PDA

View Full Version : Suspension Spindle nut.



steve6864
02-24-2013, 02:14 PM
I`ve got the 36mm size hub/spindle nut on my passenger side hub.I mangled it slightly while getting it off to install my new bearings.Is it common to another car?Meaning can I go to my nearest Napa/Carquest and get one?Thanks,6864.

DMC5180
02-24-2013, 02:24 PM
Post a photo of the mangled nut. As far as being common it probably is if you can match the thread pitch. According to the torque specs its a M22 x 32 nut. I think the 32 is ref. for the wrench size. The socket size is 32MM or 1-1/4 SAE. I'm surprised you were able to get a 36 mm socket to work.

Jonathan
02-24-2013, 03:05 PM
Post a photo of the mangled nut. As far as being common it probably is if you can match the thread pitch. According to the torque specs its a M22 x 32 nut. I think the 32 is ref. for the wrench size. The socket size is 32MM or 1-1/4 SAE. I'm surprised you were able to get a 36 mm socket to work.

Isn't this nut being 32 mm or 36 mm part of the evolution of the chronology? Another one of those variances? I know when helping other owners do angle drive work, you need to have both socket sizes depending on who has what on their car. Likely the same for the outside nut on the passenger side as well I would assume?

sdg3205
02-24-2013, 03:22 PM
Isn't this nut being 32 mm or 36 mm part of the evolution of the chronology? Another one of those variances? I know when helping other owners do angle drive work, you need to have both socket sizes depending on who has what on their car. Likely the same for the outside nut on the passenger side as well I would assume?

I've got 32 AND 36 on 2510. So far I've seen no rhythm to the nut shenanigans.

DMC5180
02-24-2013, 03:38 PM
I did a little digging on this. I was not aware of the dual nuts sizes. Mine are all 32MM

My printed copy of the Parts manual has P/N 108514 listed with a note that it is for the LH outer (only) spindle and both inner and outer on the RH spindle. there is no VIN effectivity listed.

In the DMCH online parts catalog they show 2 P/N's listed with photo's for Item 10

108514 with the note mentioned above in the description. $10.68 This one appears to be 32 MM

110911 No special note mentioned $10.68 This one appears to be a larger wrench size in the photo, so 36MM makes sense here.

The thread sizes are the same for both nuts though.

In either case no VIN effectiveness are given.

steve6864
02-24-2013, 05:57 PM
All that being said,I can re-use my original,but,what is the best solution for a replacement.A nut and bolt shop or is there a cross reference I can use at my local parts store? Thanks6864.

DMC5180
02-24-2013, 06:18 PM
All that being said,I can re-use my original,but,what is the best solution for a replacement.A nut and bolt shop or is there a cross reference I can use at my local parts store? Thanks6864.

Their is no specific cross reference that I'm aware of. It is rare to have too replace one and when it is replaced MOST folks go with NOS from a DMC vendor.

In a nutshell, your on your own if you choose to spend time looking for an alternative.

One thing to note: These nuts are technically a ONE TIME use item. Your supposed to use replace them once removed. That rarely happens, unless the the nut is supplied in a KIT, like when replacing modern drive axles. As long as their is reasonable locking feature resistance, most just reuse them.

LordFly
02-24-2013, 10:45 PM
I doubt this is a rare part. A quick Google search brought up THIS LINK (http://shop.advanceautoparts.com/buy/products/283342-castellated-nut-spindle-nut-m22-1-5-hex-32mm-by-dorman-autograde-part-615-105-spindle-lock-nuts.html). Lists a bunch of different cars it fits. I'm sure if you take it to NAPA they'll find you a match pretty quick, unless you're real picky about all parts being original.