. I re-dyed all of the interior paneling the other day with SEM Acura Charcoal and it came out looking absolutely brand new. So as stripped down as I have the interior, the job to relocate the inertia switch ground can't get any easier! I think it'll take me about 5-7 minutes to take care of it. But I'll take a ton of pics and post them! On a side note, the Wings-A-Loft system is a pretty involved install.



That's what I was going after, particularly with the volt meter. I get a reading that's always below 13V and it'd be nice to get an accurate reading from it. I installed Hervey's main double ground wire but I've yet to run my car since I've installed it since I'm in the middle of other things. I also cleaned the contacts on the ground bundle located behind the bulkhead connectors (inside the car, above the relay compartment). I should also clean the connection it makes at the frame inside the engine compartment. I'm also going to make sure the ground bundle on the passenger side of the AC panel is in good shape and making good contact.

Don't forget the ground bundle behind the LFF/washer bottle and the one on the frame extension near the radiator fans.

kings1527
02-24-2013, 11:19 PM
I messed around with the radiator bundle back when I upgraded to DPNW's fans but I didn't clean the connection. I think I'll go back and do that just for good measure. And thanks for the heads-up on the washer bottle bundle. I didn't know about that one. I'll have to check that one out.

SS Spoiler
02-24-2013, 11:49 PM
On the ground in left front wheelwell I welded a bolt to the frame and haven't had any problems with corrosion. all the ground wires are easy to service.

kings1527
03-02-2013, 01:19 PM
So an interesting thing happened and I can't figure out why. I cut the black ground wire on the inertia switch and attached a 12ga wire to the "switch" side of the connection. Since I have all of my interior out of the car, I decided to ground it to a seat belt bolt on the driver's side, right behind the emergency brake. I thought that'd be a good ground since that bolt is going right to the frame.

But once I tried to start the car, no luck. I re-wired it back to the way it was and of course it fired right up.

I guess it wasn't a good ground location but I can't really figure out why?

jawn101
03-02-2013, 01:26 PM
If it was the lower anchor bolt on the left side, that's not anchored to the frame. It screws into a metal cup that's mounted in the fiberglass, not actually to anything metal. Best bet is one running along the center console side, those actually go into the frame.

kings1527
03-02-2013, 01:40 PM
If it was the lower anchor bolt on the left side, that's not anchored to the frame. It screws into a metal cup that's mounted in the fiberglass, not actually to anything metal. Best bet is one running along the center console side, those actually go into the frame.

Ah ha. That would explain it. I was thinking all of the seat belt anchor bolts would go directly to the frame. Thanks Jon!

kings1527
03-06-2013, 12:02 AM
I just posted this on another thread, but it definitely applies here too.

I re-grounded my inertia switch to a body bolt on the driver's side center console, anticipating a jump in the volt meter. Not so much. I'm about 13.5V right now, which is much better than my previous 12.6-12.8V or so. But I think my big improvement was due to Hervey's double ground wire. After installing that, my meter jumped to 13.5V or so. But after I re-grounded the inertia switch, I don't remember it changing again at all. And I know it's grounded well, otherwise my car wouldn't start (been there).

Not a big deal. I do like the fact that the inertia switch ground is playing on its own golf course now.

Chris 16409
03-06-2013, 12:43 AM
I grounded mine to one of the bolts that secures the manual sifter box. Those bolts go directly into the frame.

kings1527
03-06-2013, 01:15 AM
I grounded mine to one of the bolts that secures the manual sifter box. Those bolts go directly into the frame.

I was thinking about doing that but since I had such great access to one of the body bolts (interior is all out), I just grounded it there. And the body bolts go directly to the frame, as well. I don't see it being a difference if I went to the shifter area.

As far as difficulty, Jon, it's not really fair because I have everything out of my car. If that weren't the case, I'd say it'd be about a two or three. It's really easy to do but the center console might cause problems.

Chris 16409
03-06-2013, 01:47 AM
Hey Jon,

Just like Alex said, it's not that difficult. The hardest part is soldering the new wire to the ground wire coming out of the inertia switch. Since you have to do the soldering inside the car, you have to make due with the space available. My advice is to unwrap the the inertia switch wires as much as you can so you can cut the original ground wire further up the harness. This allows you to work closer to the floor when you do the soldering.

kings1527
03-06-2013, 03:31 AM
+1. In fact, I didn't even solder. I cut the black ground at the inertia switch itself and then connected another wire to it with a butt end connector, crimping the connection. Then I put an eyelet connector on the other net and pushed that through the body bolt. I'll post pics tomorrow and ill definitely chronicle it later in my blog. Way easy, particularly when you have the interior out, as that gives you several options. Even with the interior in, you have some easy routes you could take.

Ryan King
03-06-2013, 11:43 AM
+1. In fact, I didn't even solder. I cut the black ground at the inertia switch itself and then connected another wire to it with a butt end connector, crimping the connection. Then I put an eyelet connector on the other net and pushed that through the body bolt. I'll post pics tomorrow and ill definitely chronicle it later in my blog. Way easy, particularly when you have the interior out, as that gives you several options. Even with the interior in, you have some easy routes you could take.

Don't crimp anything on. This is an important ground wire that you don't want coming apart. I have sworn off those crappy crimp connectors. They don't do a good job of connecting anything and can come loose. Solder and shrink wrap everything. Ground the pump to the frame where the shifter is.

Don't cut corners. Take the time to do it right

Bitsyncmaster
03-06-2013, 12:35 PM
I don't trust the insulated butt terminals because you can't inspect the crimp and those just crush the barrel. I do trust the uninsulated type with the crimper that makes the one "indent" in the barrel. But even then if it's easy to access, I solder the crimped connector. Then I use one or two layers of heat shrink.

kings1527
03-06-2013, 01:50 PM
Don't crimp anything on. This is an important ground wire that you don't want coming apart. I have sworn off those crappy crimp connectors. They don't do a good job of connecting anything and can come loose. Solder and shrink wrap everything. Ground the pump to the frame where the shifter is.

Don't cut corners. Take the time to do it right


I don't trust the insulated butt terminals because you can't inspect the crimp and those just crush the barrel. I do trust the uninsulated type with the crimper that makes the one "indent" in the barrel. But even then if it's easy to access, I solder the crimped connector. Then I use one or two layers of heat shrink.

Excellent. Thanks guys.