Log in

View Full Version : Engine Quick Question about warmup regulator-Please help



DMC Fanatic
03-02-2013, 07:19 PM
Hi,

I recently replaced my warmup regulator with a rebuilt one from DMC Houston. Before I replaced it the car ran fine cold and warm, but had a fluctuating idle when cold like some DeLoreans do. After I replaced the WUR the car ran and drove fine, but I still had the fluctuating idle but it wasn't as bad as before. The next day I took it for a ride and I noticed that the engine is accelerating poorly and I can hear a slight "popping" noise. It seems almost like the car has a lot of hesitation while driving and when I step on the gas, the tachometer is very sloppy, like the needle creeps up slowly to get to speed. This has never happened before I replaced the WUR. However, the car idles fine. Can this be related to the new WUR I installed? I wasn't sure if the WUR has any kind of effect on a warm engine and would cause warm driveability issues? Any help would be appreciated.

Thanks,

Sean

sdg3205
03-02-2013, 07:30 PM
Hi,

I recently replaced my warmup regulator with a rebuilt one from DMC Houston. Before I replaced it the car ran fine cold and warm, but had a fluctuating idle when cold like some DeLoreans do. After I replaced the WUR the car ran and drove fine, but I still had the fluctuating idle but it wasn't as bad as before. The next day I took it for a ride and I noticed that the engine is accelerating poorly and I can hear a slight "popping" noise. It seems almost like the car has a lot of hesitation while driving and when I step on the gas, the tachometer is very sloppy, like the needle creeps up slowly to get to speed. This has never happened before I replaced the WUR. However, the car idles fine. Can this be related to the new WUR I installed? I wasn't sure if the WUR has any kind of effect on a warm engine and would cause warm driveability issues? Any help would be appreciated.

Thanks,

Sean

Sean - are you 100% sure you reattached the fuel lines correctly?

Bitsyncmaster
03-02-2013, 07:38 PM
You would need to adjust the mixture unless the old WUR happed to be set the same as the new one.

DMC Fanatic
03-02-2013, 08:09 PM
I made sure I hooked up the fuel lines in their correct ports on the WUR. I didnt know about adjusting the mixture after replacing it though. Does this have to do with how the new one has the port plugged up instead of using the screen like in the original one? Also, I noticed that the frequency valve is buzzing all the time now instead of cycling on and off like it did before.

Bitsyncmaster
03-02-2013, 08:20 PM
I made sure I hooked up the fuel lines in their correct ports on the WUR. I didnt know about adjusting the mixture after replacing it though. Does this have to do with how the new one has the port plugged up instead of using the screen like in the original one? Also, I noticed that the frequency valve is buzzing all the time now instead of cycling on and off like it did before.

If your FV has changed it buzzing then your mixture has changed. The FV should always buzz when the mixture is adjusted correctly. The new WUR use a brass filter which may look like a solid.

DMC Fanatic
03-02-2013, 08:37 PM
Do you suggest that I shouldn't adjust the mixture screw then? What can be causing my problem?

sdg3205
03-02-2013, 08:42 PM
Do you suggest that I shouldn't adjust the mixture screw then? What can be causing my problem?

Dave is probably right - you're running too rich or lean. The FV operates within a specific range to keep mixture on track and if the mixture is so far off that the FV can't compensate then I believe it just runs balls-out IIRC.

You need a dwell meter and an allan key. There are some good descriptions of how to adjust the mixture available by search.

DMC Fanatic
03-02-2013, 08:52 PM
Thank you for the suggestions. I think I'll try adjusting the mixture screw and go from there. It does seem like the engine could be to lean if its accelerating poorly. It also makes sense that changing the WUR can throw the mixture off.

DMC Fanatic
03-02-2013, 08:58 PM
One more question..I know that the mixture has to be set on a hot engine with the o2 sensor disconnected, but do you do this with the engine running or off?

sdg3205
03-02-2013, 09:05 PM
One more question..I know that the mixture has to be set on a hot engine with the o2 sensor disconnected, but do you do this with the engine running or off?

You set the base mixture with the engine off, RPM relay jumpered, engine cold and injectors out and in clear bottles - you adjust the mixture screw until the injectors just start to open up then you back it off so they stop.

You adjust the running mixture with the car warm, O2 sensor should be connected as normal. Depending on your dwell meter, you're looking for an average swing (analogue) or set duty cycle of 40 IIRC.... its been a while since I've done this. Martin G. wrote a good "How To" that I used.

EDIT - before you make any changes to your mixture ensure your vacuum lines are routed properly at the WUR or that they havent slipped off anywhere else.

jawn101
03-03-2013, 06:59 PM
You set the base mixture with the engine off, RPM relay jumpered, engine cold and injectors out and in clear bottles - you adjust the mixture screw until the injectors just start to open up then you back it off so they stop.

You adjust the running mixture with the car warm, O2 sensor should be connected as normal. Depending on your dwell meter, you're looking for an average swing (analogue) or set duty cycle of 40 IIRC.... its been a while since I've done this. Martin G. wrote a good "How To" that I used.

EDIT - before you make any changes to your mixture ensure your vacuum lines are routed properly at the WUR or that they havent slipped off anywhere else.

What he said: the poor acceleration could easily just be a loose or torn vacuum line at the WUR. Had the exact same thing happen to me last year.

DMC Fanatic
03-03-2013, 09:25 PM
Unfortunately it's not a loose or torn vacuum line since I double checked those; I wish it was though..lol. Still looking to adjust the mixture but haven't gotten around to doing it yet since I have to go buy a long 3mm allen key first. I'm still convinced that the car is running to lean.

David T
03-03-2013, 09:50 PM
Recheck the routing of the vacuum hoses to the control pressure regulator. Verify the check valve is installed in the correct direction. Before disturbing the mixture screw I would check the control pressure as the motor warms up.If it is running lean you may just have a vacuum leak. Screwing the mixture screw to to try to richen the mixture is not going to fix a vacuum leak. You do have a plug in the housing over the mixture screw, right! If not that may be the reason it is running lean. Do not attempt to turn that screw without some kind of instrumentation to see what you are doing. That adjustment is VERY sensitive and if it hasn't been disturbed, chances are it is right where it is supposed to be. I have yet to see anyone "fix" a Delorean by just turning that screw. That is unless the mixture unit was serviced or changed. If it was, then it may require an adjustment.
David Teitelbaum

DMC Fanatic
03-03-2013, 10:00 PM
Looks like the check valve is installed in the correct direction and I do have a plug over the mixture screw. The funny thing is that I've never had these driveability issues until after I replaced the WUR with the new one. Shouldn't the one require an adjustment or is it supposed to be a plug and play type part?

DMCMW Dave
03-03-2013, 10:15 PM
Looks like the check valve is installed in the correct direction and I do have a plug over the mixture screw. The funny thing is that I've never had these driveability issues until after I replaced the WUR with the new one. Shouldn't the one require an adjustment or is it supposed to be a plug and play type part?

If the CO was adjusted to be more correct with a bad one, installing a good one will upset the adjustment. Why did you replace it? How did you know it was bad?

DMC Fanatic
03-05-2013, 09:29 AM
Going to be doing the mixture adjustment today. I bought a dwell meter from sears, but i"m not 100% sure on how to hook it up. After looking through the old archives on how to hook it up, someone said theres a orange wire around the firewall that the dwell meter plugs into, but I don't see that wire. I have the little black diagnostic box that supposedly the orange wire goes too, so can I hook it up to there? What pin would I use in that box? Cause it looks like the diagnostic box is in pretty good shape. I also wasn't sure if the wire from the dwell meter would fit into one of those tiny pins?

Jack
03-05-2013, 11:03 AM
Going to be doing the mixture adjustment today. I bought a dwell meter from sears, but i"m not 100% sure on how to hook it up. After looking through the old archives on how to hook it up, someone said theres a orange wire around the firewall that the dwell meter plugs into, but I don't see that wire. I have the little black diagnostic box that supposedly the orange wire goes too, so can I hook it up to there? What pin would I use in that box? Cause it looks like the diagnostic box is in pretty good shape. I also wasn't sure if the wire from the dwell meter would fit into one of those tiny pins?

Just unplug the wire from the bottom of the box.

David T
03-05-2013, 11:41 AM
Refer to Workshop Manual M:03:01. You want the ground, #2, yellow, and Lambda #3 orange.
David Teitelbaum

Bitsyncmaster
03-05-2013, 09:03 PM
The two pin black connector near the firewall center has an orange wire and a purple wire. You connect the orange wire to the + side of the dwell and the engine block to the - side of the dwell.

DMC Fanatic
03-06-2013, 10:59 PM
Just a quick update: I set my mixture tonight by using the dwell meter and it's fluctuating between 30 and 40 on a warm engine which is suppose to be normal. I'm still having the same symptoms though :cry: Does anyone else have any other things that I can try? At this point I'm thinking of just having it towed to PJ Grady. Thank you all for your suggestions so far:smile:

David T
03-06-2013, 11:53 PM
Poor acceleration can be caused by any number of things including:
bad ignition wires
bad ignition coil
plugged cat
dirty air filter
bad pick-up hose
timing off or vac or mech advance not working
Bad CPR

You have to try to eliminate these one-by-one till you stumble on the cause. At least you can figure you don't have any bad vacuum leaks and your Lambda system is functioning. I would do a timing check and then get a pressure gauge on the fuel system. Another "trick" is to run the motor in the dark and look at the ignition wires, if you see sparking or a blue haze near them they are bad. This is not a perfect test however, they can still be bad where they go into the wells for the plugs. That brings up another idea, is there any water in the spark plug wells? That could cause this symptom. To test for a bad cat you put a vacuum gauge on the intake and if as you rev the motor up the vacuum goes down, the car is plugged up.
David Teitelbaum

pezzonovante88
03-06-2013, 11:58 PM
This is not a perfect test however, they can still be bad where they go into the wells for the plugs. That brings up another idea, is there any water in the spark plug wells? That could cause this symptom.
David Teitelbaum

Poor engine performance due to water in the plug wells would only be short-term, correct? Would the water not burn-off or evaporate?

jawn101
03-07-2013, 02:00 AM
Poor engine performance due to water in the plug wells would only be short-term, correct? Would the water not burn-off or evaporate?

It would take a pretty long time for that to happen. The wells are deep and if the wet plug's cylinder isn't firing, it would be cooler there.

DeLorean03
03-08-2013, 03:36 AM
It would take a pretty long time for that to happen. The wells are deep and if the wet plug's cylinder isn't firing, it would be cooler there.

I will DEFINITELY vouch for that.

If you get water in there, get a shop vac or some paper towels. It can take a WHILE - sure took longer than my patience could handle.

DMC Fanatic
03-08-2013, 05:34 PM
Well I decided to go ahead and change the spark plugs and wires first to see if that's the problem. My wires look pretty bad anyway. This is probably a stupid question, but I ended up buying Autolite platinum spark plugs, so are these any good? I unfortunately already installed them before reading that platinum plugs are no good for the DeLorean :banghead: Is it worth throwing them away and buying basic copper or silver plugs? There not double platinum or anything so hopefully they'll be ok. I really wish I researched this first!

Thanks,

Sean

Bitsyncmaster
03-08-2013, 06:23 PM
I ran the platinum plugs for 5 years with no problems. I just changed them because of all the warnings posted here about them.

DMC Fanatic
03-08-2013, 09:04 PM
ok cool :smile: Yeah I figured I mine as well try them before I go waste money on another set of plugs :p Hopefully they'll be good with no issues. Thanks!